18
� Caution! Special care is required when making
double mitre cuts.
� Do not overload your tool!
� Wear safety goggles.
� Wear a breathing mask on dusty jobs.
� Examine the power cable / extension cable for
damage.
Wear goggles
Wear ear-muffs
Wear a breathing mask
Noise emission values
� The saw’s noise is measured in accordance with
DIN EN ISO 3744; 11/95, E DIN EN 31201; 6/93,
ISO 7960 Annex A; 2/95. The machine may
exceed 85 dB(A) at the workplace. In this case,
noise protection measures need to be introduced
for the user (ear-muffs).
Cutting Idling
Sound pressure level LPA 92,4 dB(A) 93,3 dB(A)
Sound power level LWA 105,4 dB(A) 106,3 dB(A)
„The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.“
5. Technical data
Asynchronous motor 230 V 50 Hz
Power rating 1200 W
Operating mode S1
Idle speed n0 4600 rpm
Carbide saw blade ø 210 x ø 30 x 2.5 mm
Number of teeth 24
Connector for dust extractor ø 35 mm
Standing area 400 x 285
As bench-type circular saw:
Saw table 360 x 250 mm
Cutting height 0 - 33 mm
Parallel stop swinging range -30° to +30°
As mitre box saw:
Tilting range -45° / 0° / +45°
Mitre cuts 0° to 45° to the left
Saw bed support 390 x 140 mm
Sawing width at 90° 120 x 55 mm
Sawing width at 45° 65 x 55 mm
Sawing width at 2 x 45°
(double mitre cuts) 40 x 23 mm
6. Before putting the machine into
operation (Abb. 1-3)
6.1 General information
� The machine has to be set up where it can stand
firmly, e.g. bolt it to a work bench, a universal
base or similar.
� All the covers and safety devices have to be
properly fitted before the machine is switched on.
� It must be possible for the saw blade to run
freely.
� When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
� Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine’s moving parts run smoothly.
� Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
6.2 Converting the combination saw
The saw has two working positions:
A: Bench-type circular saw (Fig. 1)
B: Cross-cut and mitre box saw (Fig. 2)
GB
Anleitung KGST 210/1 19.09.2002 18:49 Uhr Seite 18
Voltage 220-240V~50Hz
Power rating 1500 W
Operating mode S1.1200WS6.25%1500W
No load speed 5000 min
-1
As bench-type circular saw:
Saw table 384x270mm
Cutting height 0 ÷ 33 mm
Parallel stop swinging range -30ºa+30º
As mitre box saw:
Tilting range -45º/0º/+45º
Mitre cuts 0ºto45ºtotheleft
Saw bed support 390x140mm
Max.crosscutat90° 55x115mm
Max.mitrecutat45° 52x77mm
Max.bevelcutat45° 40x110mm
Max.compoundcut45°x45° 35x95mm
Weight 10 kg
Cutting Idling
SoundpressurelevelLPA 98,2dB(A) 93,3dB(A)
SoundpowerlevelLWA 111,2dB(A) 106,3dB(A)
Accelerationvalue=1,814m/s
2
