803238
13
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
51
data (see "9. Technical data" on
page 74).
This automatically switches the baby unit
on.
Note: You can also wall mount the baby unit
in a suitable position with the enclosed
screws. Make sure you position the screws
45 mm apart for this.
4.3 Connecting baby unit and
parent unit
Normally, a connection is automatically
established between the two units when
they are switched on:
1. Make sure that the two units are always
within range.
2. To switch the baby unit 1 on, press the
On/Off button 10. To do this, press and
hold the On/Off button until the power
LED 8 lights up.
3. To switch the parent unit 17 on, press the
On/Off button 32 and keep it depressed
until the LED 21 lights up green.
You will hear a beep, the "Hello" screen
will appear, and the parent unit will begin
searching for the connection signal of the
baby unit.
While the connection is being set up, the
connection indicator 20 will light up red.The
screen will remain white and show no video
picture.
The corresponding blue symbol will
appear on the screen of the parent
unit.
As soon as the connection has been
established, the connection indicator 20
on the parent unit 17 and the VOX LED 7
on the baby unit 1 will light up green. The
connection symbol on the screen
disappears, and video transmission
starts.
If the connection setup is not successful
after 30 seconds the parent unit 17 will emit
a beep at regular intervals and the
connection indicator 20 will light up red.
The corresponding red symbol will
appear on the screen of the parent
unit to indicate that the connection
could not be set up.
4. First, check to be sure your baby is still
comfortable.
5. Then move the parent unit to a different
location within the range of the
connection signal so that a connection
can be set up successfully.
The parent unit and the baby unit will
automatically make repeated attempts to
connect until successful.
Note: If the connection indicator 20 begins
to flash green, this means that there is a
connection between the parent unit and the
baby unit, but your baby is currently asleep
and therefore the device has automatically
activated Eco-Mode to reduce the high-
frequency radio waves in baby’s room and
save energy.
Attention! While Eco-Mode is
active, video and sound
transmission is paused. The
screen will go white and the
corresponding symbol in the status bar will
show that Eco-Mode is active. The
connection between the two units remains
established, even while baby is sleeping.
4.4 Power supply
Baby unit
The power supply for the baby unit 1 works
only via the mains adapter. LED 8 lights up
green while the baby unit is on.
Parent unit
The parent unit 17 can be operated on
battery power with no mains connection for
up to 8 hours, or via the mains adapter, with
or without the battery inserted.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nuk Eco Control Video Display 550VD - 10749102 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nuk Eco Control Video Display 550VD - 10749102 in de taal/talen: Engels als bijlage per email.

De handleiding is 0.54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info