12
17
Speed/Pace display—
This display shows the
speed of the walking
belt and your current
pace (pace is measured
in minutes per mile).
Every seven seconds, the display will change
from one number to the other.
Note: The console can
display speed and dis-
tance in either miles or
kilometres. To find
which unit of measure-
ment is selected, hold
down the Stop button whilst inserting the key into
the console. An “E,” for English miles, or an “M,”
for metric kilometres, will appear in the Speed/
Pace display. Press the Speed
▲▲
button to change
the unit of measurement. When the desired unit of
measurement is selected, remove the key and
then reinsert it. Note: For simplicity, all instructions
in this manual refer to miles.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
Measure your heart rate, if desired.
To measure your
heart rate, stand
on the foot rails
and place your
hands on the metal
contacts on the
handrail. Your
palms must be rest-
ing on the upper
contacts, and your
fingers must be
touching the lower
contacts—avoid
moving your
hands. When your pulse is detected, the Heart
Rate indicator will flash, three dashes
(– – –) will appear in the Heart Rate/Calories dis-
play, and then your heart rate will be shown. For
the most accurate heart rate reading, continue
to hold the contacts for about 15 seconds.
When you are finished exercising, stop the
walking belt and remove the key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to 1%. The incline
must be at 1% when the treadmill is raised to
the storage position or the treadmill will be
damaged. Next, remove the key from the console
and put it in a secure place. Note: If the displays
and indicators on the console remain lit after
the key is removed, the console is in the
“demo” mode. Refer to page 21 and turn off the
demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
HOW TO USE PRESET PROGRAMS
Insert the key fully into the console.
See GETTING STARTED on page 10.
Select one of the three preset programs.
When the key is inserted,
the manual mode will be
selected and the Manual
indicator will light. To se-
lect one of the preset
programs, press the
Select Program button
repeatedly until the P1, P2, or P3 indicator lights.
When you select a preset program, the program
display will show a simplified profile of the pro-
gram you have selected. For example, the profile
above shows that the intensity of the selected pro-
gram will be greater during the middle of the pro-
gram and less during the beginning and end. The
Time/Laps display will show how long the program
will last.
Press the Start Program button or the Speed
▲▲
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
3
2
1
7
6
Program Indicator
HOW TO CONNECT YOUR HOME STEREO
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adaptor.
Plug the adaptor into the LINE OUT jack on your
stereo.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adaptor.
Plug the adaptor into an RCA Y-adaptor (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA Y-adaptor. Plug the RCA Y-adaptor into the
LINE OUT jack on your stereo.
HOW TO CONNECT YOUR COMPUTER
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adaptor
(available at electronics stores). Plug the Y-adaptor
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adaptor.
