423827

Oki of 5400 Handleiding

25
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
OKIFAX
5400
User’s Guide
Preface i
Every effort has been made to ensure that the information in this document
is complete, accurate, and up-to-date. The manufacturer of this equipment
assumes no responsibility for the results of errors beyond its control. The
manufacturer of this equipment also cannot guarantee that changes in
software and equipment made by other manufacturers and referred to in
this guide will not affect the applicability of the information in it.
Mention of software products manufactured by other companies does not
necessarily constitute endorsement by the manufacturer of this equipment.
This user’s guide is subject to change without notification.
This product complies with the requirements of the Council Directives 89/
336/EEC and 73/23/EEC on the approximation of the laws of the member
states relating to electromagnetic compatibility and low voltage.
Copyright 1999 by Oki. All rights reserved.
Written and produced by Oki Europe Ltd.
OKI and OKIFAX are registered trademarks of Oki Electric Industry
Company, Ltd.
Energy Star is a trademark of the United States Environmental Protection
Agency.
ii User’s Guide
ENERGY STAR
As an Energy Star Partner, Oki has
determined that this product meets the
Energy Star guidelines for energy efficiency.
Preface iii
Table of Contents
Safety
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installation hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Operation & maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Toner cartridge & image drum handling . . . . . . . . . . . . . . . . . . . . . . . 3
Emergency first aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Introduction
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Product options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Second paper cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PC interface board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Component Identification
What you should receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Control panel keys & indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
One touch keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using one touch keys for dialling . . . . . . . . . . . . . . . . . . . . . . . 16
Using one touch keys for selecting functions & programming . 17
Signal tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installation
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Where to install your fax machine . . . . . . . . . . . . . . . . . . . . . . . . . 19
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installing document stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installing toner cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting telephone line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing external handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting external telephone or answering machine . . . . . . . . . 24
Connecting power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Loading paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Setting time & date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
iv User’s Guide
Setting answering mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Answering mode options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Changing answering mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Fax machine identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Setting fax machine identification . . . . . . . . . . . . . . . . . . . . . . . . . .31
Setting forwarding number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Setting language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Connecting to a PBX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Dial Directories
One touch keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
One touch parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Chain dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Auto dial numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Basic Operations
Preparing documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Document size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Multiple page documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Loading documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Sending faxes to single location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Search key dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Real-time dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Redialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Confirming results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Stopping transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Receiving faxes manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Receiving faxes into memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Memory reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
No paper reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
No toner reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Cancelling messages stored in memory . . . . . . . . . . . . . . . . . . . . .47
Rejecting unsolicited fax messages . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Power failures & memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Making copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Making copies using manual paper feeder . . . . . . . . . . . . . . . . . . .49
Using voice request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Initiating voice request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Preface v
Answering voice request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Advanced Operations
Sending faxes to multiple locations . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Delayed sending of faxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Sending delayed fax from document feeder . . . . . . . . . . . . . . . . . 54
Sending delayed fax from memory . . . . . . . . . . . . . . . . . . . . . . . . 55
Cancelling delayed transmissions . . . . . . . . . . . . . . . . . . . . . . . . . 56
Confidential faxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Sending confidential faxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Receiving confidential faxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Creating confidential mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Changing password or closing mailbox . . . . . . . . . . . . . . . . . . . . . 59
Printing confidential faxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Relay broadcasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Relay initiating station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Relay key station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Relay broadcast report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Initiating relay broadcasts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Polling transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Polling reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Dual access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
While sending faxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
While receiving faxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
While making copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
While printing reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Programming
Customising features & operations . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Viewing your current settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
User function settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
User function settings list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Changing user function settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Dial parameter settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Dial parameter settings list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Changing dial parameter settings . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Service function settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Service function settings list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
vi User’s Guide
Reports
Uunderstanding reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Activity report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Broadcast confirmation report . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Telephone directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Configuration report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Message confirmation report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Confidential reception report . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Broadcast entry report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Power outage report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Printing reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Printing message confirmation report . . . . . . . . . . . . . . . . . . . . . . .78
Printing other reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Codes used in reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Result codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Communication codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Problem Solving
Clearing document jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Clearing printer paper jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Replacing toner cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Replacing image drum unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Reading print counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Problem checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Specifications
Safety 1
English
Safety
Your fax machine has been carefully designed to give you years of safe,
reliable performance. As with all electrical equipment, however, there are
a few basic precautions you should take to avoid hurting yourself or
damaging the fax machine.
General
• Read this user's guide carefully and keep it in a safe but accessible
place so that you can use it for future reference.
• Read and follow all warning and instruction labels on the fax
machine itself.
• Disconnect the fax machine before you clean it. DO NOT use liquid
or aerosol cleaners to clean the fax machine.
• Place your fax machine on a firm, solid surface. If you place the fax
machine on something unsteady, it may fall and become damaged
or injure someone. If you place the fax machine on a soft surface,
such as a rug, sofa, or bed, the vents may become blocked causing
the fax machine to overheat.
• Do not use your fax machine near water, or spill liquid of any kind
into it.
Installation hints
• Install your fax machine in a dust-free location away from direct
sunlight.
• Do not connect your fax machine to a power source that is used by
other equipment producing electrical noise (i.e., air conditioners,
etc.).
• Leave electronic adjustments to authorized service personnel.
• The LINE terminal connects your fax machine to a standard
telephone line. To avoid damage to your telephone system or to the
2 User’s Guide
fax machine, do not connect your fax machine into anything other
than a standard telephone socket.
• Your fax machine has an earthed, 3-pin plug as a safety feature and
it will only connect to an earthed outlet. If you cannot connect this
plug to your power outlet, then it is possible that you have an older,
non-earthed outlet. Contact an electrician to have your power outlet
replaced. Do not use an adapter to defeat the earthing.
• The electrical power outlet should be located near the fax machine
and should be easily accessible.
• The TEL ports on the back of the fax machine are only suitable for
2 wire devices. Not all standard telephones will respond to
incoming ringing when connected to an extension socket.
• This fax machine may not necessarily provide an effective hand-
over of a call from a telephone connected to the same line.
• The operation of this fax machine on the same line as a telephone or
other equipment with audible warning devices or automatic ring
detectors will rise to bell tinkle or noise and may cause false
tripping of the ring detector. Should such problems occur, the user
is not to contact the telephone company.
Operation & maintenance
• Use a dry cloth to clean the control panel and the main body of the
unit.
• Aside from the instructions specifically mentioned in this user’s
guide, your fax machine is not user serviceable. DO NOT attempt to
service the machine or lubricate moving parts by yourself.
• Disconnect the power cable before trying to remove any objects that
may have fallen into the machine.
• Immediately disconnect the fax machine if it becomes physically
damaged and arrange for its repair or disposal.
• When relocating your fax machine, always disconnect the
telephone line before disconnecting the power cable. When
reconnecting your fax machine, connect the power cable first, then
the telephone line.
• This fax machine is not intended to be used in parallel with any
other telephone devices.
Safety 3
English
Toner cartridge & image drum handling
• Leave unused toner cartridges and image drum units in their
packages until needed. When replacing a toner cartridge or image
unit, reuse the packaging to dispose of the old toner cartridge or
image drum unit.
• Do not expose the toner cartridges and image drum units to light for
more than five minutes. Never expose the green drum (inside the
image drum unit) to direct sunlight.
• Always hold the image drum unit by the ends - never by the middle.
Never touch the green drum inside the image drum unit.
• To avoid damage to the image drum unit, always use original Oki
toner cartridges.
• Exercise care when removing the toner cartridge. Do not let it touch
your clothing or porous materials. The toner powder causes
permanent stains.
• Small amounts of toner spilled on skin or clothing can be readily
removed with soap and cold water. Using heated water will make
removing the stain much more difficult.
Emergency first aid
•
IF TONER IS SWALLOWED:
Induce vomiting and seek medical
attention. Never attempt to induce vomiting or give anything by
mouth to a person who is unconscious.
•
IF TONER IS INHALED:
Take the person to an open area for
fresh air. Seek medical attention.
•
IF TONER GETS IN THE EYES:
Flush eyes with large
quantities of cool, NOT cold, water for a minimum of 15 minutes
keeping eyelids open with fingers. Seek medical attention.
4 User’s Guide
Inroduction 5
English
Introduction
Thank you for purchasing this OKIFAX fax machine. This fax machine
uses advanced Light Emitting Diode technology to transfer received and
copied images to plain paper. It has been designed to make sending and
receiving faxes a fast and trouble-free process.
Features
The OKIFAX 5400 includes all the following features:
• 30 One Touch keys for automatic, single-key dialling of
pre-programmed telephone numbers.
• 99 Auto Dial numbers for automatic dialling of additional
pre-programmed telephone numbers.
• Group programming (20 groups) allowing transmission of a
document to multiple locations with a single selection.
• A search feature allowing you to look for pre-programmed
telephone numbers by name.
• Halftone transmission in up to 64 shades of gray.
• High-speed fax transmission and reception at up to 28,800 bits per
second.
• 16 mail boxes for confidential transmission and reception.
• Automatic redial and page re-transmission when a telephone
number is busy or when problems occur in communication.
• Advanced transmission and reception features, including delayed
transmission, transmission to multiple locations, confidential
transmission and reception, relay broadcast initiate and polling.
• Advanced memory transmission and reception features, including
automatic reception into memory with or without password
printing.
• Reports to help you keep track of your fax machine’s operations
and settings.
6 User’s Guide
• Automatic power save mode.
• Answering modes for manual and automatic fax reception,
automatic switching between incoming voice and fax messages.
Also allows an answering machine to be connected in series to the
telephone line after the fax machine.
• A closed network feature to allow you to limit who can send faxes
to your fax machine, or to limit both where faxes can be sent to and
received from.
• Your fax machine can also make up to 99 sorted copies of an
original document using standard weight (80 g/m
2
) paper.
• 2.5 Mb of built-in memory.
• An advanced dual access feature which allows you to load and
prepare multiple documents for transmission while your fax
machine is sending or receiving another message.
• High-speed scanning of original documents.
• A manual paper tray to allow you to load a different type of paper
while making copies. Paper size is dependent on 1st paper size
setting.
• A fax forwarding feature to allow your fax machine to receive
messages into memory and automatically forward the messages to
another remote fax machine.
Product options
A number of options are available to increase the usefulness and
convenience of your fax machine.
Memory expansion
Installing additional memory allows the fax machine store to more pages
of information in memory. If you are constantly seeing a MEMORY
OVERFLOW message on your fax machine, you should consider
purchasing additional memory. An optional 4 Mb memory expansion
board is available.
The memory expansion board option includes a built-in backup battery.
This feature protects memory operations and other communication
settings for up to one hour in the event of a power failure.
Inroduction 7
English
Second paper cassette
The second paper cassette option adds an additional 500 pages of paper
capacity to your fax machine. When the main paper cassette runs out of
paper, your fax machine automatically switches to the second paper
cassette to continue printing received faxes or copies.
PC interface board
This allows your fax machine to communicate with a personal computer.
Once the option is installed, you can:
• Use your fax machine as a local printer.
• Send fax messages directly from your computer.
• Receive and store fax messages on your computer.
• Scan pages from your fax machine into your computer.
• Program One Touch Keys, Auto Dial Numbers and groups into your
fax machine from a personal computer.
8 User’s Guide
Component Identification 9
English
Component Identification
What you should receive
Fax Machine
Document Stacker
Power Cable
Telephone Cable
Image Drum Unit
(inside fax machine)
Toner Cartridge
Optional External
Handset
10 User’s Guide
Components
1 One Touch Keypad
2 Document Table:
Covers the copy stacker and hols original
documents that are to be faxed or copied.
3 Document Table Extension:
Flips out to support longer documents
that are to be faxed or copied.
4 Copy Stacker:
Holds copies or received faxes.
5 Front Panel:
The panel on the front of the fax machine gives you
access to the manual paper feeder. This allows you to bypass the paper
cassette and feed paper directly into the machine. Use this feature when
you want to use a different type of paper.
6 Copy Stacker Extension:
Slide this tray out to help support copies
or received faxes.
7 Paper Cassette:
Holds up to 250 sheets of paper.
8 Paper Indicator:
Shows how much paper remains in the paper
cassette.
Component Identification 11
English
9 Power Switch:
Press the I to turn the fax machine ON and the O to
turn the fax machine OFF.
10 Document Guides:
Adjust these guides to the page width of teh
documents that are to be faxed or copied.
11 Control Panel
12 Document Stacker:
Holds your original documents after they have
been faxed or copied.
13 Paper Path Icon:
Load documents face down here.
14 AC Power Socket:
Connect the power cable supplied with your fax
machine into this socket.
15 Cable Run:
When installing the optional external handset, feed the
telephone cable through this cable run to TEL1 or TEL2 terminals.
16 TEL1/TEL2 Terminals:
Terminals for connecting the fax machine
to the optional external handset or an external telephone.
17 LINE Terminal:
Terminal for connecting the fax machine to a
telephone line.
18 Expansion Slot Cover:
Open this cover for access to expansion
slots for the optional PC interface board and memory expansion boards.
19 Image Drum Unit:
The image drum unit contains the
photosensitive drum which receives images from the LED print head and
transfers these images to the printing paper. You will need to change this
image drum unit about every 11 000 pages, depending on usage.
20 Toner Cartridge:
This black cylinder, installed inside the image
drum unit, contains black powder which acts as the ink for your fax
machine.
12 User’s Guide
21 LED Print Head:
This black bar is the part of your fax machine
which transfers received or copied images onto the image drum unit. Clean
this bar each time you change a toner cartridge.
Control panel keys & indicators
1 LCD Panel:
Refer to this liquid crystal display (LCD) panel for
instructions and information while your fax machine is operating or while
you are programming your fax machine.
2 Copy Key:
After loading a document, press this key to make a copy.
When no documents are loaded, press this key to obtain a Message
Confirmation Report about your last transmission.
3 Hyphen Key:
When programming One Touch keys and Auto Dial
telephone numbers, use this key to tell your fax machine to wait for the
outside or international line to become available before it proceeds with
dialling the rest of the telephone number. When programming the TSI/CSI
or call back numbers into your fax machine, use this key to enter a “+”
symbol.
4 Search Key:
One Touch keys and Auto Dial numbers can be
programmed to have a name or location ID associated with their telephone
numbers. Using this key by itself or in combination with the numeric
keypad, you can search for these numbers alphabetically.
Component Identification 13
English
14 User’s Guide
5 Auto Rec Key:
This key sets the answering mode of your fax
machine. The answering mode controls how your fax machine answers
incoming calls and receives faxes. The display of your fax machine will
always indicate your current selection. See Setting Answering Mode in
Installation for more information about the answering modes available in
your fax machine.
6 Select Function Key:
Using this key activates the advanced
transmission and reception functions, to obtains report and for
programming. To select a function, press the Select Function key, then
press the One Touch key labelled with the function you want to use. While
programming or selecting other functions, pressing the Select Function
key a second time takes you directly back to the stand-by mode of your fax
machine.
7 Auto Dial Key:
Auto Dial numbers are abbreviated numbers for
rapid dialling. Rather than dialling the entire telephone number, you can
enter a 2-digit code number to Auto Dial number instead. You can also use
the Location IDs (names) associated with Auto Dial numbers to search for
these locations by name using the Search key.
8 Redial Key:
Pressing this key manually redials the last number
dialled on your fax machine.
9 Hook/V. Request Key:
Press the Hook/Voice Request key to open
a telephone line for manual dialling. You will be able to hear the dialling
through the speaker of your fax machine.
If you have an optional telephone handset or external telephone connected
to your fax machine, you can also use this key to initiate or answer a
request for voice communication. During a fax communication, press the
Hook/Voice Request key to tell the operator at the other fax machine that
you want to talk at the end of your transmission or after reception of any
page has been completed. To answer a voice request, press the Hook/
Voice Request key after lifting your telephone handset.
10 One Touch Keypad:
For a description of all the functions of the
One Touch keypad, see “One touch keypad” on page 16.
11 One Touch Labels:
After programming a location into a One Touch
key, write the name of the location on the One Touch label. Lift off the
plastic cover and use a pencil to write in the name, then replace the cover.
12 Numeric Keypad:
When dialling, these twelve keys work like the
keypad on a telephone. You will also use the keypad to enter numbers,
letters and other characters while programming.
13 */Tone Key:
If your fax machine is set to pulse dialling, this key
allows you to switch the dialling operation of your fax machine from pulse
Component Identification 15
English
to tone dialling during your current call. You can also use this key while
programming to create numbers with mixed pulse-then-tone operation.
14 0/Unique Key:
When dialling, use this key to enter a “0”. When
programming your Sender ID or a Location ID, you can use this key to
enter a variety of unique characters, e.g. ! # & ‘ ( ) * + , – . / : ; = ? _ ä ß ñ
ö ü Æ Å Ø æ å ø.
15 Transmit Resolution/YES key:
This key changes the resolution
used for transmitting documents. Use STD for standard originals, FINE
and EX.FINE for detailed or small print originals, and PHOTO for
originals that include colours or many shades of gray.
You will also use the YES key when making selections or to move your
cursor while programming.
16 Type of Original/NO key:
This key selects the document contrast
after loading a document for transmission. Use LIGHT for originals that
are too light, NORMAL for documents with good contrast, and DARK for
originals that are too dark.
You will also use the NO key when making selections or to move your
cursor while programming.
17 Alarm Indicator:
This indicator glows red and an alarm sounds to
notify you of any problem that occurs. To turn the alarm indicator off,
press the Stop key and correct the problem.
18 Stop Key:
This key cancels any operation currently in progress and
turns off the Alarm Indicator. During programming, pressing the Stop key
takes you back step-by-step through the programming functions you have
already selected.
19 Start Key:
Pressing the Start key initiates the operation indicated on
the display or confirms information you have entered into the display.
20 Plus (+) Key (One Touch Key 13 and 28):
Each fax number you
enter or program into your fax machine can be up to 32 digits long. When
a number is longer than 32 digits, it is possible to dial this number using
combination of One Touch keys, Auto Dial numbers or the numeric
keypad. When programming a chain dial number into a One Touch key or
Auto Dial number, press the Plus key at the end of the first part of the
number to indicate to the fax machine that this is a chain dial number.
21 Space Key (One Touch Key 14 and 29):
Use this key on the One
Touch Keypad to enter spaces while programming or to erase previously
programmed information. Unlike the Pause key, spaces are used for easier
reading only and have no effect on dialling.
16 User’s Guide
22 Pause Key (One Touch Key 15 and 30):
Use this key on the One
Touch keypad to enter automatic 3-second pauses in dialling when
programming telephone numbers. For example, you may want to use this
key to tell your machine to wait for an outside or international line to open.
Pauses in telephone numbers are marked by a “P” symbol.
One touch keypad
The One Touch keys are an important tool on your fax machine. You will
use them for quick, one-touch dialling, and to access the functions and
programming options of your fax machine.
Using one touch keys for dialling
To use a One Touch key for dialling, just press the appropriate One Touch
key. For each key, you may program up to two telephone numbers: a
primary number, which will always be dialled first, and an alternate
number which will be automatically dialled if the first number is busy or
if there is no answer.
You can also use the Location IDs (names) associated with One Touch
keys to search for these locations by name using the Search key.
There are 30 One Touch Keys available for programming. To access One
Touch keys 16–30, grasp the One Touch keypad latch and swing the main
One Touch panel up and out of the way. When you are finished, close the
One Touch keypad to continue with other options and programming.
Component Identification 17
English
Using one touch keys for selecting functions & programming
You will also use One Touch keys 1 to 10 for selecting special
transmission and reception functions, obtaining reports and programming.
To select a function from the One Touch keypad, press the Select Function
key, then press the corresponding One Touch key.
1 Delayed TX Key:
Use this key to send a fax at a later time and date
which you can specify for up to three days later.
2 Broadcast Feeder TX Key:
Use this key to send a fax to multiple
locations.
3Confidential TX Key:
Using this key sends a confidential
document to a personal mail box (a memory storage area) in the receiving
fax machine.
4 Relay Initiate TX Key:
Using this key sets up a relayed fax
transmission. During a relayed fax transmission, your fax machine
initiates the transmission by sending a document to a second fax machine,
which then broadcasts the message to a number of other fax machines.
5 Polling Key:
When a document is loaded on the document table, use
this key to set your fax machine to wait for another fax machine to call and
request the document to be sent (polling transmission). When no document
is loaded on the document table, using this key calls another fax machine
and requests it to send the documents it has loaded into memory (polling
reception).
6 Report Print Key:
Using this key manually prints reports from your
fax machine.
7 Counter Display Key:
Your fax machine keeps track of the number
of pages it has printed and scanned. Using this key checks the print
counters of your fax machine and resets the drum counter of your fax
machine after replacing the image drum unit.
8 Location Program Key:
Using this key programs One Touch keys,
Auto Dial numbers and groups into your fax machine.
9 User Program Key:
Using this key allows you to program
identification informationof your fax machine, set the clock of your fax
machine and to change the function settings of your fax machine.
10 Message Print From Memory Key:
Your fax machine can be set
to receive messages into memory and not print them when it runs low on
toner. Using this key you can also force messages to print when toner is
low, but print quality may be poor.
18 User’s Guide
Using this key prints out confidential fax messages received into mail
boxes in the memory of your fax machine after entering the correct
password.
When no messages are in memory, using this key prints a cleaning page to
clear accumulated toner from your fax machines image drum.
Signal tones
Your fax machine emits a number of sounds to inform you of specific
conditions.
Key Select Tone:
This is a short beep that occurs each time you press a
key.
Error Tones:
If you press a wrong or inappropriate key, your fax machine
will emit three short beeps. If your fax machine experiences a problem
during communications, it will emit three long beeps. Press the Stop key
to turn the error tone off, then print a Message Confirmation Report to
check the source of the problem by pressing the Copy key twice with no
documents loaded.
Voice Request Tone:
During a fax session, either you or the person at the
remote fax machine may initiate a voice request. When the person at the
remote fax machine either initiates or answers your voice request, your fax
machine emits a repetitive warbling sound.
End of Session Tone:
At the end of every successful fax session, your fax
machine emits a short beep to inform you that there were no errors or
problems in the communication.
Off-Hook Alarm Tone:
If your fax machine is equipped with a handset,
and if the handset is left off the hook, your fax machine will emit an
intermittent warbling sound. To turn off the sound, hang up the handset or
press the Stop key.
Installation 19
English
Installation
Getting started
To install your new fax machine, follow the instructions from Unpacking
to Setting the Fax Identification. You must complete these steps for your
fax machine to operate properly.
If you have purchased an option package for your fax machine, refer to the
documentation you received with that option.
Where to install your fax machine
• Install your fax machine in a dust-free location away from direct
sunlight.
• Allow several centimetres on each side of the fax machine to ensure
adequate ventilation.
• Make sure that both power and telephone outlets are available
nearby.
• Choose a location where the relative humidity is between 20% and
80%, and where the temperature is between 10°C/50°F and 32°C/
92°F.
Unpacking
Before you begin, be sure that all the items listed below are included in
your package. Refer to the illustrations in Component Identification to
identify the items. After removing the items from the carton, place them
on a sturdy surface.
• Fax machine unit
• Toner cartridge
• Image drum unit (inside facsimile unit)
• Power cable
• Telephone line cable
20 User’s Guide
• Paper tray/Copy stacker
• This user’s guide
Note:
A telephone handset, handset cradle and handset
cable may also be included. If any items are missing,
notify your dealer immediately for a replacement.
Keep your packing materials and carton in case you
ever need to ship or transport the machine.
Setting up
Installing document stacker
Slip the document stacker indents over the tabs on the rear of the unit. You
will feel them lock into place.
Installing toner cartridge
1. Lift the document table into an upright position.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
Installation 21
English
2. Push in the cover release buttons on the side of the copy stacker
until you hear a click. Lift the copy stacker.
3. Remove the protective foam cylinder from the toner well in the
image drum unit.
WARNING
Be careful when handling the toner cartridge. Do not let toner spill onto
your clothing or other porous materials. If you experience any problems
with toner, refer to the safety instructions at the beginning of this user’s
guide.
4. Remove the toner cartridge from its package and gently shake it
from side to side to distribute the toner. Then carefully peel the
white plastic tape from the bottom of the toner cartridge.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
ART
22 User’s Guide
5. With the ridged side facing up and the coloured lever on your right,
insert the toner cartridge into the image drum unit. Slide the left end
of the cartridge in first, then lower the right end into place.
6. Once the toner cartridge is in place, push the coloured lever all the
way forward to secure it and release the toner.
7. Close the copy stacker and push down until you hear the copy
stacker click into place. Be sure that the cover is latched on both
sides.
8. Close the document table.
Connecting telephone line
1. Insert one end of the telephone cable into the LINE terminal at the
back of the machine.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
STAR
T
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
START
Installation 23
English
2. Insert the other end of the telephone cable into your wall telephone
socket.
Note:
Now, you can connect either an external telephone or
the external handset option for your fax machine. See
the instructions below.
Installing external handset
If you purchased an external handset option with your fax machine, follow
these instructions to install it.
1. Using the supplied screw, connect the handset cradle to its base.
2. Position the handset cradle on the left side of the fax machine.
24 User’s Guide
3. Plug one end of the handset cable into the handset. Then plug the
other end of the handset cable into the socket located on the front of
the cradle. Place the handset in the cradle.
4. Insert the supplied telephone cable into the socket located on the
back of the cradle.
5. Feed the telephone cable from the back of the cradle through the
cable run located on the back of the fax machine.
6. Insert the other end of the telephone cable into TEL1 or TEL2
sockets on the back of the fax machine.
Connecting external telephone or answering machine
1. Insert one end of the telephone cable into the TEL terminal on the
back of the machine.
2. Insert the other end of the telephone cable into the socket in your
external device.
Note 1:
To connect both an answering machine and a
telephone, first connect your answering machine to
your fax machine, then insert the cable of your
external telephone into the telephone socket on your
answering machine.
Installation 25
English
Note 2:
You will need to have the TAD mode feature turned
on for an answering machine to work with your fax
machine. See Setting Answering Mode in
Installation.
Connecting power
1. Make sure the power switch is in the OFF position (the 0 should be
pressed down).
2. Insert the power cable into the power inlet socket located on the
back of the fax machine.
3. Connect the unattached end of the power cable into an eathed AC
power outlet.
4. Turn the power switch on (the I should be pressed down). Your fax
machine will take a few moments to warm up.
5. The time and current answering mode will appear on the display.
Your fax machine is now in standby mode, ready to send or receive
faxes.
26 User’s Guide
Loading paper
Your fax machine can hold up to 250 sheets of standard-weight (80 g/m
2
)
paper. For best results, use paper specially made for laser printers or
photocopiers. Available sizes are A4, letter size and legal size.
Your fax machine automatically reduces the vertical length of the page
images it receives to fit on the paper loaded in your fax machine (down to
75% of the original length). For example, if a document created originally
on legal-size paper is received, your fax machine reduces the received
pages to fit on A4 or letter-size paper.
Note: Your fax machine is set at the factory to use A4
paper. If you intend to use a different paper size,
change the 1’ST PAPER SIZE user function setting to
match your new paper size. See Programming later
in this user’s guide.
1. Pull the paper cassette out of the fax machine.
2. Adjust the paper guides to the width of your paper.
3. If necessary, lift and adjust the vertical paper guide for the length of
your paper.
Installation 27
English
4. If you are using legal size paper, pull out the extension at the back
of the paper cassette.
5. Remove the paper from its wrapper (up to 250 sheets). Note the
“print side” notice printed on the label. Fan the paper.
6. Load the paper into the cassette, print side down.
Note:
Be sure the paper is under the tabs at the left and
right edges of the cassette. Do not fill past the Paper
Full marker. If necessary, readjust the guides for a
snug (but not tight) fit.
7. Return the tray to the slot. Push it forward until it locks.
28 User’s Guide
Setting time & date
Follow these instructions to set the time and date on your fax machine.
1. Press the Select Function key.
2. Press the 9/User Program One Touch key.
3. On the numeric keypad, press 3. The display will show 3:CLOCK
ADJUSTMENT.
4. Press the YES key. The display will show the currently set date and
time.
5. Using the numeric keypad, enter the new date and time.
6. Press the YES key to confirm your entry.
7. Press the Select Function key to finish.
Setting answering mode
Your fax machine has a number of answering modes which determine how
it handles incoming calls (both fax and voice). The current answering
mode appears on the LCD panel of your fax machine.
Answering mode options
The answering mode which is best for you will vary depending on how
you use your fax machine and what external telephone devices are
connected to it. Read through the answering modes listed here, then follow
the instructions below.
Auto Receive Mode [FAX]:
If your fax machine is connected to a
telephone line reserved only for fax communications, use the Auto
Receive mode. Your fax machine will assume all incoming calls are fax
messages and automatically receive all incoming fax messages.
Manual Receive Mode [TEL]:
If you use the same line for both fax and
telephone calls and the majority of your incoming calls are telephone calls,
then the TEL answering mode is your best choice. Each time someone
calls, your fax machine rings like a telephone. You can answer from either
an external handset or from an external telephone connected to your fax
machine. If you pick up the handset and hear fax machine tones (normally
a short peep every three seconds), press the Start key to receive the fax. If
Installation 29
English
you do not answer the telephone and someone tries to send you a fax
message, your machine will not accept it.
Telephone/Fax Auto Switch Mode [T/F]:
When incoming calls are a
mixture of fax and telephone calls, your best choice is the Telephone/Fax
Auto SW mode. In this mode, your fax machine detects whether the
incoming call is a fax or voice call. When the call is from another fax
machine, your machine will switch to fax mode and receive the message.
When the call is a voice call, your fax machine will ring like a telephone.
If you do not answer, your fax machine will switch back to fax mode to
allow the calling party to manually send a fax.
Telephone Answering Device Mode [TAD]:
Use this mode if you have
connected an answering machine to your fax machine. When a call is
received and is not answered, your answering machine activates and is
ready to send out your recorded outgoing message. At the same time, your
fax machine monitors the incoming call to check if the call is a fax or voice
call. If the incoming call is a fax call, your fax machine will receive the fax
and no voice message will be recorded on your answering machine. If teh
incoming call is a voice call, then your faqx machine will not activate and
the calling party will be able to leave a voice message on your answering
machine.
Note:
In some countries, the Telephone Answering Device
mode is normally turned off. To have it turned on,
contact your dealer.
Memory Reception Mode [MEM]:
Use this answering mode if you want
incoming faxes to be stored in the memory of your fax machine and not
immediately printed. You can then use the print function to print out any
messages that have been stored in memory.
Fax Forwarding Mode [FWD]:
When set to this mode, your fax
machine receives all fax messages into memory, and then automatically
re-sends the fax messages to the forwarding number programmed into
your fax machine. For information on setting the forwarding number, refer
to Setting Forwarding Number in Installation.
PC Interface Mode [PC]:
If you have purchased the optional PC
Interface Board for your fax machine, this mode turns on the connection
between your fax machine and a personal computer. Refer to the
documentation you received with your PC Interface Board option for
details.
30 User’s Guide
Changing answering mode
Follow these instructions to change the answering mode on your fax
machine.
1. Press the Auto Rec key. Your fax machine displays your current
answering mode.
2. Press the Auto Rec key again. Your fax machine switches to the
next answering mode.
3. Continue pressing the Auto Rec key until the answering mode you
want appears on the display. After a short pause, your fax machine
programs the new answering mode and returns to standby mode
displaying the new answering mode setting.
Fax machine identification
Fax machines use the information you will enter here to identify
themselves during communications. In most countries programming this
information into your fax machine is a legal requirement. The information
you will enter here includes:
TSI/CSI:
This is the telephone number of your fax machine. This number
appears on displays and reports of other fax machines you are
communicating with. This number may also be printed at the top of faxes
you send to other fax machines.
Sender ID:
This is a descriptive title and is usually the location of your fax
machine or the name of your company or office. The Sender ID is printed
at the top of every fax you send. You can enter up to 32 characters. The
first 16 characters of your Sender ID will also be used as your Personal ID,
which may appear on the displays or reports of other fax machines you are
communicating with.
Call Back Number:
The Call Back Number is a telephone number (not a
fax number) which the operator of the remote machine can use to reach
you. If you use the voice request function while you are transmitting to
another fax machine and no one is there to answer, your fax machine will
automatically send a cover letter with a call back message. The call back
message is printed in a separate sheet with the message “Please call back”
and a telephone number where you can be reached. The call back number
entered here is the number that appears on the call back message.
Installation 31
English
Setting fax machine identification
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. On the numeric keypad, press 4. The display shows 4:SYSTEM
DATA PRG.
4. Press the YES key. The display shows NO=<TSI/CSI>,
ID=<SENDER ID>.
5. After the display clears, enter the full telephone number of your fax
machine using the numeric keypad.
Note:
Use the Hyphen key to enter a “+” character before
the number, which is the generally recognised
method of indicating the international access code
before the country dialling code. The Space One
Touch key is used to enter spaces in a number.
6. Press the Start key to save your entry.
7. Enter your Sender ID. This is a descriptive title up to 32 characters
long. Refer to the instructions below.
8. Press the Start key to save your entry. The display shows
NO=<CALL BACK NO.>.
9. After the display clears, use the numeric keypad to enter the
telephone number you want to use for call back messages. Enter up
to 20 characters.
To Do This Use
Enter numbers Numeric keypad
Enter spaces Space One Touch key
Enter hyphens Hyphen key
Enter alphabet characters Locate the character you want on the numeric keypad.
Press that key repeatedly until the character appears.
Enter a unique character. Press the 0/Unique key repeatedly until the character
you want appears. The following characters are
available: ! # & ‘ ( ) * + , - . / : ; = ? _ ä ¤ ñ ö ü Æ Å Ø
æ å ø.
Enter next character Press the NO key to move the cursor to the next
position for the next character.
Move the cursor to make corrections YES and NO keys.
32 User’s Guide
Note:
Use the Hyphen key to enter a “+” character before
the number, which is the generally recognised
method of indicating the international access code
before the country dialling code. The Space One
Touch key is used to enter spaces in a number.
10. Press the Start key to save your entry.
11. Press the Select Function key to finish.
Setting forwarding number
When the answering mode of your fax machine is set to Fax Forwarding
[FWD], it will receive fax messages into memory and then automatically
resend the faxes to the number which you enter here.
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. Using the numeric keypad, press 6. This display shows
6:FORWARDING NO. PRG.
4. Press the YES key. The display will show NO=<FORWARDING
NO.>.
5. After the display clears, enter the fax number to which you want
your messages forwarded.
6. Press the Start key to save your entry.
7. Press the Select Function key to finish.
To Do This Use
Enter numbers Numeric keypad
Enter spaces Space One Touch key
Enter hyphens Hyphen key
Enter pauses (i.e., to wait for long
distance or outside lines)
Pause key
Add a switch from pulse to tone
dialling for part of the call
*/Tone key
Move the cursor to make corrections YES and NO keys.
Installation 33
English
Setting language
Your fax machine comes with two languages installed, which appear on
the display and in reports. Follow the instructions below to switch
languages.
Note:
Your dealer may be able to provide you with
additional languages.
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. Press the YES key. The display shows FUNCTION NO. [ ].
4. Using the numeric keypad, enter 15. The display shows 15:USER
LANGUAGE.
5. Press the NO key to switch to the other installed language.
6. To accept the language change, press the YES key.
7. Press the Select Function key to finish.
Connecting to a PBX
A PBX (Private Branch Exchange) is a private telephone system used to
route internal calls. If you have to dial a prefix (access) number to get an
outside line, then your line is connected to a PBX.
If you are connecting your fax machine to a PBX, follow the instructions
below. These setting changes allow your fax machine to identify the
numbers of the prefix digits required to dial an outside line on your PBX.
After it dials the prefix digits, your fax machine will wait until it sees that
the outside line is available before dialling the rest of the number.
Note:
In some countries you may require service assistance
to make these changes. Also, some PBX installations
may require additional adjustments to your fax
machine. If you continue to have difficulty with fax
communication after following these steps, contact
your dealer.
1. Press the Select Function key.
34 User’s Guide
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. On the numeric keypad, press 2. The display shows 2:DIAL
PARAMETER.
4. Press the YES key until the display shows PBX LINE, [OFF].
5. Press the NO key. The display changes to PBX LINE, [ON].
6. Press the YES key until the display shows DIAL PREFIX, [OFF].
7. Press the NO key. The display changes to DIAL PREFIX, [ ]
ENTER 4DIGITS.
8. Using the numeric keypad, enter the number you normally dial
from your PBX to obtain an outside line.
9. Press the Space One Touch key until the display changes.
10. Press the YES key.
11. Press the Select Function key to finish.
Note 1:
The DIAL PREFIX number of your PBX LINE must
be included in all outside telephone numbers you
program into your fax machine or dial with the
numeric keypad.
Note 2:
To later turn off the PBX LINE and DIAL PREFIX
functions, follow Steps 1 - 7 above. At Step 8, press
the Space key four times, then continue with Steps 10
- 11.
Dial Directories 35
English
Dial Directories
One touch keys
Programming
Your fax machine has 30 One Touch keys for rapid dialling. You can store
up to two fax numbers with 32 digits for each One Touch key, a main
number and an alternate number. The alternate number is be used if the
main number is busy. You can also enter a 15 character Location ID
(name) for each One Touch key.
Note:
To program or use One Touch keys 16 to 30, grasp
the One Touch keypad latch and swing the main One
Touch panel out of the way. You can then select from
One Touch keys 16 to 30. When you are finished,
close the One Touch keypad to continue.
1. Press the Select Function key, then press the 8/Location Program
One Touch key. The display shows LOCATION PROGRAMMING.
2. Press a One Touch key to program and the display briefly shows
NO=<FAX NO.>, ID=<LOCATION ID> or a
previously-programmed fax number and Location ID.
36 User’s Guide
3. Enter the main fax number as follows:
4. Press the Start key.
5. Enter the Location ID. This is a descriptive title up to 15 characters
long. Refer to the instructions below.
6. Press the Start key. The display shows NO=<OR LOCATION>.
7. Enter the alternate fax number. Refer to the instructions following
Step 3.
8. Press the Start key to finish programming the One Touch key. The
display shows LOCATION PROGRAMMING.
9. To continue programming One Touch keys, go back to Step 2. If
you are finished programming, press the Select Function key.
10. Lift off the plastic cover above the One Touch label. Using a pencil,
write in the name for your newly-programmed One Touch key.
Replace the cover.
To Do This Use
Enter numbers Numeric keypad
Enter spaces Space One Touch key
Enter hyphens (i.e. to wait for dial
tone)
Hyphen key
Enter pauses (i.e., to wait for outside
lines)
Pause key
Add a switch from pulse to tone
dialling for part of the call
*/Tone key
Move the cursor to make corrections YES and NO keys.
To Do This Use
Enter numbers Numeric keypad
Enter spaces Space One Touch key
Enter hyphens Hyphen key
Enter alphabet characters Locate the character you want on the numeric keypad.
Press that key repeatedly until the character appears.
Enter a unique character. Press the 0/Unique key repeatedly until the character
you want appears. The following characters are
available: ! # & ‘ ( ) * + , - . / : ; = ? _ ä ¤ ñ ö ü Æ Å Ø
æ å ø.
Enter next character Press the NO key to move the cursor to the next
position for the next character.
Move the cursor to make corrections YES and NO keys.
Dial Directories 37
English
One touch parameters
If you are experiencing problems communicating with a remote location
in a very noisy telephone area, set up a One Touch key for that location and
try turning Echo Protection on for that One Touch key.
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. Press the YES key. The display shows FUNCTION NO. [ ].
4. Using the numeric keypad, enter 23. The display shows 23:ONE
TOUCH PARAM.
5. Press the One Touch key for the location whose settings you want to
change. The display shows ECHO PROTECTION, [OFF].
6. Press the NO key to switch Echo Protection on.
7. Press the YES key to confirm your selection.
8. Press the Select Function key to finish.
Note:
Should you later change the location the One Touch
key is used for, then remember to switch Echo
Protection off.
Chain dialling
Each fax number that you enter or program into your fax machine can be
up to 32 digits long. In the case that you need to dial a number which is
longer than 32 digits, then you can use the chain dial feature.
To create a chain dial number, program the first 31 digits of the number
into a One Touch key or Auto Dial number. Then press the Plus One Touch
key to make this is a chain dial number. Next, program the rest of the
number into another One Touch key or Auto Dial number. You can, if so
desired, leave teh second part of the number unprogrammed and enter it
manually on the numeric keypad.
To use a chain dial number, select the One Touch key or Auto Dial number
programmed with the first part of the chain dial number. The display will
show PRESS OT/AD/SRCH KEY. Then select the One Touch key or Auto
Dial number programmed with the second part of the chain dial number.
If the second part of the chain dial number was not programmed, enter it
38 User’s Guide
manually on the numeric keypad. Press the Start key to begin sending the
fax.
Auto dial numbers
Programming
Your fax machine has 99 Auto Dial numbers available for quick, two-digit
selection and dialling. For each Auto Dial number, you can enter a fax
number up to 32 digits long and a Location ID (name) up to 15 characters
long.
1. Press the Select Function key, then press the 8/Location Program
One Touch key. The display shows LOCATION PROGRAMMING.
2. Press the Auto Dial key.
3. Using the numeric keypad, enter a 2-digit number for the Auto Dial
number (01 to 99) you want to program.
4. The display will briefly show NO=<FAX NO.>, ID=<LOCATION
ID> or a previously-programmed fax number and location.
5. Enter the fax number. Refer to the instructions below.
6. Press the Start key.
7. Enter the Location ID. This is a descriptive title up to 15 characters
long. Refer to the instructions below.
To Do This Use
Enter numbers Numeric keypad
Enter spaces Space One Touch key
Enter hyphens (i.e. to wait for dial
tone)
Hyphen key
Enter pauses (i.e., to wait for outside
lines)
Pause key
Add a switch from pulse to tone
dialling for part of the call
*/Tone key
Move the cursor to make corrections YES and NO keys.
To Do This Use
Enter numbers Numeric keypad
Enter spaces Space One Touch key
Enter hyphens Hyphen key
Enter alphabet characters Locate the character you want on the numeric keypad.
Press that key repeatedly until the character appears.
Dial Directories 39
English
8. Press the Start key to finish programming the One Touch key. The
display shows AUTO DIAL NO. [ ].
9. To continue programming Auto Dial numbers, go back to Step 3. If
you are finished programming, press the Select Function key.
Note:
If you want to delete any programming for a Auto
Dial key, follow Steps 1 - 4. At Step 5, press the Space
key until the number is deleted, then continue with
Steps 8 - 9.
Groups
Programming
Once you have programmed some One Touch keys or Auto Dial numbers,
you can then program these numbers into groups to allow you to send the
same fax to multiple locations.
1. Press the Select Function key, then press the 8/Location Program
One Touch key. The display shows LOCATION PROGRAMMING.
2. On the numeric keypad, press the # key. The display shows GROUP
SETTING.
3. Using the numeric keypad, enter the group number (01 - 20) you
want to program.
4. The display shows the number of your current group and SELECT
LOC.(S). You can now add a location to your group (or delete a
location from it). Refer to the instructions below.
Enter a unique character. Press the 0/Unique key repeatedly until the character
you want appears. The following characters are
available: ! # & ‘ ( ) * + , - . / : ; = ? _ ä ¤ ñ ö ü Æ Å Ø
æ å ø.
Enter next character Press the NO key to move the cursor to the next
position for the next character.
Move the cursor to make corrections YES and NO keys.
To Do This Use
Add a One Touch location Press the One Touch key. Press YES to add it to the
group.
To Do This Use
40 User’s Guide
5. After you have completed your selection (by pressing YES or NO),
the display again shows SELECT LOC. again. Continue to add or
delete locations from your group. Each group can contain up to a
maximum of all of the One Touch and Auto Dial locations available
on your fax machine.
6. When you are finished programming your group, press the NO key.
The display shows LOCATION PROGRAMMING.
7. To program another group, go back to Step 2. If you are finished,
press the Select Function key.
Add Auto Dial location Press Auto Dial. Enter the 2-digit Auto Dial number.
Press YES to add it to the group.
Delete One Touch location Press the One Touch key. Press NO to delete it from
the group.
Delete Auto Dial location Press the Auto Dial key. Enter the 2-digit Auto Dial
number. Press NO to delete it from the group.
Search for a location name to add or
delete
Press the Search key continuously until by the location
you want appears. Press YES to add it to the group.
Press NO to delete it.
To Do This Use
Basic Operations 41
English
Basic Operations
Preparing documents
• Try to use good quality documents for your transmissions.
Documents that are typed or created in felt-tip black ink on white
(or light) paper work best.
• Do not send documents which are not rectangular.
• Never use documents that have wet or sticky surfaces, wrinkles,
staples or paper clips. However, your fax machine can transmit
documents that have been subject to normal wear, such as
documents with staple holes, letter folds and minor corner folds.
• If you are not sure how a document will fax, try making a copy first
on your fax machine (load the document face down and press the
Copy key).
• If your documents are extremely bent, creased or torn, make a copy
on a photocopier and send the copy instead. You can also use a
photocopier to enlarge or reduce documents before sending.
Document size
All documents must have a minimum width of 148 mm and a minimum
length of 128 mm. Documents cannot be wider than 216 mm or longer than
356 mm.
Multiple page documents
Your fax machine can scan paper with a base weight between 50 g/ m
2
and
105 g/m
2
. You can load up to 20 sheets of standard 80 g/ m
2
paper (e.g.
photocopier paper) at the same time. If you use a heavier paper, you can
load up to 15 sheets. For very heavy paper, load and send pages
sheet-by-sheet.
42 User’s Guide
When loading multiple-page documents, do not load paper which is
thinner than 0.08 mm or thicker than 0.13 mm. For documents, do not load
paper which is thinner than 0.06 mm or thicker than 0.15 mm.
Loading documents
To prevent paper jams and problems during scanning, neatly stack your
documents, aligning their edges, before loading. Do not load documents of
different sizes at the same time.
Note:
You can load and prepare to transmit a document
while your fax machine is still sending or receiving
another message (as long as the document feeder is
clear). To do this, load the document, select your
location and press the Start key. Your document will
be sent when the current communication ends.
1. Adjust the document guides to the width of the paper you are using.
2. Neatly stack your documents, then insert them face down into the
document feeder. If necessary, readjust the document guides for a
snug fit.
3. Your fax machine will grip the documents, and pull the bottom page
into the machine.
Basic Operations 43
English
4. If necessary, use the Transmit Resolution/YES key to set the
resolution of your document.
5. If necessary, use the Type of Original/NO key to set the level of
contrast in your document.
6. Your documents are now ready for faxing or copying.
Sending faxes to single location
1. Load your documents.
2. Select a location. Refer to the instructions below.
3. If necessary, press the Start key to begin the transmission. Refer to
the table below to understand some of the messages you may see
during a typical fax transmission.
Document Type Resolution
Normal office documents STD (Standard)
Documents with small type or other fine details FINE or EX. FINE
Documents with photos or many shades of gray PHOTO
Document Type Contrast
Documents with normal contrast NORMAL
Documents which are too light LIGHT
Documents which are too dark DARK
To Dial Using Do This
One Touch key Press the One Touch key. Lift the main One Touch keypad to
access one Touch keys 16–30.
Auto Dial number Press the Auto Dial key, then enter the two digit Auto Dial
number on the numeric keypad.
Numeric keypad Dial as you would on a normal telephone. If you make a mistake,
press the YES key to go back and re-enter the number.
External telephone Pick up the handset of your external telephone and dial the
number of the machine you wish to transmit to. If the receiving
fax machine is in automatic reception mode, you will hear a high
pitched tone. If a person answers the phone, ask them to press the
Start key on their fax machine.
Message Explanation
(location) The Personal ID or TSI/CSI of the remote location. If this is not
prgrammed in the remote location, the Location ID or telephone
number you entered will identify the location during transmission.
DIALLING Your fax machine is dialling the number.
CALLING The line is ringing.
SENDING Your fax machine is sending the message.
44 User’s Guide
Search key dialling
If you are not sure which One Touch key or Auto Dial number contains the
location you want to communicate with, use the Search key to look
through an alphabetical list of all of the Location IDs programmed into
your fax machine.
1. When selecting locations, press the Search key. The display will
show ENTER 1-ST CHAR.
2. Repeatedly press the Search key to look through the entire list of
locations in alphabetical order, or locate the letter you want on the
numeric keypad, and press that key repeatedly to look through
Location IDs beginning with that letter.
Real-time dialling
Normally, your fax machine dials the entire number of the location you
have selected at one time. Occasionally, it may be necessary to dial
numbers in real time (one digit at a time).
If your fax machine is equipped with a handset, you can dial in real time
by picking up the handset or press the Hook/V. Request key.
Note:
Real-time dialling with the use of the Hook/V.
request key is not available in some countries.
Redialling
If the line is busy or if there is no answer, your fax machine waits and then
automatically redials the number. Also, if your fax machine is transmitting
from memory and a communication error occurs, it will automatically
redial the number and try to send the fax again. You can redial a number
manually at any time by pressing the Redial key.
RESULT = OK The fax was sent successfully.
COMMUN. ERROR If you see this or another error message, a problem occurred during the
communication. Try resending the fax. Refer to Problem Solving for
assistance.
Message Explanation
Basic Operations 45
English
Confirming results
After transmission, press the Copy key once (with no documents loaded)
to see a report confirming your transmission on your fax machine’s
display. To print the report, press the Copy key a second time. See Reports
for more information.
Stopping transmissions
To stop a transmission while it is in progress, follow the instructions
below.
1. Press the Stop key twice. The display will show STOPPED.
2. If documents are stuck part way through the document feeder, you
may see the following message on the display RELOAD
DOCUMENT. Press the STOP key again. Your fax machine feeds
the document the rest of the way through the document feeder.
Note:
If your fax machine cannot feed your document
through the document feeder, refer to Problem
Solving.
Receiving faxes manually
Your fax machine receives faxes automatically unless the fax machine has
been set to the manual receive [TEL] mode. If your fax machine is set to
the manual receive [TEL] mode, follow the instructions below.
1. When your telephone or fax machine rings, pick up the telephone
handset. If the call is a voice call, start speaking to the caller.
2. If the call is a fax call, or if a person wishes to fax you a document
after having a conversation, press the Start key and hang up the
handset.
3. After you receive the fax, a long beep will tell you that the
transmission was successful.
46 User’s Guide
Receiving faxes into memory
Your fax machine automatically receives messages into memory and does
not immediately print them in the following situations.
Memory reception
When your fax machine has been set to Memory Reception mode [MEM],
any received faxes are stored in the memory of your fax machine and are
not automatically printed. The display shows MSG. IN MEMORY if any
faxes have been received during memory reception mode.
When you change the reception mode of your fax machine, any non-
confidential fax messages stored in memory are automatically printed.
No paper reception
When your fax machine has run out of paper, a MSG. IN MEMORY,
REPLACE PAPER message appears on the display. Your fax machine
continues to receive faxes into memory when it has run out of paper. Your
fax machine automatically prints out any messages received in memory
when the paper is replaced and the Stop key is pressed.
Note:
You can also print out these messages using the
method described in No Toner Reception, below.
No toner reception
When your fax machine is running low on toner, it displays a TONER
LOW, REPLACE TONER CART. message. Rather than risk printing an
unreadable message, your fax machine automatically receives faxes into
memory.
If your fax machine has received a message in memory because toner is
low, MSG. IN MEMORY appears on the display. To print out a message
stored in memory when toner is running low, follow the instructions
below.
1. Press the Select Function key.
2. Press the 10/Message Print From Memory One Touch key. The
display shows 1:PRINT MEMORY MSG.?
Basic Operations 47
English
3. Press the YES key. The display shows FUNCTION NO. [ ].
Note:
Even if you see a TONER LOW message on your fax
machine, you may be able to use the 10/Message
Print From Memory One Touch key to continue
printing faxes, but the print quality cannot be
guaranteed. Replace your toner cartridge as soon as
possible.
Cancelling messages stored in memory
It is also possible to erase messages received in memory without printing
them.
1. After you have followed the instructions to print out messages
stored in memory, the display shows MESSAGE IN MEMORY,
PRINTING.
2. To erase the message instead of printing it, press the Stop key. The
display shows CANCEL?
3. Press the YES key to erase the message from the memory of your
fax machine.
Rejecting unsolicited fax messages
The closed network option allows you to limit the locations your fax
machine can communicate with. Using this function, you can set your fax
machine to refuse to receive any faxes from locations whose telephone
numbers are not programmed into your One Touch keys or Auto Dial
numbers. Use of this function allows you to reject any unsolicited faxes
such as advertising.
Note:
In some countries, this function cannot be set by the
user. Please contact your dealer for assistance.
You can also set your fax machine not to send faxes to locations whose
telephone numbers are not programmed into your One Touch keys or Auto
Dial numbers.
48 User’s Guide
The available settings are limit reception only (RX), limit both
transmission and reception (T/R), and no limitation on transmission or
reception (OFF). To use the closed network function, follow the
instructions below.
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. Press the YES key. The display shows FUNCTION NO. [ ].
4. Using the numeric keypad, enter 08. The display shows
08:CLOSED NETWORK, and the current setting of this function.
5. Press the NO key until the setting you want appears in the display.
6. Press the YES key to confirm the new setting.
7. Press the Select Function key to finish.
Power failures & memory
If power is interrupted to your fax machine, the following problems will
occur:
• Any messages your fax machine has scanned into memory, but not
yet transmitted, are lost.
• Any messages your fax machine has received into memory, but not
yet printed, are lost.
• If you have loaded documents onto the document feeder of your fax
machine, any dialling or transmission settings are lost.
Your fax machine prints a power outage report to inform you of a power
failure. Use this report to determine which received messages you may
have lost and which transmissions you may have to resend. Refer to
Reports for more information.
Making copies
Your fax machine can also be used to make copies. You can make up to 50
copies at one time. Your fax machine automatically makes all copies in
FINE mode. EX.FINE and PHOTO mode can be selected manually by
pressing the YES key.
1. Load your documents.
Basic Operations 49
English
2. Press the Copy key. The display shows PRG. NO. OF COPIES,
[1SETS]. If you want to make just one copy, you are finished. Your
fax machine waits a moment, then begins copying.
3. To make multiple copies, enter the number of copies you want to
make on the numeric keypad. Then press the Copy key again. Your
fax machine begins making the required number of copies.
Making copies using manual paper feeder
The manual paper feeder of your fax machine allows you to make copies
on a different type of paper than what is normally kept in the paper tray of
your fax machine. To make copies using the manual paper feeder, follow
the instructions below.
1. Load your documents.
2. Press in on the lower half of the front panel indents, just above the
paper cassette.
3. Pull the manual paper feeder down until it is horizontal.
50 User’s Guide
4. Adjust the paper guides on the manual paper feeder.
5. Insert a sheet of paper face up, adjusting the guides again to ensure
the paper is straight.
6. Press the COPY key.
Note:
It is recommended to make single copies only when
using the manual paper feed slot. This will prevent
any possible paper feed jams from occurring.
Using voice request
The voice request feature allows you to have a conversation with a person
at a remote fax machine during a fax communication. Either the sender or
receiver can initiate a voice request.
If you are sending a fax, you can answer a voice request only after all pages
have been transmitted. If you are receiving a fax, you can answer a voice
request after reception of each page.
You will know if the person on the other fax machine has issued a voice
request when you hear a warbling tone. If you do not respond in
approximately six seconds, the voice request is automatically cancelled.
Basic Operations 51
English
Note:
You will need to have either an attached handset or
an external telephone to use the voice request
function.
Initiating voice request
1. During a fax communication, press the Hook/V. Request key.
2. When the other party answers your request, your fax machine will
emit a repetitive warbling sound. The display shows LIFT
HANDSET AND PRESS VOICE REQUEST.
3. Lift your handset and press the Hook/V. Request key.
Note 1:
If you press your Hook/V. Request key to initiate a
voice request during transmission, but no one is
there to answer, your fax machine automatically
sends a call back message to the remote site giving a
telephone number where you can be reached.
Note 2:
A call back message is only sent if you have
programmed a call back number into your fax
machine. Refer to Setting Fax Identification.
Note 3:
The voice request feature is not available if you have
sent the fax message from memory.
Answering voice request
1. Lift the handset and press the Hook/V. Request key.
52 User’s Guide
Advanced Operations 53
English
Advanced Operations
Sending faxes to multiple locations
If you want to send the same fax to more than one location, carry out the
following steps:
1. Load your documents.
2. Press the Select Function key.
3. Press the 2/Broadcast Memory TX One Touch key. The display
shows BROADCAST/MEMORY TX.
4. Select a location. Refer to the instructions below.
5. Press the YES key to confirm your selection.
6. Repeat Steps 4 and 5 as often as necessary to continue selecting
locations.
7. When you are finished selecting locations, press the NO key at the
SELECT LOCATION(S) message.
8. If you have selected multiple locations, your fax machine will ask if
you want to confirm your selections with a printed report before
proceeding. Press the YES key. After the report is printed, the
display will show BEGIN SCANNING? If you want to make
corrections, press the NO key and go back to Step 4. To remove a
location, select the location in the same way, but press the NO key
to delete it from your transmission.
To Select Using Do This
One Touch key Press the One Touch key. Lift the main One Touch
keypad to access One Touch keys 16 to 30.
Auto Dial number Press the Auto Dial key, then enter the two digit
Auto Dial number on the numeric keypad.
A group Using the numeric keypad, press the # key, then
enter the number of the group youo want to use.
A number dialled on the numeric keypad Dial as you would on a normal telephone.
54 User’s Guide
9. When all of your selections are correct, press the Start key. Your fax
machine will scan the documents into memory and begin
transmitting the message.
Delayed sending of faxes
The delayed transmission feature allows you to send documents at a
specified date and time, and frees you from the need to manually start the
transmission. You can program a delayed transmission to occur at any time
on the day of your transmission, or at any time over the next three days.
You can send a delayed fax either from the document feeder or from
memory. Refer to the table below to decide which method you want to use.
Sending delayed fax from document feeder
1. Load your documents.
2. Press the Select Function key.
3. Press the 1/Delayed TX One Touch key. The display shows
DELAYED TX and today’s date.
4. If transmission is to occur today press YES key and go to step 7. If
transmission is to occur at a later date press the NO key.
5. Using the numeric keypad, enter the date on which you wish the
transmission to begin.
6. Press the YES key. The display shows PRG. START TIME.
7. Using the numeric keypad, enter the time on which you wish the
transmission to begin.
Note:
Enter the time using a 24-hour clock, i.e., 8:00 a.m.
would be entered as 08:00 and 8:00 p.m. would be
entered as 20:00.
Delayed TX Features & Limitations From Feeder From Memory
Number of locations One Multiple
Number of delayed faxes in your fax machine at any one
time
One Up to twenty
Fax machine can be used for other transmissions while
adelayed fax is waiting to be sent?
No Yes
Advanced Operations 55
English
8. Press the YES key and the display shows BROADCAST/
MEMORYT/X or FEEDER TX depending on the User Function 18
setting.
9. If display shows FEEDERTX go to step 10. If display shows
BROADCAST/MEMORYTX press the NO key. The display shows
FEEDERTX.
10. Select a location. Refer to the instructions below.
11. Press the Start key. Your fax machine then waits for the time and
date you have set before sending the fax.
Sending delayed fax from memory
1. Load your documents.
2. Press the Select Function key.
3. Press the 1/Delayed TX One Touch key. The display shows
DELAYED TX and today’s date.
4. If transmission is to occur today press YES key and go to step 7. If
transmission is to occur at a later date press the NO key.
5. Using the numeric keypad, enter the date on which you wish the
transmission to begin.
6. Press the YES key. The display shows PRG. START TIME.
7. Using the numeric keypad, enter the time on which you wish the
transmission to begin.
Note:
Enter the time using a 24-hour clock, i.e., 8:00 a.m.
would be entered as 08:00 and 8:00 p.m. would be
entered as 20:00.
8. Press the YES key and the display shows BROADCAST/
MEMORYT/X or FEEDER TX depending on the User Function 18
setting.
To Select Using Do This
One Touch key Press the One Touch key. Lift the main One Touch
keypad to access One Touch keys 16 to 30.
Auto Dial number Press the Auto Dial key, then enter the two digit
Auto Dial number on the numeric keypad.
A number dialled on the numeric keypad Dial as you would on a normal telephone.
56 User’s Guide
9. If display shows BROADCAST/MEMORYTX go to step 10. If
display shows FEEDERTX press the NO key. The display will
show BROADCAST/MEMORYTX.
10. Select a location. Refer to the instructions below.
11. Press the YES key to confirm your selection.
12. Repeat Steps 10 and 11 as often as necessary to continue selecting
locations.
13. When you are finished selecting locations, press the NO key at the
SELECT LOCATION(S) message.
14. If you have selected multiple locations, your fax machine asks if
you want to confirm your selections with a printed report before
proceeding. Press the YES key. After the report is printed, the
display shows BEGIN SCANNING? If you want to make
corrections, press the NO key and go back to Step 10. To remove a
location, select the location in the same way, but press the NO key
to delete it from your transmission.
15. When all of your selections are correct, press the Start key. Your fax
machine scans the documents into memory and then waits for the
time and date you have set before sending the fax. When scanning
is completed, your fax machine becomes available for other
transmission operations.
Cancelling delayed transmissions
To cancel a delayed transmission from the document feeder or from
memory before it has been sent, follow the instructions below.
1. Press the Stop key. The display shows COMMUNICATION
CANCEL.
2. Press the YES key. The display shows the Location ID or telephone
number of the first delayed transmission currently loaded in your
fax machine.
To Select Using Do This
One Touch key Press the One Touch key. Lift the main One Touch
keypad to access One Touch keys 16 to 30.
Auto Dial number Press the Auto Dial key, then enter the two digit
Auto Dial number on the numeric keypad.
A group Using the numeric keypad, press the # key, then
enter the number of the group youo want to use.
A number dialled on the numeric keypad Dial as you would on a normal telephone.
Advanced Operations 57
English
3. Press the YES key to cancel the delayed transmission that is
displayed. If more than one delayed transmission has been
programmed into your fax machine, press the NO key until the
location of the delayed transmission you want to cancel appears,
then press the YES key to cancel.
4. If the delayed transmission was a feeder transmission, press the
Stop key again to remove the document from the document feeder.
Confidential faxes
Fax machines are often placed in public places where anyone can look
through received faxes. To overcome this, use the confidential fax feature
when sending and/or receiving confidential faxes.
You can send and receive confidential faxes to/from other Okifax
machines with personal mail boxes. However, the International
Telecommunications Union (ITU) has now created a worldwide standard
that uses ITU sub-addressing to allow fax machines or PC fax software
from different manufacturers to send and receive confidential faxes.
When sending confidential faxes, you must know in advance the mail box
number, or ITU sub-address, of the recipient you are sending the message
to. Ask the person who is receiving the fax to tell you their mail box
number, or ITU sub-address.
A receiving fax machine stores the message in a confidential mail box or
ITU sub-address protected by a password and will not print any
confidential faxes until the correct password is entered.
Sending confidential faxes
1. Load your documents.
2. Press the Select Function key.
3. Press the 3/Confidential TX One Touch key. The display will ask
you to enter the number of a confidential mail box, or ITU sub-
address, on the receiving fax machine.
4. Using the numeric keypad, enter the number of the confidential
mail box you are transmitting to.
5. Press the YES key to confirm your entry. The display shows
SELECT LOCATION.
58 User’s Guide
6. Select your location as follows.
Note:
You cannot send a confidential fax to a group or
multiple individual locations.
7. Press the Start key and your fax machine will begin sending the fax.
Receiving confidential faxes
Before you can receive confidential faxes, you have to create a
confidential or personal mailbox on your fax machine that is password
protected (see below). You then have to tell the person sending the
confidential fax your mailbox number
When your fax machine receives a confidential message, it will store the
message unprinted in the mailbox (in memory) until you enter a password.
Your fax machine can have a maximum of 16 mailboxes.
Creating confidential mailbox
Create a confidential or personal mailbox on your fax machine as follows:
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. Using the numeric keypad, press 5. The display shows 5:MAIL
PASSWORD PRG.
4. Press the YES key. The display shows MAIL BOX NO. [ ].
5. Using the numeric keypad, enter the two digit number of the mail
box you want to use.
Note:
If the mail box has been previously programmed and
a message is currently stored in the mail box, the fax
machine will not allow you to access the mail box. An
To Select Using Do This
One Touch key Press the One Touch key. Lift the main One Touch
keypad to access One Touch keys 16 to 30.
Auto Dial number Press the Auto Dial key, then enter the two digit
Auto Dial number on the numeric keypad.
A number dialled on the numeric keypad Dial as you would on a normal telephone.
Advanced Operations 59
English
ILLEGAL OPERATION message will appear. Print
out any messages stored in the mail box before
making changes to the mail box.
6. Using the numeric keypad, enter the 4-digit password you want to
use with your mail box.
7. Press the YES key to confirm your entry.
8. Your fax machine will ask you to enter another mail box number. To
continue programming mailboxes, go back to Step 5. If you are
finished programming, press the Select Function key.
Changing password or closing mailbox
If you want to change the password of an existing mail box, or if you want
to close an existing mail box, follow the instructions below.
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. Using the numeric keypad, press 5. The display shows 5:MAIL
PASSWORD PRG.
4. Press the YES key. The display shows MAIL BOX NO. [ ].
5. Using the numeric keypad, enter the two digit number of the mail
box whose password you want to change, or which you want to
close. The display shows PRG. PASSWORD.
6. Using the numeric keypad, enter the 4-digit password currently
used with that mail box.
7. Press the NO key. The display shows PRG. PASSWORD again.
8. To create a new password, enter a new 4-digit number on the
numeric keypad. To close a mailbox, press the Space One Touch
key.
9. Press the YES key to accept the new password or close the mail
box.
10. Your fax machine asks you to enter another mail box number. To
continue programming mailboxes, go back to Step 5. If you have
finished programming, press the Select Function key.
60 User’s Guide
Printing confidential faxes
Each time your fax machine receives a confidential fax, it automatically
prints a confidential reception report telling you which mail box number
received the message. To print a confidential fax after your fax machine
has received it, follow the instructions below.
1. Press the Select Function key.
2. Press the 10/Message Print From Memory One Touch key. The
display shows PRINT CONF. RX MSG.?
3. Press the YES key. The display shows MAIL BOX NO. [ ].
4. Using the numeric keypad, enter the two digit number of the mail
box you want to print from. The display shows MAIL BOX NO.
[ ] YES or NO. Press the YES key.
Note:
If no message is stored in that mail box, the display
shows NO DATA IN MEMORY.
5. Using the numeric keypad, enter the 4-digit password for the mail
box you want to print from.
6. Press the YES key. The message begins printing.
Note:
If you want to clear the mail box without waiting for
printing, press the Stop key at this point. The display
changes to CANCEL. Press the YES key to clear the
mail box.
Relay broadcasting
Relay broadcasting is where one fax machine, which is the relay initiating
station, sends a document to another fax machine. The receiving fax
machine, which is the relay key station, then re-sends (broadcasts) the
document to a number of other locations.
Relay initiating station
Your fax machine can act as the relay initiating station which starts the
relay broadcast by sending the original documents. Before programming
Advanced Operations 61
English
your fax machine to initiate a relay broadcast, you will need to obtain the
following information from the operator of the fax machine you intend to
use as a relay key station:
Relay Password:
This is the 4-digit relay key word which is programmed
into the relay key station.
Relay Group Numbers:
These 2-digit numbers are the code numbers of
locations or groups of locations programmed into the relay key station.
Relay key station
The relay key station is the fax machine which receives the original fax
message and then automatically relays or broadcasts the message to other
remote fax machines. For this feature to be available, the relay key station
must be an OKIFAX OF-27, OKIFAX OF-38, or OKIFAX 2600 fax
machine.
Relay broadcast report
After a relay broadcast is completed, it is possible for the relay key station
to send a message back to your fax machine confirming the success of the
relay broadcast. For this function to work, the telephone number of your
fax machine must be programmed into the AUTO DIAL list of your fax
machine with the AUTO DIAL code number 99.
Initiating relay broadcasts
1. Load your document.
2. Press the Select Function key.
3. Press the 4/Relay Initiate TX One Touch key. The display shows
RELAY PASSWORD.
4. Press the NO key.
5. Using the numeric keypad, enter a 4-digit password which is the
same as the relay keyword programmed into the relay key station.
6. Press the YES key. The display shows REMOTE LIST NO.
7. Press the NO key.
8. Using the numeric keypad, enter a 2-digit number which
corresponds to a relay group programmed into the relay key station.
62 User’s Guide
9. Press the YES key and the display changes to SELECT
LOCATION.
10. Select the location of the relay key station as follows:.
11. Press the Start key. Your fax machine will begin sending the fax.
Polling
When you normally send faxes, you load your document into your fax
machine, select a location and, if required, press the Start key to begin
sending the document. However, sometimes it is more useful to be able to
simply load your document into your fax machine and set it to wait for the
another fax machine to call and collect the document. This is called setting
your fax machine to be polled, or polling transmission. Calling another fax
machine to receive documents someone else has loaded into their fax
machine is called polling reception.
There are two standards for polling. Standard polling is to an old standard
that is used by many, but not all manufacturers and ITU selective polling,
which is the latest standard. Your Okifax machine supports both standards.
ITU selective polling allows you to retrieve documents from individual
mailboxes or ITU sub-addresses from a fax machine that meets the
standard for ITU selective polling.
Polling transmission
1. Load your documents.
2. Press the Select Function key.
3. Press the 5/Polling One Touch Key. The display shows WAITING
TO BE POLLED.
To Select Using Do This
One Touch key Press the One Touch key. Lift the main One Touch
keypad to access One Touch keys 16 to 30.
Auto Dial number Press the Auto Dial key, then enter the two digit
Auto Dial code number on the numeric keypad.
A number dialled on the numeric keypad Dial as you would on a normal telephone.
Advanced Operations 63
English
Polling reception
When carrying out polling reception, the fax machine you are polling
should be able to carry out standard polling transmission or ITU polling
transmission.
1. With no documents loaded, press the Select Function key.
2. Press the 5/Polling One Touch key. The display shows POLLING
RX, SELECT LOCATION.
3. Select the location of the fax machine you are polling as follows:
4. Press the Start key. Your fax machine will begin polling the remote
fax machine.
Dual access
The advanced dual access feature of your fax machine allows you to load
and prepare documents for transmission while your fax machine is sending
or receiving another message, or automatically printing reports. This
feature increases your productivity and reduces the time you must spend
waiting for other operations to finish.
If you load a document on the document table and the display shows
SELECT LOCATION, then your fax machine is ready to allow you to
prepare for the next transmission.
While sending faxes
After your fax machine has finished scanning a document into memory
(and while it is transmitting from memory), you can do the following:
• Load another document and prepare it for transmission.
• Continue to load documents as long as there is memory available on
your fax machine. When the first transmission is complete, the next
fax is automatically sent.
• Make copies.
To Select Using Do This
One Touch key Press the One Touch key. Lift the main One Touch
keypad to access One Touch keys 16 to 30.
Auto Dial number Press the Auto Dial key, then enter the two digit
Auto Dial code number on the numeric keypad.
A number dialled on the numeric keypad Dial as you would on a normal telephone.
64 User’s Guide
While receiving faxes
While your fax machine is receiving a fax, you can:
• Load another document and prepare it for transmission.
• Continue to load documents as long as there is memory available on
your fax machine. When the first transmission is complete, the next
fax is automatically sent.
• Continue to receive faxes while earlier messages are being printed
if your fax machine has been set to memory reception mode.
While making copies
While your fax machine is making local copies, you can:
• Continue to receive faxes while copies are being printed if your fax
machine has been set to memory reception mode.
While printing reports
While your fax machine is automatically printing reports, you can:
• Continue to receive faxes while reports are being automatically
printed if your fax machine has enough memory available. When
the report has finished printing, your received fax message is then
printed.
• Continue to load documents as long as there is memory available on
your fax machine. After the report is printed, your fax is
automatically sent.
Programming 65
English
Programming
Customising features & operations
Many features and functions of your fax machine have settings which can
be changed to customize the operations of your fax machine. Because each
country has different regulations, you may not be able to access all of the
settings listed below. If you have trouble changing a setting, contact your
dealer for assistance.
Viewing your current settings
Follow these instructions to obtain a configuration report showing your fax
machine’s current settings.
1. Press the Select Function key.
2. Press the 6/Report Print One Touch key. The display shows
1:ACTIVITY REPORT.
3. Using the numeric keypad, press 4. The display shows
4:CONFIGURATION.
4. Press the YES key and the report will begin printing.
5. Press the Select Function key to finish.
User function settings
User function settings allow you to customize the general operation of
your fax machine. Refer to the list below to determine which settings you
may need to change, then refer to Changing User Function Settings to
make the change.
66 User’s Guide
Note:
Depending on local telephone regulations, some of
the following user function settings may not be
available.
User function settings list
01:MCF (SINGLE-LOC.):
This function automati-cally prints a
Message Confirmation Report after each single location transmission or
polling transmission. Available settings are on and off.
02:MCF (MULTI-LOC.):
This function automatically prints a Message
Confirmation Report after each multiple location transmission. Available
settings are on and off.
03:ERR REPORT (MCF):
This function automatically prints a Message
Confirmation Report each time an error occurs during a transmission or
polling reception operation. Available settings are on and off.
04:IMAGE IN MCF:
When a Message Confirmation Report is
automatically printed, this function adds a portion of the first page your fax
machine transmitted. This is printed at the bottom of the message
confirmation report. Available settings are on and off.
05:SENDER ID:
This function controls the printing of the Sender ID of
your fax machine on the faxes you send. When turned on, your Sender ID
will be printed on each page slightly outside the image area of your
document. When turned off, your Sender ID will not be printed.
06:MONITOR VOLUME:
This function sets the volume your fax
machine uses for telephone line monitoring sounds during dialling.
Available settings are low, high and off.
07:BUZZER VOLUME:
This function sets the volume of the various
beep and alarm tones your fax machine emits during operations. Available
settings are low, middle and high.
08:CLOSED NETWORK:
This function allows you to program your fax
machine to refuse to receive faxes from or transmit faxes to locations
whose telephone numbers have not been programmed into the One Touch
keys or Auto Dial numbers of your fax machine. Using this function, you
can set up a closed network of fax machines. If you do not want your fax
machine to transmit faxes to or receive faxes from locations outside your
network, select T/R. If you only want your fax machine to refuse to receive
faxes from outside your network, select RX. Available settings are OFF,
T/R and RX.
Programming 67
English
09:TX MODE DEFAULT:
This function allows you to change default
type of original, transmit and copy resolution settings of your fax machine.
Unless you select otherwise using the Transmit Resolution/YES or Type
of Original/NO keys, your fax machine is set to use the STD and
NORMAL settings. If you are constantly sending faxes which require
some other combination of transmission modes, use this function setting
to change the default transmission modes to any other combination of
settings. While you are programming, the new default combinations will
appear on the LEDs above the Transmit Resolution/YES or Type of
Original/NO keys.
10:T/F TIMER PROG.:
When set to the telephone/ fax answering mode,
your fax machine automatically distinguishes between incoming voice and
fax calls. If the incoming call is a voice call, your fax machine will ring to
tell you to pick up the handset. If you do not answer, your fax machine
automatically switches back to facsimile mode to allow the calling party
to send a fax. The T/F TIMER function controls how long your fax
machine waits before switching back to fax mode. Available settings are
20 seconds or 35 seconds.
11:RING RESPONSE:
This function controls how long your fax
machine waits before answering an incoming telephone call when your fax
machine is set to auto receive or telephone/fax auto switch answering
modes. The available settings are 1 ring, 5 seconds, 10 seconds, 15 seconds
or 20 seconds.
Note:
If your fax machine is set to telephone/fax auto switch
answering mode, it is recommended that you set ring
response to one ring.
12:RING PTRN. FOR FAX:
Distinctive ringing is a service offered by
some telephone services that allow you to have different numbers on one
line, each with its own distinctive ring. In this way, when you get an
incoming call, you can identify what number is being called by the ring
pattern. Your local telephone service can provide you with more
information about this service and if it is available. If available, this service
is usually offered as a monthly charge to your normal telephone bill.
Available settings are type 1, type 2 and off.
13:1’ST PAPER SIZE:
This function allows you to tell your fax machine
what size of paper you are using in the paper tray of your fax machine.
Available settings are A4, letter, legal 13 and legal 14.
68 User’s Guide
15:USER LANGUAGE:
This function allows you to switch between the
two languages programmed into your fax machine.
16:INCOMING RING:
This function controls the telephone ringing
sound your fax machine makes when a call comes in. Available settings
are on and off.
17:REMOTE RECEIVE:
When you receive an incoming call, this
function allows you to remotely tell your fax machine to switch from
telephone to fax mode to receive an incoming fax. To use this function, use
the keypad of a handset or an external telephone to enter the remote receive
number you have programmed into your fax machine. Available settings
are off, 00, 11, 22, 33, 44, 55, 66, 77, 88, 99, ** and ##. This function only
works if your telephone system is a tone dialling system.
18:MEM./FEEDER SW.:
This function controls how your fax machine
normally transmits fax messages to one location. Either scanning the
document into memory first and then start dialling, or by transmitting
directly from the document feeder after dialling. Available settings are
MEM. and FEED.
19:POWER SAVE MODE:
This function substantially reduces the
amount of power your fax machine consumes when it is not in use. When
this function is on, your fax machine automatically switches to power save
mode after it has been idle for three minutes. When this occurs, your
display shows: POWER SAVE MODE, PRESS“START” TO EXIT.
While in this mode, your fax machine automatically switches back to full
operation after you press the Start key, when the telephone rings, when the
telephone handset is lifted, or when a document is loaded. Available
settings are on and off.
20:ECM FUNCTION:
The error correction mode function helps your fax
machine to improve communication in areas where telephone line
conditions are poor. Available settings are on and off.
Note:
When using ECM, the transmitting fax machine
automatically checks the data as it is sent. If the
receiving fax machine cannot verify the
transmission, the transmitting fax machine will
retransmit as necessary. Using ECM also increases
transmission time because the data is checked as it is
transmitted.
Programming 69
English
21:REMOTE DIAGNOSIS:
The remote diagnostics feature allows a
service person to remotely dial and service your fax machine. Available
settings are on and off.
22:PC/FAXSWITCH:
When your fax machine is set to answer in PC
Receive Mode and your optional MFP software is set to receive fax
messages, all incoming calls are transferred directly to your PC. However,
if you are experiencing a problem with your PC, you can tell your fax
machine to receive and print faxes locally by setting this function to on.
Available settings are on and off.
23:ONE TOUCH PARAM:
This function allows you to make changes to
the communications settings for a specific One Touch key, without
changing the normal communication settings used by your fax machine.
For instructions on changing One Touch Parameters settings for a One
Touch key, see One Touch parameters in Dial Directories.
Changing user function settings
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows
1:FUNC. PROGRAMMING.
3. Press the YES key. The display shows FUNCTION NO. [ ].
4. Using the numeric keypad, enter the 2-digit number of the function
you want to change. This display then shows the name of the
selected function.
5. Press the NO key to cycle through the settings for the user function,
then press the YES key to confirm your selection. The name of the
next user function appears in the display.
6. Press the Select Function key to finish.
Dial parameter settings
These functions allow you to control the way your fax machine dials
telephone numbers. Refer to Dial Parameter Settings List to determine
which settings you may need to change, then refer to Changing Your Dial
Parameter Settings to make the change.
70 User’s Guide
Note:
Some settings are not available in some countries. If
you have trouble accessing a dial parameter setting
listed here, contact your dealer for assistance.
Dial parameter settings list
REDIAL TRIES:
This function controls how many times your fax
machine automatically redials a number which is busy or which does not
answer. Available settings are from 0 to 10 tries.
REDIAL INTERVAL:
The function controls how long your fax machine
waits between each automatic redial attempt. Available settings are from
1 to 6 minutes.
DIAL TONE DETECT:
This function allows your fax machine to wait
for and detect a dial tone before proceeding with dialling. Available
settings are on and off.
BUSY TONE DETECT:
This function allows your fax machine to detect
a busy tone when sending a fax. Available settings are on and off.
MF(TONE)/DP(PULSE):
This function controls what method your fax
machine uses for dialling. Two dialling methods are in common use. DP,
or dial pulse dialling, uses monotone pulses to dial a number (like a rotary
telephone). MF, or multi-frequency dialling (touch tone), uses different
tones to dial a number. Available settings are MF and DP.
PULSE DIAL RATE:
If your fax machine is set to pulse dialling, this
function controls how quickly your fax machine sends our dialling pulses
(the dial pulse rate varies in different countries). Available settings are 10
pps, 16 pps and 20 pps.
PULSE MAKE RATIO:
Available settings are 33% and 39%.
PULSE DIAL TYPE:
If your fax machine is set to pulse dialling, this
function controls the type of pulse dialling used (different types of pulse
dialling are used in different countries). Available settings are N, 10-N and
N+1.
MF(TONE) DURATION:
If your fax machine is set to tone dialling, this
function controls the duration of the tones used for dialling (the tone
duration varies in different countries). Available settings are 75 ms, 85 ms,
and 100 ms.
PBX LINE:
Turn this function on if your fax machine is connected to a
PBX. Once this function has been turned on and the dial prefix function
has been programmed, your fax machine will recognize the dial prefix
Programming 71
English
number you use in your PBX to get an outside line. After it dials your dial
prefix number, your fax machine pauses to wait for an outside line before
dialling the rest of the telephone number. Available settings are on and off.
See Connecting to a PBX in Installation for instructions on changing this
setting.
FLASH/EARTH/NORMAL:
If your fax machine is connected to a PBX,
this function tells your fax machine about the type of PBX line your fax
machine if connected to. Available settings are normal (N), flash (F) and
earth (E).
AUTO START:
When this function is turned on, your fax machine will
automatically begin dialling as soon as you have selected a location by
pressing a One Touch key or entering an Auto Dial code. You do not have
to press the Start key. Available settings are on and off.
DIAL PREFIX:
If your fax machine is connected to a PBX, use this
function to tell your fax machine what access number is used to obtain an
outside line from your PBX. You can enter up to 4 digits. See Connecting
to a PBX in Installation for instructions on changing this setting.
IT2 DETECT:
This is another type of dial tone detection (France only).
Available settings are on and off.
Changing dial parameter settings
1. Press the Select Function key.
2. Press the 9/User Program One Touch key. The display shows:
1:FUNC. PROGRAMMING.
3. On the numeric keypad, press 2. The display shows 2:DIAL
PARAMETER.
4. Press the YES key until the display shows the dial parameter you
want to change.
5. Repeatedly press the NO key until the setting you want appears in
the display.
6. Press the YES key to confirm your selection. The name of the next
dial parameter setting will appear in the display.
7. Press the Select Function key to finish.
72 User’s Guide
Service function settings
Service function settings in many cases greatly change the way your fax
machine operates. To change any of these settings, contact your dealer.
Service function settings list
LONG DOC. STX:
Normally, your fax machine will not scan documents
longer than 360 mm. When this function is on, your fax machine will scan
and transmit documents of any length for up to one hour.
MDY/DMY:
This function controls how your fax machine displays and
prints the date (month / day / year or day / month / year).
TIME/DATE PRINT:
This function controls how the time and date are
printed on the fax messages which you transmit. Your fax machine can be
set to not print the time and date, to print it at the top the first page only, or
to print it at the top of every page.
TSI PRINT:
When this function is on, the telephone number of the fax
machine sending you a fax message is printed at the top of each page of
the message.
NO TONER MEM. RX:
When this function is turned on, your fax
machine automatically receives messages in memory when it is low on
toner.
TAD MODE:
This function allows an answering machine to operate on
the same line as your fax machine.
TEL/FAX SW.:
When this function is on, the telephone/fax [T/F]
answering mode is available, which allows your fax machine to
automatically distinguish between incoming voice and fax telephone calls.
MONITOR CONT.:
This function controls the line monitoring sounds
you hear while your fax machine is dialling and all fax communication
sounds. Available settings are on and off.
REAL TIME DIAL:
This function controls how you can dial telephone
numbers on your fax machine. Normally, your fax machine waits for you
to enter an entire telephone number and press Start before dialling. When
this function is set to type 1, you can dial immediately (digit by digit)
whenever you pick up the handset. When this function is set to type 2, you
can dial immediately whenever you pick up the handset or press the Hook
key. Available settings are off, type 1 and type 2.
Programming 73
English
TONE FOR ECHO:
This function compensates for poor overseas line
conditions. Available settings are on and off.
MH ONLY:
This function controls the type of compression method your
fax machine uses during communication. Adjusting may also help in poor
line conditions. Available settings are on and off.
H/MODEM RATE:
This function controls the communications speed
your fax machine’s modem uses at the beginning of a fax communication.
Available settings are 28.8K,14.4K, 9.6K and 4.8K.
74 User’s Guide
Reports 75
English
Reports
Understanding reports
Your fax machine provides a variety of useful reports which help you
understand the current settings, programming and operations of your fax
machine. Refer to the reports listing below to determine which reports you
may want to print, then refer to Printing Reports for instructions on
printing a report.
Activity report
The activity report provides a communication record of your fax machine.
Information provided on this report includes:
• The total amount of time your fax machine spent sending faxes and
the total amount of time spent receiving faxes.
• The date, time and duration (S,R-TIME) of each transmission or
reception.
• The name or telephone number of the fax machine you were
communicating with (DISTANT STATION ID). If you were
sending a fax, the Personal ID or telephone number of the remote
fax machine that received the document will be printed. If the
remote fax machine does not have a Personal ID or telephoned
number programmed, the Location ID or telephone number you
entered will be printed. If you were receiving a fax, the Personal ID
or telephone number of the remote fax machine that sent the
document will be printed. If you were receiving a fax and the
remote fax machine does not have a Personal ID or telephone
number programmed, no data is printed.
• The communication mode used for each transmission or reception.
• The number of pages sent or received.
• The result of each communication.
• Service codes.
76 User’s Guide
Note:
This report does not contain the results of fax
messages which were received without errors and
printed immediately, i.e. only transmissions,
receptions with errors amd memory receptions are
recorded.
Broadcast confirmation report
Use this report to confirm the results of a multiple-location transmission
(or broadcast). Information provided on this report includes:
• The date and time at which the broadcast started.
• The total amount of time used to complete the broadcast.
• For each location, the Location ID or telephone number, the number
of pages sent and the result of the communication.
Note:
If there have been no transmissions to multiple
locations (broadcast) then this report cannot be
printed
Telephone directory
This report provides a complete listing of all of the telephone numbers
programmed for the One Touch keys, Auto Dial codes and groups of your
fax machine. The information includes:
• The Location ID and main fax number (TEL NO) for each One
Touch key and Auto Dial code.
• The alternate number (OR) for each One Touch key.
• The One Touch Parameter settings (PRM. ECHO) and transmission
speed (RATE) for each One Touch key.
• The Location ID and fax number (TEL NO) for each Auto Dial
code.
• A listing of all of the One Touch keys and Auto Dial codes included
in each group.
Reports 77
English
Configuration report
The configuration report provides a list of the current operational settings
of your fax machine that can be set by you. The information includes:
• The current settings of all your fax machine’s user functions (except
for One Touch Parameter settings, which appear in the telephone
directory).
• The Sender ID (ID=), fax number (TEL NO.) and call back number
(CALL BACK NO.) currently programmed into your fax machine.
• The current setting of dial parameters for your fax machine.
Message confirmation report
This report provides information about your last single-location fax
transmission or polling transmission. Information in this report includes:
• The date of the communication.
• The total amount of time your fax machine spent sending or
receiving (S,R-TIME).
• The Personal ID or telephone number of the fax machine you were
sending a fax to (DISTANT STATION ID). If the remote fax
machine does not have a Personal ID or telephone number
programmed, the Location ID or telephone number you entered is
printed.
• The communication mode used.
• The number of pages sent or received.
• The result of the communication.
• Service codes.
• Depending on the settings of your fax machine, a portion of the
page will be printed after the report (see 04:IMAGE IN MCF. in
Programming)
Confidential reception report
This report is automatically printed each time your fax machine receives a
confidential message into a mail box. Information in this report includes:
• The date the message was received.
• The total amount of time your fax machine spent receiving the
message (S,R-TIME).
78 User’s Guide
• The Personal ID or telephone number of the fax machine you were
communicating with (DISTANT STATION ID). If the Personal ID
or telephone number has not been programmed by the sending fax
machine, no DISTANT STATION ID is recorded.
• The number of the mail box into which the message was received.
• The number of pages sent or received.
• The result of the communication.
• Service Codes
Broadcast entry report
Each time you program a multiple-location transmission (or broadcast),
your fax machine will give you the option of printing this report to confirm
your entries. Information in this report includes:
• The Location ID of the One Touch keys and Auto Dial codes you
have selected.
• Telephone numbers you have manually entered using the numeric
keypad.
Power outage report
If the electrical power to your fax machine has been interupted and your
fax machine had delayed transmissions or messages received into
memory, your fax machine automatically prints a power outage report to
alert you that fax messages have been lost.
If your fax machine has a memory expansion board installed and power
has been interrupted for more than one hour, then the power failure may
have interfered with delayed transmissions, messages received into
memory or other communications. In this case, your fax machine
automatically prints a power outage report to alert you.
Printing reports
Printing message confirmation report
After transmission, press the Copy key once (with no documents loaded)
to see a report confirming your transmission on the display of your fax
machine. To print the report, press the Copy key a second time.
Reports 79
English
Printing other reports
1. Press the Select Function key.
2. Press the 6/Report Print One Touch key. The display shows
1:ACTIVITY REPORT.
3. Press the NO key repeatedly until the report you want to print
appears on the display.
4. Press the YES key. The report will begin printing.
5. Press the Select Function key to finish.
Codes used in reports
Result codes
The following codes indicate the results of communications.
Communication codes
The following codes indicate the communication mode used for a
communication.
Code Description
BUSY The other machine’s line was busy or there was no answer.
COMP. A multiple-location transmission was completed.
COVER The fax machine’s cover was opened during the communication.
NO The transmission or reception failed due to a communication error.
OK The communication was completed successfully.
PAPER The communication failed because the receiving machine ran out of paper.
PUNIT This error code indicates a problem with the printing unit. Contact your dealer.
R_JAM A paper jam occurred in your fax machine while it was receiving a fax, and your
fax machine was unable to receive the entire message in memory
S_JAM A document jam occurred in the sending fax machine.
STOP The Stop key was pressed, ending the communication session.
Code Description
B.C. Multiple-location transmission (broadcast).
BOX Reception into a personal mail box.
CALLING A communication initiated by your fax machine.
CALLED A communication initiated by a remote fax machine.
80 User’s Guide
Problem Solving 81
English
Problem Solving
Clearing document jams
When a document jam occurs, your fax machine beeps and an error
message appears in the display. If the jammed document looks like it is
positioned straight in your feeder, press the Stop key to try to feed the
document the rest of the way through the feeder. If this fails, follow the
instructions below.
1. Grasp the control panel. Pull up and toward you until it releases.
Swing the control panel out of the way.
2. Pull out the jammed document.
3. Push the control panel back down until it locks.
82 User’s Guide
Clearing printer paper jams
If your fax machine displays PAPER JAM or NO PAPER when the paper
cassette still contains paper, there may be one or more sheets of paper
jammed in the machine. To clear a paper jam, follow the instructions
below.
Note:
If you are experiencing many paper jams, it may be
due to the type of paper you are using. For best
results, select a paper which has been developed
specifically for photocopying or laser printing. Be
sure to fan the paper before loading it into your
paper tray.
1. Turn the power switch off (the O should be pressed down).
2. Lift the document table and swing it out of the way.
3. Check for paper jammed in the slot where received faxes or copies
exit onto the document stacker. If you see paper jammed in the exit
slot, lift the blue bar out of the way and pull the paper out.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
AU
TO
R
EC
SEAR
C
H
SELECT
FUNCTION
AU
TO
D
IAL
HYPH
EN
R
EDIAL
CO
PY
HO
O
K
V. R
EQ
U
EST
PHO
TO
EX FIN
E
FIN
E
STD
LIG
HT
N
O
R
M
AL
DAR
K
ALAR
M
STO
P
STAR
T
Problem Solving 83
English
4. Push the buttons on the side of the copy stacker until you hear a
click. Lift the copy stacker out of the way.
CAUTION:
Never expose the image drum unit to light for more than 5 minutes. Never
expose the image drum unit to direct sunlight. Always hold the image drum
unit by the ends. Never touch the surface of the green drum inside the image
drum unit.
5. Lift the image drum unit out and set it aside. Keep it out of direct
sunlight and DO NOT touch the green surface of the drum.
6. Carefully pull out any paper you see jammed inside the machine.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
HYP
COPY
H
OOK
V. REQU
EST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
PUSH
PUSH
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
START
84 User’s Guide
7. Pull out the paper cassette. If any of the paper in the paper cassette
is damaged, remove and replace it.
8. Push the paper down until it is under the plastic tabs.
9. Slide the paper cassette all the way back into your fax machine.
10. Place the image drum unit back into your fax machine. To ensure
that the image drum is positioned correctly, press down firmly on
both of the locations on the image drum marked “PUSH”.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELEC
T
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
ART
PUSH
PUSH
Problem Solving 85
English
11. Close the copy stacker and push down on it until you hear a click.
Be sure both slides are latched.
12. Close the document table.
13. Turn the power switch back on (the I should be pressed down).
Replacing toner cartridge
The number of pages you can print with one toner cartridge varies
depending on the type of documents you usually receive or copy. A toner
cartridge will print about 2500 pages/A4 size of standard business
communications at a typical print coverage of 4% (equivalent of CCITT
No. 1 test chart). The first toner cartridge installed in a new image drum
unit will have a decreased yield because the image drum unit itself has to
be filled.
If your fax machine displays TONER LOW or REPLACE TONER
CART., replace the toner cartridge with a new one. However, if the print
density is high enough, you can continue to use the toner cartridge without
replacing it until the print density becomes too low.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
STAR
T
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
86 User’s Guide
If the print density becomes low even before your fax machine displays
TONER LOW or REPLACE TONER CART., gently wipe the lens surface
of the LED array (see Step 8 ). If the print density does not improve,
replace the toner cartridge. When your fax machine’s display shows
CHANGE DRUM, replace the image drum unit.
WARNING
Be careful when handling the toner cartridge. Do not let toner spill on
your clothing or other porous materials. See Safety at the beginning of this
user’s guide.
1. Turn the power switch off.
2. Lift the document table into an upright position.
3. Push in the cover release buttons on the side of the copy stacker
until you hear a click. Lift the copy stacker.
4. Pull the coloured lever on the old toner cartridge all the way toward
you. Carefully pull the old toner cartridge out of the image drum
unit. Dispose of it in the plastic bag you received with your new
toner cartridge.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
Problem Solving 87
English
5. Remove the new toner cartridge from its package and gently shake
it from side to side to distribute the toner. Then carefully peel the
white plastic tape from the bottom of the toner cartridge.
CAUTION:
Be careful not to insert the toner cartridge backwards into the image drum
unit.
6. With the ridged side facing up and the coloured lever on your right,
insert the toner cartridge into the image drum unit. Slide the left end
of the cartridge in first, then lower the right end into place.
7. Once the toner cartridge is in place, push the coloured lever all the
way forward to secure it and release the toner.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
PHOTO
EX FIN
LIGH
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
SEA
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
88 User’s Guide
8. Using the cleaning wipe provided in the package with your new
toner cartridge, gently wipe back and forth across the full length of
the LED array.
9. Close the copy stacker and push down until you hear the copy
stacker click into place. Be sure that the cover latches on both sides.
10. Close the document table.
11. Turn the power switch back on (the I should be pressed down).
CAUTION:
Please abide by the disposal laws of your country when disposing of replaced
toner cartridges.
Replacing image drum unit
If the faxes you receive are light or have vertical streaks in them and you
are not out of toner, or if your fax machine displays a CHANGE DRUM
message, your fax machine needs a new image drum unit. Contact your
dealer to order one.
The life of an image drum depends on a number of factors, including
temperature and humidity, the type of paper you use, and the number of
pages per job. The image drum cartridge should last about 10,000 pages
for continuous printing, up to 8,000 pages at 3 pages per job, and about
4,500 pages at 1 page per job.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
STAR
T
Problem Solving 89
English
CAUTION:
Never expose the image drum unit to light for more than 5 minutes. Never
expose the image drum unit to direct sunlight. Always hold the image drum
unit by the ends. Never touch the surface of the green drum inside the image
drum unit.
1. Turn the power switch off (the O should be pressed down).
2. Lift the document table into an upright position.
3. Push in the cover release buttons on the side of the copy stacker
until you hear a click. Lift the copy stacker.
4. Remove the old image drum unit (with its toner cartridge), wrap it
in the packaging materials from your new image drum unit, and
throw it away.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
SELECT
FUNCTION
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
ST
AR
T
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
HYPHEN
R
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALAR
M
ST
PUSH
PUSH
90 User’s Guide
5. Take the new image drum unit out of its package and insert it into
your fax machine. To ensure that the image drum is positioned
correctly, press down firmly on both of the locations on the image
drum marked “PUSH”.
6. Install a new toner cartridge. Follow Steps 5-10 in Replacing the
Toner Cartridge.
7. With the copy stacker and document table closed, turn the power
switch back on (the I should be pressed down).
8. Wait until the time, date and answering mode appear on the display.
Then press the Select Function key.
9. Press the 7/Counter Display One Touch key. The display shows
DRUM COUNT.
10. Press the YES key to clear the image drum unit counter.
11. Press the Select Function key to finish.
CAUTION:
Please abide by the disposal laws of your country when disposing of replaced
Image Drum Units.
Reading print counters
The print counters of your fax machine count the number of pages your fax
machine has printed or scanned in its lifetime. If you are experiencing a
problem, a service person may ask you to check these counters.
1
ABC
2
DEF
3
GHI
4
JKL
5
MN
6
PRS
7
TUV
8
WXY
9
*
OQZ
0
#
AUTO REC
SEARCH
FU
AUTO DIAL
HYPHEN
REDIAL
COPY
HOOK
V. REQUEST
PHOTO
EX FINE
FINE
STD
LIGHT
NORMAL
DARK
ALARM
STOP
START
Problem Solving 91
English
Note:
If the image drum unit has reached the end of its life,
you will also use this function to reset the drum
counter. Refer to Replacing Image Drum Unit above
for more information.
1. Press the Select Function key.
2. Press the 7/Counter Display One Touch key. The display shows
DRUM COUNT.
3. Press the NO key. The display shows the PRINT COUNT.
4. Press the NO key again. The display shows the SCAN COUNT.
5. Press the Select Function key to finish.
Problem checklist
Your fax machine is a complex machine with many features and functions
which allow it to operate in different ways. Many problems you experience
may be due to improper programming. If you are experiencing a problem,
read through the list of problems and solutions before calling your dealer.
Your telephone does not ring if your fax machine is set tel/fax
answering mode and the incoming call is a voice call.
This is normal. In
the tel/fax answering mode, your fax machine answers the incoming call
and detects if the call is a voice call or a fax call. If the call is a voice call,
your fax machine will ring, but your telephone will remain silent. It is
recommended that you only use tel/fax answering mode if your telephone
is located near the fax machine.
The display is blank.
Check that the power switch is on. Check the power
cord to make sure that it is firmly plugged in. Check your wall outlet to
make sure that it has power.
Nothing happens when you press the control panel keys.
Turn the fax
machine off, wait 10 seconds, then turn it on again.
The display tells you to replace paper even though there is paper in the
paper cassette.
Take the paper cassette out and make sure that the paper
is firmly stacked in the tray. Push the paper firmly under the plastic tabs
on the edge of the tray. Check for a paper jam in the fax machine.
Your documents jam.
Check the document for wrinkles, tears or other
damage. Make sure there are no staples or paper clips and that the paper is
clean and dry. Make sure the document is not wider than your fax machine
92 User’s Guide
can load. Try making a copy of the document on a photocopier and faxing
the copy.
Your fax machine will not dial.
Check the power cable and wall outlet.
Make sure that your telephone line (not your external telephone or
handset) is connected to the LINE outlet on the back of your fax machine.
If you have an external telephone connected, lift the handset and check for
a dial tone. If you do not have an external telephone connected, press the
Hokk/V. Request key and check for a dial tone. If you do not hear one,
there may be a problem with your telephone line. If you do hear a dial tone,
your fax machine may be using the wrong dialling method (pulse or tone)
for your area. If you hear changing tones instead of dialling pulses and you
know that your area uses pulse dialling, refer to the MF(TONE)/
DP(PULSE) dial parameter setting in Programming. If your fax machine
is connected to a PBX, make sure you have programmed to work with a
PBX (see Connecting to a PBX in Installation).
The display shows a communication error.
This alarm indicates any of
a number of problems. You may be trying to communicate with an
incompatible fax machine (your machine can only communicate with
ITU-T Group 3 fax machines). The remote machine may not be able to
perform the function that you want, such as polling or confidential
messages. The remote machine may also be out of paper or experiencing
a paper jam. Bad telephone line conditions can also cause communication
errors. Try sending the fax again and check to make sure you are dialling
the correct telephone number. If you have to dial an access digit to get an
outside line, or if you are dialling internationally, you may need to enter a
pause (using the Pause One Touch key) after the access digit or
international dialling code to tell your machine to wait for a dial tone. If
you have frequent problems communicating with a particular remote fax
machine, try programming the number into one of your One Touch keys
and then changing the One Touch Parameters for that One Touch key (see
Dial Directories). Lastly, either your fax machine or the remote fax
machine may need servicing. Try sending a fax to another location to
check your machine.
You sent a fax but the image the remote fax machine received was
very poor.
If your document had a lot of small type, complex illustrations,
photos, or was very light or very dark, try changing your Transmit
Resolution and Type of Original settings (see Loading Documents in Basic
Operations). Copy the document on your fax machine to see how it will
transmit. The problem may be caused by telephone line interference. Try
sending the document again later.
Problem Solving 93
English
You keep getting reports you do not want.
Check your user function
settings and turn off the reports you do not want. See Programming.
You sent a fax but it was received completely blank.
Make sure that you
have correctly loaded your document face down.
The image received on your fax machine was very poor.
Contact the
person sending you the fax and ask them to change their Transmit
Resolution and Type of Original settings. Ask the person to make a copy
of the document on their fax machine to ensure that it is working properly.
Then ask them to send the fax again. If you still have a problem, try making
a copy of a document on your machine to make sure it is working properly.
You tried dialling with a One Touch key or an Auto Dial code but
nothing happened.
Make sure that something is programmed into the One
Touch key or Auto Dial code you are using. Check the fax number to make
sure it was entered correctly (see Dial Directories). When you are dialling
with an Auto Dial code, be sure to press the Auto Dial key before you enter
the code. If your fax machine has the Auto Start feature turned off, you will
have to press the Start key before dialling will begin (see Programming).
Your fax machine does not answer the phone or receive faxes.
First
check to see that the power cable is connected to the power outlet and the
telephone line is connected to LINE. Also check the reception mode you
are using. Your fax machine will not automatically receive faxes in manual
answering mode [TEL]. See Setting the Answering Mode in Installation.
Your received documents are light or have vertical streaks on them
and you are not out of toner.
Gently wipe the lens surface of the LED
array on your fax machine and then see if the machine works properly
(refer to Replacing the Toner Cartridge). If your fax machine still does not
work properly, remove the image drum unit (refer to Replacing the Image
Drum Unit), tap the toner cartridge, and slowly swing it 20-30 degrees
vertically several times. Be careful not to let the toner leak from the
cartridge. If this does not work, you may need to replace your image drum
unit. Contact your dealer to get a replacement.
You set your fax machine for delayed transmission but it did not send.
Check the display to make sure that you have set the clock on your fax
machine to the correct time. See Setting Time & Date in Installation.
Your fax machine disconnected before you could answer a voice
request.
You must answer a voice request while the warbling tone is being
emitted. When you hear the warbling tone, press the Hook/V. Request Key
after picking up your handset.
Someone tried to send you a confidential fax but nothing happened.
You must set up a mail box before anyone can send you a confidential fax.
94 User’s Guide
See Receiving Confidential Faxes in Advanced Operations. Make sure the
person sending you the fax knows the correct mail box number.
Your fax machine will not poll a remote fax machine.
Call the person
at the remote fax machine and make sure that they have loaded documents
and set their fax machine in polling transmission mode. Check also if their
fax machine uses either standard polling transmission or ITU polling
transmission.
Your fax machine is connected to a PBX and you can not dial out.
You
must enter your access digit before the telephone number for each number
that you dial or program into your machine. Also, your fax machine must
be programmed for PBX operation before it will work. See Connecting to
a PBX in Installation.
You want to answer an external telephone but your fax machine
always answers first.
If you are using an external telephone, change the
user function setting for ring response on your fax machine. See
Programming.
Your received faxes sometimes look distorted.
If the document received
is wider or longer than the paper you have loaded into your paper tray, your
fax machine automatically reduces either the width or the length of the
document to fit on your paper. This type of problem could also be
communication related.
You are constantly receiving unsolicited advertising on your fax
machine.
Try using the closed network function. See Receiving Faxes in
Basic Operations.
Your fax machine does not immediately switch to TEL mode when
you make or receive a voice call.
Try pressing the Stop key. Your fax
machine will return to standby mode so that you can converse. This
condition may happen infrequently due to telephone line conditions, or the
type of external telephone used. If this problem happens often, consult
your service representative.
Specifications 95
English
Specifications
Category Specifications
Type/compatibility Desktop ITU-T G3 transceiver
Applicable network PSTN, PBX, leased and private lines
Transmission Speed 28800/26400/24000/21600/19200/16800/14400/9600/
7200/4800/2400 Automatic fall back
Communications Half duplex
Coding scheme MH/MR/MMR with ITU-T ECM
Horizontal resolution 8 pel/mm
Vertical resolution 3.85 line/mm (standard)
7.7 line/mm (fine)
15.4 line/mm (ex. fine)
Halftone transmission 64 shades of gray
Document size A4, A5, letter or legal size
Recording paper Plain paper, A4, letter or legal size
Effective scan width 215 mm
Weight 12 kg approx. (excluding paper)
Display 2 rows of 20 characters, LCD panel
Dimensions Approx. 330 mm (W) x 420 mm (D) x 245 mm (H)
(excluding document tray and document stacker)
Power 220/240 ± 10% VAC, 50/60 Hz ±2%
Operating conditions Relative humidity 20%-80%(non condensing)
Temperature 10°C to 32°C
Document feed
30 pages maximum (80g/m
2
A4 size)
Model number for approvals
organisations
Model FX-175VP
96 User’s Guide
… 25 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Oki of 5400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Oki of 5400 in de taal/talen: Engels als bijlage per email.

De handleiding is 2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info