Handleiding Nokta Makro Invenio (pagina 9 van 36) (Engels)

801544

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

3) The location and the angle of the sensor must be adjusted properly

according to the coil being used.

NOTE : When the INV56 search coil is attached to the device, the

message ''Attach the sensor to the 2nd hole!'' will appear on screen.

When mounting the INV56 coil to the shaft, if you have left the sensor

angle at the red line and not aligned it to the blue line, the sensor's field

of view will be restricted by the search coil as shown in the picture.

In such a case, unscrew the sensor and re-attach it so that the blue

lines are aligned as shown in the image. Then you can press the OK

button to clear the message. If you remove the INV56 coil and attach

the INV28 or INV40 coil, this time the message ''Attach the sensor to

the 1st hole!'' will appear.

4) The sensor's lens must be clean. Any dust, mud etc. on lens will

restrain the device from obtaining accurate data.

5) The height of the sensor above the ground must be minimum 25cm.

(10'') - maximum 80cm. (31.5''). The recommended height is between

30cm.- 50cm. (≈12''-20'').

6) Pay attention to keeping your feet away from the sensor's field of

view.

7) The sensor may not work accurately on snow.

8) Using the sensor on flat, smooth surfaces (such as tiles or wood

floor) in places such a home or an office may yield wrong results.

9) Once the sensor is calibrated, changing the angle of the sensor or

the search coil will result in obtaining inaccurate data.

10) During sunny days, if the shadow of the sensor falls in front of the

coil, the sensor will not work. In such a case, you may try extending the

shaft length. If the sensor is still not working, you need to change your

direction to avoid the sunlight.

11) The sensor may not obtain accurate data if the shaft & handle

battery is low.

The IPTU unit, with the help of the

integrated sensors, computes the right-left,

forward-back movements of the search coil

precisely and determines its location and

height above the ground.

With the IPTU sensor, you can follow the

start and finish points of the scanned area

and view the locations of detected targets.

In addition, you can determine the width and

the length of the scanned area, the target

depth and shape as well as the dimensions

with the help of the IPTU sensor.

USAGE OF THE IPTU SENSOR

Correct usage of the IPTU sensor is critical in terms of the device's

performance. The sensor must be used correctly in order for the device

to accurately process the shapes, depth and dimensions of targets and

display them on screen.

At initial start up, the IPTU sensor will be on by factory default. Based

on the type of coil attached to the device, the location and angle of the

sensor must be adjusted. It must also be parallel to the ground.

To determine whether the IPTU sensor is working properly or not, you

need to observe the coil movements on the screen. As you move the

search coil, the coil on the screen should move in the same direction

as well. If you cannot see the actual movements of the search coil on

screen, there may be 3 reasons for this :

1. The sensor may not have been calibrated at all or may have been

calibrated inaccurately.

2. If the ground consists of a single color and has no texture to it (such

as land covered with snow) the sensor may not work properly.

3. In cases where the shadow of the sensor falls in front of the search

coil, the sensor may not work properly.

THINGS TO PAY ATTENTION TO WHILE USING THE IPTU

SENSOR :

1) First, adjust the shaft length and coil angle to searching position.

Then place the search coil on a flat surface, adjust the search coil angle

so that it is parallel with the ground and lean it against a fixed object

such as a tree, rock or a wall. If there is no place to lean it against, hold

it stable with your hand.

2) You must calibrate the sensor before each use or if you have

changed its angle. The calibration process must be performed on a

flat surface. You can find more details on calibration in the further

sections of the manual.

IPTU SENSOR (Integrated Positional Tracking Unit)

90°90°

30cm30cm

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Nokta Makro Invenio Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Nokta Makro Invenio

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info