707331
31
Verklein
Vergroot
Pagina terug
1/37
Pagina verder
31
ADDItIonAL oPtIonS foR EnCoDERS onLy
REL1 (Relative 1): A message with value 65 is sent out for every clockwise step (increment) and a message with value
63 is sent out for every anti-clockwise step (decrement). With this option the encoder functions as a true endless control
rather than emulates an analogue pot as with the 0-127 and -64/+63 settings.
REL2 (Relative 2): This is similar to the ‘REL1’ setting however it includes encoder acceleration. A message with value
64+n is sent out for every clockwise step (increment) and a message with value 64-n is sent out for every anti-clockwise
step (decrement). The value n depends on how fast you rotate the encoder. It will be 1 when you rotate it slowly and
get larger the faster you rotate it, meaning that you can scale the full range of a parameter with a small quick turn of
an encoder.
0-16K (14-bit mode): MIDI data values are transmitted as a 7-bit binary number, allowing a maximum value range of
0-127. The MIDI Specification allows for two MIDI control messages to be sent together where the data values form an
MSB (most significant byte) and LSB (least significant byte) pair, making a 14-bit binary number and allowing a maximum
value range of 0-16383. This is useful where fine control over a parameter is required, however the parameter you are
controlling must be able to receive 14-bit MIDI values. If you want to send 14-bit values for fine control over a parameter
then set DispType to ‘0-16K’. For CC controls, the MIDI Specification only allows for CC numbers 0 to 31 to be used in this
way. Two CC messages are sent when the value of a parameter is changed – the first with the MSB value and the second
with the LSB value. To enable the receiving device to distinguish between which CC message has the MSB value and which
has the LSB value, the LSB value message is sent using a different CC number, calculated by adding 32 to the original CC
number. Consequently CC numbers 32 to 63 are used for sending the LSB value in 0-16K (14-bit) mode. As an example, if
a CC encoder has DispType set to ‘0-16K’ and CC Num set to 0 then, for each encoder step, two messages will be sent –
a CC0 message with the MSB value and a CC32 message with the LSB value. The important point to note is that if
an encoder has Control set to ‘CC’ and DispType set to ‘0-16K’ then CC Num should only be set from 0 through 31
and not higher.
AP OT: This is a variation of ‘REL2’ and is the same system that is used by some other existing popular control surfaces.
A message with value 0+n is sent out for every clockwise step (increment) and a message with value 64+n is sent out for
every anti-clockwise step (decrement). The value n will equal 1 when you rotate the encoder slowly and increases as you
rotate the encoder faster.
Additional option for when Control is set to ‘NoContrl’:
LABEL: If a control is not assigned to send a MIDI message then there will be a blank space above it on the display.
You can however use that blank space to display up to 8 characters (on the top line of the display) by setting DispType
to ‘LABEL. If this is set, the control name will be displayed, even though the control is not assigned to anything. You can
edit the control name by scrolling up to the second page of options in Edit mode (see below for further info on editing
control names).
Value Range: These options allow you to set the upper and lower limits of the control value. By default the Low Value will
be set to the lowest possible value and the High Value will be set to the highest possible value. In this case the control will
affect a parameter throughout its whole range. Adjust these settings if you want the control on the SL MkII to affect a
parameter though only part of its range.
The range of values allowed for both of these settings will depend on the DispType setting as follows:
With an encoder or pot, the control value will scale from the Low Value to the High Value as you rotate it clockwise.
Consequently if you want the control value to increase as you rotate the encoder clockwise, make sure the High Value is
larger than the Low Value. If you want the control value to decrease as you rotate the encoder clockwise (inverted action),
make the Low Value larger than the High Value. It is possible to invert the action of the sliders, joystick, X-Y touchpad and
the expression pedal in this way.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Novation SL MKII bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Novation SL MKII in de taal/talen: Engels als bijlage per email.

De handleiding is 4,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Novation SL MKII

Novation SL MKII Gebruiksaanwijzing - Deutsch - 37 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info