22352200. Replacing the Motor/Fan unit A-0.6.5
22352400. Replacing the internal wires for one speed motor 25
22352500. Replacing the internal wires for two speed motor
22352700. Replacing the Motor suspension
22354000. Replacing the Motor tube
22354100. Replacing the suction house
ASSEMBLY INSTRUCTIONS KING 500 SERIES
Instruction No. 82362500/00-08
To be performed by a skilled
or instructed person only !
Disconnect the vacuum cleaner
from the power supply before
starting the work!
Follow instruction 82362200 first
1,2,3
How to disassemble the
machine.
Loosen the four screws (16) for the
HEPA filter in the bottom housing
by turning them through 90
degrees using a coin (17). Pull out
the tube (18) with your fingertips.
To separate the top and buttom
housing and avoid scratches on
the parts, place tool no. 22361400
under the buffer.
Follow instruction 82361500
Remove the strap by hand and lift
away the top housing.
Replacing the motor/fan unit
22352200.
Replacing the motor suspension
22352700.
Replacing the motor tube
22354000.
Disassemble the machine.
Remove the wires from the two ter-
minal spades (23) and press down
to free them from the rubber gas-
kets, unscrew the six screws (22)
from top and pull out the motor
tube (20) with the two red internal
wires.
Remove and replace the motor/fan
(25) unit with rubber suspension
(27-28-29-30) and/or internal red
wires.
When replacing the internal wires
wrap them around the two small
fixtures (32) on the motor suspen-
sion (28). When replacing with new
motor suspension parts, press by
hand to click item 27 & 28 together
(29), before mounting onto the
motor/fan unit.
Before replacing the motor tube
(20), place the two-rubber gaskets
(26) with the slots in opposite posi-
tion and with the terminal spades
(23) pulled back into the rubber
gaskets (26).
Replace the motor/fan unit (25)
with the bow tie formed motor sus-
pension (29) turned to fit to the
same form (31) in the bottom of the
tube (20). Mount the motor tube
(20) unit with internal red wires to
the suction house (19) with the six
screws (22).
Replace the internal wires
according to wiring diagram.
Refit in reverse order.
Removal and replacement of the
suction house (19), 22354100
Disassemble the machine.
Unscrew from top the screw (11)
for the wheel with a Torx T 20
screwdriver and remove the shaft
with wheel from the bottom side.
Unscrew the five screws (10) in the
bottom to release it from the suc-
tion house (19) and replace the
gasket (15) on the new suction
house(19).
Unscrew the six screws (22) from
top and pull out the motor tube
(20) with the two internal wires. Be
sure to remember the upper motor
suspension (30).
Remove and replace the On/Off
parking switch.
To release the switch, hold the
activator pin (7) with one hand and
release the switch (8) from the two
hooks and pull it away. Remove
and replace the pin (7) with spring
into the bush of the housing.
Remove and replace the cords to
the switch (8).
Replace pin (7) by pushing it
downward to give the switch (8)
lever access to the hole in the pin
(7) and mount the switch (8).
Remove and replace the On/Off
switch, Two speed PCB and inter-
nal wires (5-6).
Mount the wheel with shaft by the
use of a small screwdriver and a
Torx T 20 screwdriver.
Mount shaft into wheel and place a
small screwdriver through the hole
for the metric screw. Push wheel
with shaft and a small screwdriver
into the groove for wheel from the
bottom side with small screwdriver
pointing through the metric hole.
When screw (11) is positioned from
the upper side, the screw (11) will
push out the small bottom screw-
driver.
Refit in reverse order.
Assembling of the machine
Position the upper part on the bot-
tom part, replace the strap (12)
between the hooks and press by
hand the buffer (13) until it snaps
the two parts together.
