47665
38
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
1.1.1.
Océ PP16C
Quick Reference Guide
Education Services
Océ
Reference Guide
English version
Notice
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY
IMPROPER INSTALLATION OF THE PRODUCT.
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE
PRINTER’S NATIVE MODE OR ONE OF ITS EMULATION
MODES.
The information in this manual is subject to change without notifi-
cation. Additional pages may be inserted in future editions. The
user is asked to excuse any technical inaccuracies or typographi-
cal errors in the present edition.
No responsibility is assumed if accidents occur while the user is
following the instructions in this manual. No responsibility is
assumed for defects in the printer’s firmware (contents of its read-
only memory).
This manual, any copyrightable subject matter sold or provided
with or in connection with the sale of the page printer, are pro-
tected by copyright. All rights are reserved. Copying or other repro-
duction of all or part of this manual, any copyrightable subject
matter without the prior written consent of Kyocera Mita Corpora-
tion is prohibited. Any copies made of all or part of this manual,
any copyrightable subject must contain the same copyright notice
as the material from which the copying is done.
©2003 KYOCERA MITA CORPORATION. All rights reserved.
The names of actual companies and products mentioned herein
may be the trademarks of their respective owners.
FSC5016N_QG.fm 0 ページ 2003年3月24日 月曜日 午後1時47分
FS-C5016N
Quick Reference
Guide
FSC5016N_QG.fm 1 ページ 2003年3月24日 月曜日 午後1時47分
2
Contents
Guide to the information about the printer .................................3
Understanding the Error Messages ...........................................4
Loading Paper .........................................................................14
Clearing Paper Jams ...............................................................22
Jam at the Paper Cassette .........................................23
Jam at the Paper Transfer Unit ...................................23
Jam at the Rear Cover ................................................25
Jam at the MP Tray .....................................................26
Toner Container Replacement ................................................27
Replacing the Toner Container ...................................28
Replacing the Waste Toner Box .................................32
Cleaning the Printer .................................................................35
Cleaning the Main Charger Unit ..................................35
Cleaning the Paper Transfer Unit ...............................40
FSC5016N_QG.fm 2 ページ 2003年3月24日 月曜日 午後1時47分
3
Guide to the information about the printer
The following documentation and CD-ROM are sup-
plied:
Installation Guide This guide provides information on installing
the printer before starting to use.
Quick Reference
Guide (This booklet)
This guide provides common information
about the printer such as loading paper,
understanding messages, etc.
Operation Guide This guide is supplied as an online manual
(PDF) in the CD-ROM. This guide fully details
the information on the printer features, hard-
ware, troubleshooting, printer driver handling,
etc.
KX Printer Drivers
Operation Guide
This guide is supplied as an online manual
(PDF) in the CD-ROM. This guide explains
how to install and configure the printer driver.
Software and Docu-
ment CD-ROMs
These CDs include the printer software for
Kyocera Mita printers such as printer drivers,
network printer monitors, and various soft-
ware utilities. Also, these CDs include the
Operation Guides and other documents.
Web site The latest versions of printer drivers and utili-
ties are available for downloading at:
http://www.kyoceramita.com/download/
FSC5016N_QG.fm 3 ページ 2003年3月24日 月曜日 午後1時47分
4
Understanding the Error Messages
These messages appear on the printer’s message dis-
play when the printer needs the operator’s attention.
For more details, refer to chapter 4 of the Operation
Guide.
Message Corrective Action
Add paper MPTray
The paper has run out in the paper source
displayed. Supply paper according to the
paper source (paper cassettes, MP tray,
optional paper feeders, or optional enve-
lope feeder).
This message is displayed alternately with
messages indicating the printer status,
such as, Ready, Please wait, Pro-
cessing, Waiting, and Form Feed
Time Out. If the number of copies to
print is 2 or more, only the Add paper
message is displayed.
Call service
F###:
F### represents a controller error (#=0, 1,
2, ...). Call a service. The printer does not
operate when this message is displayed.
Call service
####:0123456
#### represents a mechanical error (#=0,
1, 2, ...). Call a service. The printer does
not operate when this message is dis-
played. The total number of pages printed
is also indicated, e.g. 0123456.
Call service
Person F0
This message means an error in data
communications between the printer con-
troller and the operator panel. Call a ser-
vice.
Cassette #
not loaded
The corresponding paper cassette is not
installed. Install the cassette. The cassette
number can be 1 (topmost) to 4 (bottom).
FSC5016N_QG.fm 4 ページ 2003年3月24日 月曜日 午後1時47分
5
Check waste
toner box
This message warns following two cases.
Install the new waste toner box.
The waste toner box is not installed.
The waste toner box is almost full.
Clean printer
Press GO
Please clean the inside of the printer. See
Cleaning the Printer on page 35.
This message will be displayed when
replacing the toner container after the
message Replace toner C, M, Y, K is
displayed. After cleaning the inside of the
printer, press the GO key and the printer
will be ready for printing.
If Auto Continue is set to On, printing will
be automatically resumed after a preset
period of time. For details on Auto Con-
tinue, refer to chapter 3 of the Operation
Guide.
Close duplexer
rear unit
The rear unit of the optional duplexer is
open. Close the duplexer rear unit.
Close duplexer
top cover
The top cover of the optional duplexer is
open. Close the duplexer top cover.
Close paper
transfer unit
The paper transfer unit is open. Close the
paper transfer unit.
Close
left cover
The left cover of the printer is open. Close
the printer left cover.
Close
rear cover
The rear cover of the printer is open. Close
the printer rear cover.
Message Corrective Action
FSC5016N_QG.fm 5 ページ 2003年3月24日 月曜日 午後1時47分
6
Close
top cover
The top cover of the printer is open. Close
the printer top cover.
Duplex disabled
Press GO
You attempted to print with a paper size
and paper type that cannot be used for
duplex printing. Press the GO key to print
onto one-side of the paper only.
Face-down tray
paper full
The face-down tray has become full
(approx. 250 pages). You must remove all
printed pages from the face-down tray.
When the printer detects that the face-
down tray is empty again, the printer will
continues printing into the face-down tray.
File not found
Press GO
You have attempted to print a job that is
not contained in the specified virtual mail-
box, or the specified virtual mailbox is not
found.
If Auto Continue is set to On, printing will
be automatically resumed after a preset
period of time. For details on Auto Con-
tinue, refer to chapter 3 of the Operation
Guide.
Format error
Hard disk
The hard disk installed in the printer is not
formatted, and therefore cannot be read or
written. To format the hard disk, follow the
procedure in the Installation Guide of the
hard disk.
Format error
Memory card
The memory card inserted in the printer is
not formatted, and therefore cannot be
read or written. To format a memory card,
follow the procedure in chapter 3 of the
Operation Guide.
Message Corrective Action
FSC5016N_QG.fm 6 ページ 2003年3月24日 月曜日 午後1時47分
7
Hard disk err
##
Press GO
A hard disk error has occurred. Look at the
error code given in place of ## and refer to
chapter 4 of the Operation Guide. To ignore
the hard disk error, press the GO key.
I/F occupied
This message is displayed when you
attempt to use the printer’s operator panel
to change the environmental settings on
the interface from which data are presently
being received.
ID error
The user ID entered for a private job, or a
stored job is not correct. Check the user ID
that you specified on the printer driver.
Insert the same
memory card
You have inserted the wrong memory card
when the Insert again message was
displayed. Remove the wrong memory
card from the printer’s memory card slot
and insert the correct memory card. The
printer again reads it from the beginning of
the data.
Install MK
Replace Maintenance Kit which is dis-
played on the message display. Replace-
ment of the maintenance kit is necessary
at every 200,000 images of printing and
requires professional servicing. Contact
your Kyocera Mita dealer.
Message Corrective Action
FSC5016N_QG.fm 7 ページ 2003年3月24日 月曜日 午後1時47分
8
KPDL error ##
Press GO
Current print processing cannot continue
because of occurrence of KPDL error
which is categorized by ##. To print out an
error report, display > Print KPDL
err(s) from the menu system, and select
On. Press the GO key to resume printing.
You can abandon printing by the CANCEL
key.
If Auto Continue is set to On, printing will
be automatically resumed after a preset
period of time. For details on Auto Con-
tinue, refer to chapter 3 of the Operation
Guide.
Load Cassette #
(
A4
)
/
(
PLAIN
)
The paper cassette matching the paper
size and paper type of the print job is
empty. Load paper into the paper cassette
indicated by #. Press the GO key to
resume printing.
If you want to print from a different paper
source, press the V or U key to display
Use alternative and you can change
the source for paper feeding. After select-
ing a paper source and pressing the
MENU key, Paper Handling >
appears. By pressing the U key, the paper
type settings menu appears. After setting
the correct paper type, press the ENTER
key and printing starts. For details, see
chapter 3 of the Operation Guide.
Message Corrective Action
FSC5016N_QG.fm 8 ページ 2003年3月24日 月曜日 午後1時47分
9
Load EF
(
A5
)
/
(
PLAIN
)
There is no paper cassette installed in the
printer that matches the paper size and
paper type of the print job. Set paper in the
envelope feeder. Press the GO key to
resume printing. (Note that feeding the
paper having a paper size which does not
match the current paper size from the
envelope feeder can cause paper jam.)
If you want to print from a different paper
source, press the V or U key to display
Use alternative and you can change
the source for paper feeding. After select-
ing a paper source and pressing the
MENU key, Paper Handling >
appears. By pressing the U key, the paper
type settings menu appears. After setting
the correct paper type, press the ENTER
key and printing starts. For details, see
chapter 3 of the Operation Guide.
Message Corrective Action
FSC5016N_QG.fm 9 ページ 2003年3月24日 月曜日 午後1時47分
10
Load MP Tray
(
A4
)
/
(
PLAIN
)
There is no paper cassette installed in the
printer that matches the paper size and
paper type of the print job. Set paper in the
MP tray. Press the GO key to resume
printing. (Note that feeding the paper hav-
ing a paper size which does not match the
current paper size from the MP tray can
cause paper jam.)
If you want to print from a different paper
source, press the V or U key to display
Use alternative and you can change
the source for paper feeding. After select-
ing a paper source and pressing the
MENU key, Paper Handling >
appears. By pressing the U key, the paper
type settings menu appears. After setting
the correct paper type, press the ENTER
key and printing starts. For details, see
chapter 3 of the Operation Guide.
Memory card err
Insert again
The memory card is accidentally removed
from the printer’s memory card slot during
reading. If you continue reading the mem-
ory card, insert the same memory card
into the slot again. The printer again reads
it from the beginning of the data.
Also see Insert the same memory
card.
Message Corrective Action
FSC5016N_QG.fm 10 ページ 2003年3月24日 月曜日 午後1時47分
36
There are 4 main charger units, one for each toner con-
tainer. When performing the cleaning procedure, be
sure to clean the main charger unit that corresponds to
the toner container that was replaced. The following
example explains the procedure to clean the main
charger unit for the black toner container.
Open the left
cover.
Main Charger Units
MC
YK
Left Cover
1
FSC5016N_QG.fm 36 ページ 2003年3月24日 月曜日 午後1時47分
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Oce PP16C Quick Reference Guide bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Oce PP16C Quick Reference Guide in de taal/talen: Engels als bijlage per email.

De handleiding is 1,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info