618155
5
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
5
REAR PANEL FEATURES
1. POWER CONNECTOR Connect
the supplied power cable here.
2. POWER SWITCH Turns the
machine on and off. The unit should
always be shut down with this
switch first before any external
power is removed.
3. LINE | PHONO INPUTS (RCA) –
Connect audio sources to these inputs. These inputs can accept both line and phono-level signals.
Note: Plug mono audio sources into both left and right inputs using a “Y” cable connector.
4. LINE | PHONO SWITCH – Flip this switch to the appropriate position, depending on the device connected to
the LINE | PHONO INPUTS. If using phono-level turntables, set this switch to "PHONO" to provide the
additional amplification needed for phono-level signals. If using a line-level device, such as a CD player or
sampler, set this switch to "LINE."
5. GROUNDING TERMINAL – If using phono-level turntables with a grounding wire, connect the grounding wire
to these terminals. If you experience a low "hum" or "buzz", this could mean that your turntables are not
grounded.
Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be
connected to the grounding terminal.
6. AUX INPUT (RCA) – Connect an additional line-level audio source to this input. To route the AUX signal to the
mix, you will need to flip the AUX channel's INPUT SELECTOR (located on the top panel) to "AUX."
7. MIC 1 INPUT – Connect a microphone to this input with an XLR or
1/4" cable.
8. MIC 2 INPUT – Connect a 1/4” microphone to this input if you would
like to use an additional microphone on the Aux channel. To route
the MIC2 signal to the mix, flip the AUX channel's INPUT
SELECTOR (located on the top panel) to "MIC2."
9. MASTER OUTPUT (XLR) – Connect this low-impedance XLR output to a PA system or powered monitors.
Control the level of this output with the MASTER fader on the top panel.
10. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier system.
Control the level of this output by using the MASTER knob on the top panel.
11. ZONE OUTPUT (RCA) – Connect this output to an external monitoring device, such as a PA system, powered
monitors, or a home stereo. Control the level of this output with the ZONE knob on the top panel.
LCD FEATURES
1. PLAY / PAUSE – Illuminates when the unit is playing
or paused.
2. CUE – Flashes when a cue point is being set. This is
continuously lit when the unit is paused at a cue point.
3. FOLDER NUMBER – Shows the number of the
current folder.
4. TRACK NUMBER – Shows the current track number.
5. MINUTES – Shows the minutes elapsed or remaining
depending on the TIME MODE setting.
6. SECONDS – Shows the seconds elapsed or remaining depending on the TIME MODE setting.
7. FRAMES – The CD player breaks down a second into 75 frames for accurate cueing. This shows the frames
elapsed or remaining depending on the TIME MODE setting.
8. TIME BAR – Shows either time remaining or elapsed depending on the setting of the TIME button.
9. TIME MODE – Indicates whether the time shown on the LCD is the elapsed time for the track, remaining time
for the track, or total remaining time for the entire CD.
Note: When playing MP3 files, the total remaining time of the CD cannot be shown.
10. BPM – The tempo, which is indicated in BPM (beats per minute). When the automatic beat-counter is on, this
indicator will read "AUTOBPM."
11. PITCH – Shows the percentage change in pitch. When the lock icon is lit, the KEY LOCK button is engaged.
12. LOOP – Indicates when a loop is programmed. When the indicator is flashing, a loop is currently playing. When
"IN / OUT" is shown, a loop is programmed but not currently playing.
13. SINGLE – Shows when the unit is set to play just one track at a time (Single Play Mode). When this is not lit,
the CD will play continuously through all tracks (Continuous Play Mode). This function is controlled by the TIME
button.
Note: When in Single Play Mode, "AUTOCUE" will also be shown. When cueing up a new track, playback will
start when the actual audio of the track starts, eliminating the silence at the beginning of the track.
14. CD / MP3 – Shows when the unit is playing an audio CD or an MP3 CD.
15. MATRIX DISPLAY – Displays folder names and MP3 tag information. If reading a disc with no encoding, the
display will read “NO TEXT”. For CBR-recorded MP3 tracks, the bitrate will be shown. For VBR-recorded MP3
tracks, the display will only show "VBR".
Note: When connecting microphones,
make sure the mic channel's gain knob
is at the lowest setting.
2
1
910
11
5
4
6
8
7
3
3
4
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Numark CDMix Bluetooth bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Numark CDMix Bluetooth in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info