Handleiding Nokta Makro Invenio Pro (pagina 27 van 36) (Engels)

801545

27

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

The threshold in this mode is internal and cannot be adjusted by the

user. Changes in the ground and temperature may lead to drifts in the

threshold. Threshold drifts will be reflected in the bar at the bottom

either in the negative way (in the DRIFT direction) or the positive way

(in the METAL direction). The device emits an audible response in the

positive drifts and shows the target signal. To differentiate between a

positive drift and a metal signal, pay attention to the tone as well as

the signal graph. If the audio response as well as the signal graph are

stretching out uninterruptedly, the chances that the signal is a positive

drift, are high.

During negative drifts, on the other hand, the bar will fill up in the

DRIFT direction but the device will not emit any sounds. To eliminate

drifts, pull the trigger towards you once and release it to manually

retune the device. Retuning periodically while searching in this mode

is recommended.

In the Basic mode, if the drifts are substantial and retuning does not

improve the situation, drop the sensitivity gradually and re-ground

balance. If the drifts continue, switch to Expert or one of the other

modes to continue your search.

Expert

This mode is designed for more experienced users. Although it works

the same as the Basic mode in principle, its advanced settings allow

for a deeper and more stable search on all kinds of terrains.

In Expert mode, too, the device will generate the same audio tone for all

targets and it will display the target ID on screen. At the same time, the

target ID will be shown on the color ID scale at the top with the cursor.

In Expert mode, the target ID range is 00-99. 00-40 are ferrous metals

and 41-99 are gold/non-ferrous metals. In this mode, you can use the

Discrimination setting and discriminate out all IDs between 0 and the

set Discrimination value and search while ignoring these targets.

The threshold in this mode is internal and cannot be adjusted by the

user. Changes in the ground and temperature may lead to drifts in the

threshold. Threshold drifts will be reflected in the bar at the bottom

either in the negative way (in the DRIFT direction) or the positive way

(in the METAL direction). The device emits an audible response in the

positive drifts and shows the target signal. To differentiate between a

positive drift and a metal signal, pay attention to the tone as well as

the signal graph. If the audio response as well as the signal graph are

stretching out uninterruptedly, the chances that the signal is a positive

drift, are high.

During negative drifts, on the other hand, the bar will fill up in the

DRIFT direction but the device will not emit any sounds. To eliminate

drifts, pull the trigger towards you once and release it to manually

retune the device. Retuning periodically while searching in this mode

is recommended.

In the Expert mode, if the drifts are substantial and retuning does not

improve the situation, please read the section about the Stabilizer

setting in the manual.

Ground Anomaly & Cavity

This mode is designed to detect the changes and anomalies in the

ground, as well as underground cavities, such as rooms, tunnels, and

cellars. The results obtained in this mode are directly associated

with the operator's experience level with metal detectors. Evaluating

and interpreting the signals in this mode requires relatively more

practice to other modes. The device can also detect metals in this

mode. However, it is recommended that this mode should not be used

for general metal detection but only in places where you suspect the

presence of a cavity.

This mode works with the detection screen with IPTU sensor only,

and it is a silent mode. In other words, the device does not generate

an audio response upon detection of an anomaly or a cavity.

24

SEARCH MODES

INVENIO has 6 search modes, designed for different terrains and

targets. 3 of these modes are static (Basic, Expert and Ground Anomaly

& Cavity) and 3 are dynamic (All Metal, Fast and Deep) modes.

Static modes are non-motion modes. In other words, the device will

generate an audio response when you hold the coil stationary without

swinging over the target. The audio response increases in volume as

the coil approaches the target. These modes are recommended for

larger and deeper metals.

Dynamic modes, on the other hand, are motion modes. You must

sweep the search coil from side-to-side to detect metal. If the search

coil does not move, the device will not provide any audio responses

even if the coil is over a metal target. These modes are used to detect

smaller targets such as coins.

The device will start in Basic mode upon initial start up. To change the

search mode, press the SETTINGS button and select MODE. You can

navigate between the modes using the right and left buttons and select

the one you wish.

All modes, except for the Ground Anomaly & Cavity, will work in both

screens. The Ground Anomaly & Cavity mode will work in the detection

screen with the sensor only. Detection screen selection does not have

direct effect on the operation of the modes. The main difference between

the 2 screens is as follows: When searching in the detection screen

without the IPTU sensor, the device detects targets and displays their

IDs only. On the other hand, while searching in the detection screen with

the IPTU sensor, apart from the IDs, the device also provides the instant

depth, shape and 3D graphs of detected targets.

Non-Motion Modes

IMPORTANT! For a more stable operation, try keeping the coil

consistently at the same height above the ground where you retuned

the detector.

IMPORTANT! If you retune the detector over metal, the drift will be in

the negative side (in the DRIFT direction on the Drift-Metal bar at the

bottom of the screen) and the device will no longer detect the target

until the detector is retuned. In addition, the depth of the detector will

also decrease.

IMPORTANT! In non-motion modes, ground balancing is very important

for a deeper and more stable detection. It is recommended that you

should follow the ground balance window and re-ground balance your

device based on instant ground balance changes.

Basic

This mode is designed for beginners. It does not require much

adjustment and can be used by adjusting the sensitivity setting only.

In Basic mode, the target ID range is 00-99. 00-40 are ferrous metals

and 41-99 are non-ferrous metals. In this mode, ferrous metals with ID

numbers between 0 and 40 are discriminated out by factory default.

Upon target detection in Basic mode, the bar at the bottom of the

screen will fill up to the right, in the METAL direction in proportion to

the strength of the signal.

In Basic mode, the device will generate the same audio tone for all

targets but it will display the target ID on screen. At the same time,

the target ID will be shown on the color ID scale at the top with the

cursor.

For more details, please read ''Searching in Ground Anomaly & Cavity

Mode''.

Motion Modes

All Metal

Different than the Fast and Deep modes, this mode features a

threshold tone which is continuously heard in the background.

All Metal mode is used in 2 different ways in the INVENIO: 1) with the

Discrimination setting disabled at 0 2) with Discrimination enabled

(non-zero). When the device is first turned on, Discrimination setting

will be off. When the Discrimination is set at 0, the device does not

discriminate targets and detects all targets (metals, mineralized rocks

etc.). ID of the detected target is shown on the display (except for

negative hot rocks) and the same audio tone is provided for all targets.

The audio tone increases in pitch as the coil approaches the target.

When using the Discrimination setting in this mode, the device will emit

a low ferrous tone for all targets below the adjusted Discrimination

setting level, and a higher tone for all targets above the Discrimination

setting which changes in pitch as the coil approaches the target. Let's

say you set the Discrimination to 20. The device will generate a low

iron tone for all metals with 0-20 ID and a higher tone for all targets

with 21-99 ID. Upon target detection, the threshold will momentarily go

silent and only the target audio response will be heard. The duration of

the threshold's silence is directly related to the level of the Stabilizer.

Sensitivity, Threshold and Stabilizer settings in this mode are optimized

to provide the best performance on different terrains. You can modify

these settings based on ground conditions.

We recommend using the All Metal mode when discrimination is not

important and not using it in heavy trash areas.

Fast Mode

This is the 3-tone discrimination mode designed for coin hunting

especially in trashy sites such as parks. In this mode, the device

produces a low tone for ferrous targets with 0-40 IDs, a medium tone

for gold and non-ferrous metals with IDs 41-66 and a high tone for

non-ferrous metals with IDs 67-99 such as silver, brass and copper.

By using the Tone Break feature, you can adjust the break points of

the target response tones on the Target ID range.

In this mode, you can use the Discrimination setting to ignore unwanted

targets. The Discrimination default value is set to 10. We recommend

you to change this value according to the type of targets you are

searching for.

Deep Mode

Recommended especially for relic hunting. Due to its depth, this mode

is a bit noisier than the other modes. However, due to the design

characteristics of this mode, the noise will be more in the air versus

in the ground. Take this fact into consideration when adjusting the

sensitivity level.

In this mode, the device produces a low tone for ferrous targets with

IDs between 0-40. For targets with IDs 41-99, it produces a higher

tone which increases in pitch as the coil approaches the target. By

using the Tone Break feature, you can adjust the break points of the

target response tones on the Target ID range.

In this mode, too, you can use the Discrimination setting to ignore

unwanted targets. The Discrimination default value is set to 10. We

recommend you to change this value according to the type of targets

you are searching for.

IMPORTANT! You cannot get result screens, meaning 3D graphs, in

motion modes.

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nokta Makro Invenio Pro bij:

nieuwe vragen en antwoorden
nieuwe handleidingen

U ontvangt een email met instructies om u voor één of beide opties in te schrijven.

Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nokta Makro Invenio Pro in de taal/talen: Engels als bijlage per email.

De handleiding is 5.71 mb groot.

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Nokta Makro Invenio Pro

Nokta Makro Invenio Pro Gebruiksaanwijzing - Türkiye - 36 pagina's

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.

Info