812264
64
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
Installation instructions
for the specialist company
LEVANA 2.0 6 kW
LEVANA 2.0 8 kW
LEVANA AQUA 2.0
ARINA 2.0
INARA 2.0
EN
Installation of a combustion air damper for automatic opening
and closing of the combustion air line (optional)
A closed combustion air line prevents warm air from escaping from
the installation room unnecessarily with the stove turned o.
Note! The combustion air damper is closed in the “O operat-
ing state. It is open in all other operating states (“Ready”, “Ignition,
“Start, etc.).
The actuator takes approx. 2 minutes to reach the closed” posi-
tion, i.e. the pellet replace may be switched o at the master
switch 2 minutes after “O appears on the display at the earliest.
The user of the pellet replace should also be informed of this
.
1
2
6
7
5 4 3 2
Fig. 2.20 Connection of a motor-driven combustion air damper
1Motor slewing ring
2Stops for the combustion air damper (open/closed)
3“S19” connector
4“L continuous” connector (must be connected to the
“L continuous” mating connector in the wiring harness)
5“S5” connector
6Combustion air damper screwed onto the rear
7Combustion air damper screwed onto the bottom
If other accessories are installed in addition to the automatic, mo-
tor-driven combustion air damper, take care to ensure, for reasons
of accessibility, that the combustion air damper is installed rst.
For the same reason, the side walls should also be installed rst
after installing the combustion air damper!
Connect the combustion air damper connector into the wiring
harness and to the main circuit board of the pellet replace as fol-
lows before installing the combustion air damper:
a) Plug the “19” connector into position “S19” on the main circuit
board (see connection diagram!)
b) Plug the “S5” connector into position “S5” on the main circuit
board.
c) Plug the “L continuous” connector into the “L continuous” con-
nector in the pellet replace wiring harness!
Follow a similar procedure to that which is set out in the “Conversion
of combustion air nozzles for connection from the bottom chapter:
Remove the lower back wall and panel!
Release the hose clamp on the combustion air line!
Remove the combustion air nozzles!
Plug the connecting piece for the combustion air damper into the
combustion air line and tighten the hose clamp again!
Screw the combustion air damper onto the rear or bottom of the
pellet replace!
311x
Fig. 2.21 Remove the lower back wall and panel
64
We reserve the right to make technical changes
78-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 6478-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 64 11.04.2023 14:41:4711.04.2023 14:41:47
64

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Olsberg ARINA 2.0 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Olsberg ARINA 2.0 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 34.97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info