Turn the rotary control to “MAINTENANCE” and press it.
Turn the rotary control to “RINSE FROTHER” and press it.
The display shows “CONNECT HOSE TO SPOUT AND DRIP TRAY”.
Connect the hose to the spout (g. 7).
Connect the other end to the back of the drip tray (g. 10).
Place a sufciently large bowl (about 0.5 l) under the spout.
Press rotary control.
The display shows “RINSING FROTHER, DO NOT REMOVE HOSE”. The appliance then starts the
cleaning process. Once the process is nished the appliance reheats and is ready for use. The display
shows the main menu.
5.2. System rinsing
From time to time the system should be rinsed. Proceed as follows:
Turn the rotary control to “MAINTENANCE” and press it.
Turn the rotary control to “SYTEM RINSING” and press it.
The display shows “RINSING SYSTEM”.
Once the process is nished, the appliance reheats and is ready for use. The display shows the main
menu.
5.3. Cleaning frother
Attention: Do not disrupt the running program!
Note: The display shows “PLEASE CLEAN FROTHER” when it is required.
Proceed as follows:
Turn the rotary control to “MAINTENANCE” and press it.
Turn the rotary control to “CLEAN FROTHER”.
The display shows “EMPTY TRAYS” and “FILL WATER” alternatingly.
Remove drip tray with used coffee container (g. 1/N and 1/O) and empty both.
If necessary rell the water tank with fresh water. Reinsert the water tank rst, followed by drip
tray and used coffee container.
The display shows “CONNECT HOSE TO SPOUT AND IN CLEANER”.
Connect the hose to the spout (g. 7).
Put some detergent (available as an optional accessory, see 8.) and water in a container, both
should amount to 0,3l. For the correct mix refer to instructions by the detergent’s manufacturer.
Dip the other end of the hose into the cleaning solution
Place a sufciently large bowl (minimum contents 0.5 l) under the spout.
Press the rotary control.
The display shows “START CLEANING”.
Press the rotary control.
The cleaning process is started. The display shows “CLEANING FROTHER. DO NOT REMOVE
HOSE”.
After a short while the display shows “CONNECT HOSE TO SPOUT AND DRIP TRAY”.
Connect the hose to the spout (g. 7) and the other end to the drip tray (g. 10).
Press the rotary control.
The display shows “CLEANING FROTHER, DO NOT REMOVE HOSE”.
Once the cleaning cycle is nished, the appliance starts heating up and is again ready for use.is
complete.
Empty the drip tray and used coffee container (g. 1/N and 1/O) and re-insert them cleaned.
The display shows the main menu.
5.4. System cleaning
Note: If the appliance needs cleaning, the display will show “PLEASE CLEAN SYSTEM”. You can continue
making coffee, but we recommend starting the cleaning program as soon as possible. Otherwise the func-
tion might be impaired and your warranty could be compromised.
Attention: Do not disrupt the cleaning process. Insert cleaning tab only if the appliance asks for it.
Turn the rotary control to “MAINTENANCE” and press it.
Turn the rotary control to “CLEAN SYSTEM” and press it.
The display shows “EMPTY TRAYS” and “FILL WATER” alternatingly.
Remove drip tray and used coffee container (g. 1/N and 1/O) and empty both.
If necessary rell the water tank with fresh water. Reinsert the water tank rst, followed by drip
tray and used coffee container.
The appliance rinses twice and the display shows “CLEANING SYSTEM”.
The display shows “CLEANING TAB IN GROUND COFFEE CHUTE”.
Place a sufciently large bowl (minimum contents 0.5 l) under the spout (g. 1/E).
Open the lid on the right hand side of the appliance (g. 1/G).
Open the lid of coffee powder chute (g. 1/M).
Place a cleaning tab in the chute and close both lids.
The display shows “START CLEANING”.
Press the rotary control to conrm.
The appliance starts the cleaning process. The display shows “CLEANING SYSTEM”. The fully auto-
mated process takes approximately 10 minutes.
Note: Should a message appear during the cleaning process, follow the indicated steps. The appliance
will continue with the cleaning automatically afterwards.
Once the process is nished, the display shows “EMPTY TRAYS“
Remove drip tray with used coffee container (g. 1/N and 1/O), empty both and reinsert them.
If necessary rell the water tank with fresh water. Reinsert the water tank rst, followed by drip
tray and used coffee container.
The appliance rinses, reheats and is ready for use after that. The display shows the main menu.
5.5. Descaling
If the appliance needs descaling, the display shows “PLEASE DESCALE SYSTEM”.
You can also start the descaling programme any time manually.
Attention: Please make sure to follow each step exactly as outlined below! You can continue making
coffee, but we recommend starting the descaling program as soon as possible. Otherwise the function
might be impaired and your warranty could be compromised.
Attention: Do not disrupt the descaling program. Never use vinegar or vinegar-based agents, only
standard liquid products specically recommended for automatic coffee machines.
Attention: Before starting the descaling program remove the lter from the water tank.
Turn the rotary control to “MAINTENANCE” and press it.
Turn the rotary control to “DESCALING SYSTEM” and press to conrm.
The display shows “EMPTY TRAYS”.
Remove drip tray with used coffee container (g. 1/N and 1/O), and empty both.
Reinsert drip tray and used coffee container.
52 53
5. Cleaning and maintenances 5. Cleaning and maintenance
