618122
6
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
6
Rear Panel
1. Master Output (RCA): Use standard RCA
cables to connect this output to speakers or an
amplifier system.
2. USB: Sends USB MIDI data to control various
software parameters.
Performance Pad Modes
The upper row of pads has different functions depending on their mode: Manual Loop Mode,
Auto Loop Mode, and Sample Mode.
To select a mode, hold down the Pad Mode button and
press one of the upper pads.
An LED under the pad section indicates the currently selected
mode.
Manual Loop Mode: Hold Pad Mode and press the pad marked Manual Loop (silkscreened
above the pad) to assign the lower 4 pads to the functions listed below:
Loop In Sets the beginning of a loop. After a Loop Out point is set, when this button is
pressed again, it will allow for fine adjustment of the Loop In point.
Loop Out – Sets the end point for the loop. When this button has been pressed after a
Loop Out point has been set, it will allow for fine adjustment of the Loop Out point.
On/Off – When this is pressed inside a loop, this will turn the loop off. When pressed
outside a loop, this will activate the loop and start playback from its Loop In point. If a loop
has not been set, this button will have no effect.
Loop x1/2 – Cuts the currently playing loop in half. Press Shift + Loop x1/2 to double the
length the currently playing loop.
Auto Loop Mode: Hold Pad Mode and press the pad marked Autoloop to assign the lower 4
pads to the functions listed below:
Auto 1 Sets and starts playback of a 1-beat autoloop.
Auto 2 – Sets and starts playback of a 2-beat autoloop.
Auto 4 – Sets and starts playback of a 4-beat autoloop.
Auto 8 – Sets and starts playback of an 8-beat autoloop.
Sample Mode: Hold Pad Mode and press the pad marked Sampler to assign the lower 4
pads to the functions listed below:
Sample 1 – Plays the sample assigned to Sample Pad 1.
Sample 2 – Plays the sample assigned to Sample Pad 2.
Sample 3 – Plays the sample assigned to Sample Pad 3.
Sample 4 – Plays the sample assigned to Sample Pad 4.
Beatmixing with MIXTRACK PRO 3 and Serato DJ intro
Below is an example of how to mix tracks using MIXTRACK PRO 3 and Serato DJ Intro:
1. Load tracks onto the decks of Serato DJ Intro by using the Load 1 and Load 2 buttons
on MIXTRACK PRO 3.
2. Move the crossfader all the way to the left on MIXTRACK PRO 3.
3. Turn the Cue Mix knob all the way to the right to ‘PGM’.
4. Play the track that is loaded on Deck 1.
5. Play the track that is loaded on Deck 2 and match it’s BPM to Deck 1’s track. To match
the BPM, press Deck 2’s Sync button on MIXTRACK PRO 3.
6. Once the BPM is matched, move the crossfader on MIXTRACK PRO 3 to fade between
Deck 1 to Deck 2.
1
2
1
2
3
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Numark Mixtrack Pro 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Numark Mixtrack Pro 3 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info