709180
12
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
Unit Switch To save the battery on account of the increased The room in which the battery is located must be
The power converter can be switched on via the power dissipation on standby (approx. 1.8 W). well ventilated in accordance with the regulations.
unit switch to the left of the shockproof electric Do not mount the unit directly over heat sources
socket. If no AC consumers are being run off the Installation nor on easily ignitable materials. There must be a
unit, then the power converter is best switched off The SHS200 solar station must be installed near clear space of >100 mm above and below the unit.
the battery in accordance with its protection class.
Connection Schematic circuit diagram
The wiring and fuse protection of the system must conductor on the output side is not keep voltage drops on the line as low as
be carried out in accordance with the regulations permitted and will destroy the unit! possible. If the consumer connections are
on line protection or in accordance with the 2. Connect the battery to the designated screw incorrectly poled, these can still be destroyed
regulations applicable at the time. Before starting terminals -B +B, taking care to pole correctly to despite the fuse protection.
any wiring work, check for correct polarity and that avoid short circuits. In order to keep the voltage
the voltage of the individual system components, drop low and also the heating of the cable
i.e. of the solar station, solar modules, lead-acid connected with it, a flexible cable cross-section
battery, consumers, complies with that specified. If of 4.0 mm² is recommended. A corresponding
in doubt, consult your specialist dealer! When fuse should always be sited directly at the
installing the unit, it is important to observe the battery's plus pole in accordance with the
sequence described: regulations on line protection. The cables
connecting the battery to the station should not
1. Check to see whether the connected battery exceed a length of 3 m. The green LED on the
already has an earth connection. In this case, unit should light up. If not, check the fuse links
the minus pole must be earthed because the and make sure that voltage is being applied to
solar station is earthed internally. If not, connect the connection lead.
the unit's earth connection to your home's earth 3. If the station is so far working correctly, connect
connection. If you do not have an earth the solar module to the screw terminals -M +M,
connection, an earth connection must be taking care to pole correctly.
created in accordance with the regulations (e.g. 4. Connect the DC consumer to the screw
a ground rod). Under no circumstances is it terminals -L +L, taking care to pole correctly.
permitted to operate the unit unearthed Use cable of at least 1.5 mm² or in accordance
because operation of class 1 equipment in with the line protection. If the consumers are a
the presence of an error/failure can prove distance away from the solar station, you should
life-threatening. Earthing the neutral select a larger cable cross-section in order to
Wiring
- Caution: Take care to pole correctly! Follow the safety instructions!
GB
Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Novoferm APS 230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Novoferm APS 230 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Novoferm APS 230

Novoferm APS 230 Aanvulling / aanpassing - Alle talen - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info