Handleiding Nikon Callaway id TECH (pagina 1 van 2) (Engels)

604476

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

NIKON VISION CO., LTD.

Customer Service Department

3-25, Futaba 1-chome, Shinagawa-ku, Tokyo 142-0043, Japan

Tel: +81-3-3788-7699 Fax: +81-3-3788-7698

Printed in China (197K)/1E

CAUTIONS BEFORE USE

Please observe the following guidelines strictly so you can use the equipment properly

and avoid potentially hazardous problems. Before using this product, read thoroughly the

“SAFETY AND OPERATION PRECAUTIONS” and instructions on correct usage

accompanying the product. Keep this manual within reach for easy reference.

WARNING

This indication alerts you to the fact that any improper use ignoring the contents

described herein can result in potential death or serious injury.

CAUTION

This indication alerts you to the fact that any improper use ignoring the contents

described herein can result in potential injury or material loss.

SAFETY AND OPERATION PRECAUTIONS

Warning

•

Never look directly at the laser beam or directly at the sun when using the Nikon

Callaway id TECH.

• DonotdepressthePOWERbuttonwhilelookingintotheopticsfromtheobjectiveside.

• Donotaimattheeye.

• Donotoperatetheunitwithotheradditionalopticalelements,suchaslensesor

binoculars. Using an optical instrument together with the Nikon Callaway id TECH

increases the danger of damaging the eyes.

• DonotdisassembletheNikonCallawayidTECH.Aproductthathasbeendisassembled

is not guaranteed by the manufacturer.

•

WhentheNikonCallawayidTECH’sbodycoverisdamaged,orifitemitsastrange

sound due to dropping or for some other cause, immediately remove the

battery and stop using.

Cautions

• WhennotusingtheNikonCallawayidTECH,donotpushthePOWERbutton.

• DonotleavetheNikonCallawayidTECHwithinthereachofsmallchildren.

• Rain,water,sandandmudshouldberemovedfromtherangefinderbodysurfaceassoon

as possible, using a soft, clean, dry cloth.

• AlthoughtheNikonCallawayidTECHiswaterproof,itisnotdesignedforuse

underwater.

• DonotswingtheNikonCallawayidTECHbyitsstrap.Itmayhitsomeoneandcause

injury.

• DonotleavetheNikonCallawayidTECHinanunstableplace,asitmayfallandcause

injury, or damage the equipment.

• DonotlookthroughtheNikonCallawayidTECHwhilewalking.Youmaywalkinto

something and get hurt.

• DonotleavetheNikonCallawayidTECHinacaronahotorsunnyday,ornearheat-

generating equipment. This may damage or negatively affect it.

• DonotleavetheNikonCallawayidTECHindirectsunlight.Ultravioletraysand

excessive heat may negatively affect or even damage the unit.

• WhentheNikonCallawayidTECHisexposedtosuddenchangesintemperature,water

condensation may occur on lens surfaces. Do not use the product until the condensation

has evaporated.

• Donotusealcoholforcleaningthemainbody.

• Donotleavethepolyethylenebagusedforpackagingwithinthereachofsmallchildren.

• Becarefulthatsmallchildrendonotinadvertentlyswallowtheeyecup.Ifitdoeshappen,

consult a doctor immediately.

• Ifyouusetherubbereyecupforalongperiodoftime,youmaysufferskininflammation.

If you develop any symptoms, consult a doctor immediately.

• WhencarryingtheNikonCallawayidTECH,storeitinthesoftcase.

• IfyourNikonCallawayidTECHshouldfailtooperatecorrectly,discontinueuse

immediately and consult the Troubleshooting Table. If you are unable to fix the problem,

contact your local dealer for instructions on where to send it for repair.

CARE AND MAINTENANCE

Lenses

• Whenremovingdustonthelenssurface,useasoftoil-freebrush.

• Whenremovingstainsorsmudgeslikefingerprintsfromthelenssurface,wipethelenses

very gently with a soft clean cotton cloth or quality oil-free lens tissue.

Use a small quantity of pure alcohol (not denatured) to wipe stubborn smudges. Do not

use velvet cloth or ordinary tissue, as it may scratch the lens surface. Once the cloth has

been used for cleaning the body, it should not be used again for the lens surface.

Main body

• Cleanthebodysurfacewithasoft,cleanclothandadrycloth.Donotusebenzene,

thinner, or other organic agents because they may cause discolouration or rubber

degeneration.

Storage

• Watercondensationormouldmayoccuronthelenssurfacebecauseofhighhumidity.

Therefore, store the Nikon Callaway id TECH in a cool, dry place.

After use on a rainy day or at night, thoroughly dry it at room temperature, then store in a

cool, dry place.

NOTES ON LITHIUM BATTERY

If handled incorrectly, batteries may rupture and leak, corroding equipment and staining

clothing. Be sure to observe the following:

• Installbatterieswiththe+and–polespositionedcorrectly.

• Batteriesshouldberemovedwhenexhaustedorduringextendedperiodsofnon-use.

• Alwaysusethesamebrandofbattery.

• Ifbatteryfluidcontactseyesorskin,rinsewellwithwater.Ifswallowed,consultadoctor

immediately.

• Donotshort-circuitbatterychamberterminals.

• Donotcarrybatteriestogetherwithkeysorcoinsinapocketorbag.Thismayoverheat

and short-circuit batteries.

• Donotputbatteriesinfireorwater.Neverdisassemblebatteries.

• Donotchargebatteries.

• Donotsubjectstoredbatteriestoextremesintemperature.

• Donotsubjectbatteriestostrongvibrationsorshock.

Key Features

Body .............................................x1

Soft case ......................................x1

Neckstrap .....................................x1

Lithium battery (CR2) ....................x1

Composition

• Lineardistancemeasurementrange:10-500meters/11-550yards/33-999feet

• Anglemeasurementrange:±89°

• Distancemeasurementdisplaystep:

[Internal Display]:

(Linear Distance)

0.5 meter/yard, 1 foot

(measurement distance is less than 100 meters/yards/feet)

1.0 meter/yard, 1 foot

(measurement distance is 100 meters/yards/feet or farther)

(Horizontal Distance/Height)

0.2 meter/yard, 0.5 foot

(measurement distance is less than 100 meters/yards/feet)

1.0 meter/yard, 1 foot

(measurement distance is 100 meters/yards/feet or farther)

(Angle)

  0.1°(-10°ー10°)

 1.0°( ≦ -10°,10° ≦ )

[External Display]:

(Linear distance) 0.5 meter/yard, 1 foot

(Horizontal Distance/Height) 0.2 meter/yard, 0.5 foot

(Angle)    0.1°

• Easy-to-aim6xopticalobservationsystem

• Quantifiesthehorizontaldistancetothetargetanditsheightinrelationtothe

rangefinder's level by measuring linear distance and angle.

• Measuretheverticalseparation(heightbetweentwopoints).

• TheresultsaredisplayedonbothaninternalandanexternalLCDpanel.The

external LCD panel shows all results simultaneously.

• MeasureanddisplayinFirstTargetPriority.

• Waterproofdesign(NOTdesignedforunderwaterusage)

• Invisible/EyesafeIECClass1MLaser

• 30-secondresultsdisplay

• Compact,lightweight,ergonomicdesign

• Automaticshut-off(afterapprox.30sec.unattended)

• Defaultto“LastUse”settings

• 20-secondcontinuousmeasuringfunction

The Nikon Callaway id TECH emits invisible, eyesafe, infrared energy pulses

that reflect off the selected target back to its optical receiver. Sophisticated

precision charge circuitry is used to instantaneously calculate distances, by

measuring the time it takes for each pulse to travel from the rangefinder to the

target and back. Laser reflectivity and measurement results may vary according

to climatic and environmental conditions, the colour, surface finish, size, shape

and other characteristics of the target.

The following factors ensure best range and accuracy:

• Nighttimeuse

• Cloudyweather

• Bright-colouredtargets

• Targetswithhighlyreflectivesurfaces

• Targetswithshinyexteriors

• Large-sizetargets

• Shootingtargetsfacingat90degrees

Measurement may result in inaccuracy or failure in the following cases:

• Slenderorsmalltarget

• Targethasdiffusingreflectivesurface

• Targetdoesnotreflectthelaserbeam(glass,amirror,etc.)

• Blacktarget

• Targethasvaringdepths

• Insnow,rainorfog

• Targetmeasuredthroughglass

• Reflectivesurfacemeasuredfromdiagonaldirection

• Movingtarget

• Obstaclemovinginfrontofthetarget

• Whentargetingthesurfaceofwater

Nomenclature

Monocularobjectivelens/

Laser emission aperture

Laser detector aperture

External LCD

MODEbutton

POWERbutton

6x monocular eyepiece

Eyecup/diopter adjustment ring

Diopter index

Strap eyelet

Battery chamber cover

Battery chamber cover “Open/

Close” indication

Product number/explanatory label

Laser warning label

Internal Display

1. 『』- Target focusing/Laser irradiate system

『

』-

Aim at the target. Position the target

at the center of the reticle.

『

』- Appears while the laser is being used

for a measurement. (Remains present during

single measurement.Blinks during continuous

measurements.)

Warning: Do not look into the objective lenses

when this mark is shown.

2．『

』: Distance/measurement status display

Digitally indicates measured distance in meters/yards/feet and angles in

degrees. Also indicates measuring status such as “Measurement in

progress”, “Measurement unsuccessful” or “Unable to measure.”

(Distance)

Display of results: ( ≧ 100m/yards/feet) e.g. 234 meters =

『

』

Display of results: ( ＜ 100m/yards) e.g. 76.5 yards = 『

』

Display of results: ( ＜ 100 feet) e.g. 82 feet = 『

』

(Angle)

Display of results: ( ≦ -10˚ and ≧ 10˚) e.g. 36˚=『

』

e.g. -29˚=『

』

Display of results: (-10˚＜ and ＜ 10˚) e.g. 3.5˚=『

』

e.g. -7.0˚=『

』

『

』- Now measuring

『

』- Failure to measure or unable to measure distance

3. 『

』

Display Units

『

』Indicates distance being measured in meters.

『

』Indicates distance being measured in yards.

[No unit displayed]　Indicates distance is measured in feet.

4. 『

』- Indicates battery condition. (See "Changing Batteries")

5. 『

』Display Modes

(See “Measurement and Display” for operations and display examples.)

Linear distance mode

『

』Calculates linear distance to your target and displays the results.

Horizontal distance mode

『

』 Calculates horizontal distance to your target by measuring

the linear distance and angle, and displays the results.

Height mode

『

』 Measures your target's height from the horizontal level, and

displays the results.

Vertical separation (height between two points) mode

『

』 Uses the linear distance and angle data of two points to

calculate and display the vertical separation (height

between the two points.)

Angle mode

『

』 Measures the angle of your target from the horizontal level

and displays the results.

Although the LCD was produced using the most advanced technology, it is

impossible to eliminate dust completely. When using this product, the LCD is

magnified by high magnification of the eyepiece lens and dust may appear as

a defect. It will not, however, affect measurement accuracy.

Operational Summary

Caution—use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure

1. Install a battery in the battery chamber. (See Changing

Batteries)

2. Rubber eyepiece cup

Eyeglass wearer: Collapse the eyepiece cups.

Non-eyeglass wearer: Do not collapse the eyepiece cups.

3. Diopter adjustment

Adjust diopter to obtain a clear image in the LCD.

First, rotate the diopter adjustment ring counterclockwise until it comes to a

complete stop. Next, turn on the power to activate the LCD when you look

through the Nikon Callaway id TECH. Rotate the diopter adjustment ring

clockwise until the display comes into focus.

If the diopter is not adjusted to correspond to your eyesight, you may not be

able to clearly focus your subject.

4. Measuring

Note: See separate “Measurement and Display” sheet for external LCD panel.

Note: Depressing and holding down the POWER button causes all symbols to be

displayed in the internal LCD panel. After you remove your finger from the

POWER button, the last-used setting is displayed. (If you briefly press the

POWER button then remove your finger, the LCD panel may display the last-

used setting without displaying all of the symbols. This is not a malfunction

or other problem.)

Before measuring, be sure to confirm settings, such as unit, measurement/display

mode and priority mode.

◎: See the relevant mode section in this manual for setting.

Changing Batteries

Type of battery: 3V CR2 lithium battery

Battery condition indicators

: Battery has enough charge for use.

: Battery charge is getting low.

flashing: Battery charge is low and battery

should be replaced.

disappears: Battery is exhausted and should

be replaced.

flashing in the LCD indicates that the battery should be replaced.

1 Open the battery chamber cover

Using the ball of the thumb or a coin in the recessed part of the battery

chamber cover, rotate the cover following the Open/Close arrow indicator. It

may not open easily due to its rubber packing for water resistance.

2 Replace the old battery with a new one

Install new battery with the [+] and [-] correctly positioned following the

“Battery installation” indication seal in the battery chamber. (Insert battery

positioning the [+] pole towards the inside of the chamber.) [The Nikon

Callaway id TECH will not operate if the battery is installed incorrectly.]

3 Close the battery chamber cover

Align the Open/Close indicator with the white dot and insert the battery

chamber cover. Using the ball of the thumb or a coin, turn the cover in the

opposite direction to the arrow indicator. It may not close easily due to the

rubber packing for water resistance, but continue to turn it all the way until

it stops. Confirm that the cover is securely closed.

Battery life

Continuous operation:

Approx. 10,000 times (at 20°C)

Target focusing, measurement, and automatic power off are included in a

single cycle. This figure may differ according to temperature, and other

factors such as target shape, colour, etc.

* The Nikon Callaway id TECH come with a 3V CR2 lithium battery. However, due to

natural electric discharge, the life of the battery will likely be shorter than that noted

above.

Replace battery if the Nikon Callaway id TECH is ever submerged in water or if water

enters in the battery chamber.

Specifications

Laser Rangefinder

Thank you for purchasing the Nikon Callaway id TECH.

This high-spec laser rangefinder features a new angle measurement function in

addition to the existing linear distance measurement function for enhanced

enjoyment of sports and other outdoor applications. (The Nikon Callaway id

TECH is also able to measure the horizontal distance to a target and its height.)

Please observe the following guidelines strictly so you can use the equipment

properly and avoid potentially hazardous problems. Before using this product,

read thoroughly the “SAFETY PRECAUTIONS” and instructions on correct usage

accompanying the product.

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

Keep this manual within reach for easy reference.

•Specificationsanddesignaresubjecttochangewithoutnotice.

•Noreproductioninanyformofthismanual,inwholeorinpart(exceptforbrief

quotation in critical articles or reviews), may be made without written

authorization from NIKON VISION CO., LTD.

Instruction Manual

Callaway id TECH

POWER

Set FULL/Limited

measurement mode

LCD is illuminated

Set your desired modes

◎

Align the reticle

with the target

POWER

appears

Results are converted to the

mode set and displayed.

MODE

Indication

remains

illuminated for

30 sec.

30 seconds pass without operation ＊

Power off: LCD indications disappear

Measure again

Fail to measure

Cannot measure

Successfully

measured

For continuous distance

and angle measurement

(up to 20 seconds), keep

button depressed.

※

☆

☆【Continuous measurement mode】

Keeping the POWER button depressed allows you to perform

continuous measurement for 20 seconds.

Blinks while performing measurements.

When measuring a pin at a golf course, for example, use Continuous

measurement mode for easy measurement. With no objects between you

and the pin, the smallest number is the distance to your targeted pin.

※ See the “Measurement and Display” sheet for details regarding the

operations and results display of the various modes.“

＊ Power turns off 30 seconds after the last operation.

5. Selecting display unit (Factory default setting is yard.)

Meter [ ]

Yard

[ ]

Feet [ ]

1. Confirm the LCD panel is on.

2. Press and hold the

button for approx. two seconds.

3. When display unit has switched, release the

button.

4. Repeat steps 2 and 3 until your desired mode is displayed.

5. When you have completed setting, results will be converted and displayed

in the your selected measurement unit.

6. Switching measurement/display modes (Factory default setting is

linear distance measurement mode)

Linear Distance [ ]

Horizontal Distance [ ]

Angle [ ]

Height [

]

Vertical Separation

between 2 points point

[ ]

By pressing the MODE button, modes will change in

the order indicated above.

The angles and heights of two points are displayed

only at the full-mode setting.

1. Confirm the LCD panel is on.

2. Press

button within 0.5 seconds.

3. Release

button to switch the mode.

4. Repeat steps 2 and 3 until your desire mode is displayed.

5. Switching the mode after measurement converts the results to the new

mode.

6. After the mode is set, measurements are performed in the new mode.

7. Switching Full/Limited modes (default setting is limited mode)

1. Confirm the power is off (LCD is off).

2. Press and hold

button, then depress and hold button

within 0.5 second.

3. Continue to press and hold both buttons, (more than 2 seconds),to

confirm the internal display is on.

When these buttons are pressed, all symbols are displayed . When

『

』and『』symbols do not appear, Limited mode is

switched to Full mode.

Note） If buttons are not pressed in the correct order, switching will

not take place.

Note） This mode change can also be confirmed when switching the

measurement/display mode.

4. Release buttons.

8. Distance display

Nikon Callaway id TECH is First Target Priority Distance Display System.

When obtaining different results from a single measuring operation. The Nikon

Callaway id TECH will display the distance to the nearest target on the LCD

panel.

ex.) When measuring a tree standing in front of a house;

"115m" (distance to the tree) will be displayed. This mode has application for

golf.

9. Low battery indication

Flashing

indicates that the battery charge is low and battery should

be replaced. (See "Changing Battery")

Optical system

Type Roof-prism monocular

Magnification 6x

Effective diameter of objective lens (mm) ø21mm

Angularfieldofview(real) 6.0°

Eye relief (mm) 18mm

Exit pupil (mm) ø3.5mm

Dioptreadjustment ±4m

-1

Others

Operatingtemperature -10°—+50°

Power source CR2 lithium battery x 1, 3V DC,

Auto Power Off (approx. 30 seconds)

Dimensions(DxWxH) 130x45x69mm

Weight Approx.210g(withoutbattery)

Structure Body:Waterproof(maximumdepthof1meter

for up to 10 minutes)*

（Batterychamber:Waterresistant**）

Safety&EMC Class1MLaserproduct(IEC68025-

1:2001)

FCC Part15 subpart B Class B

 CE,EMCdirective,c-tick,WEEE

* Waterproof models

The Nikon Callaway id TECH is waterproof, and will suffer no damage to the

optical system if submerged or dropped in water to a maximum depth of 1 meter

for up to 10 minutes.

The Nikon Callaway id TECH offers the following advantages:

• Canbeusedinconditionsofhighhumidity,dustandrainwithoutriskof

damage.

• Nitrogen-filleddesignmakesitresistanttocondensationandmold.

Observe the following when using the Nikon Callaway id TECH.

• Astheunitdoesnothaveaperfectlysealedstructure,itshouldnotbe

operated nor held in running water.

• Anymoistureshouldbewipedoffbeforeadjustingmovableparts(eyepiece,

etc.) of the Nikon Callaway id TECH to prevent damage and for safety reasons.

To keep your Nikon Callaway id TECH in excellent condition, Nikon Vision

recommends regular servicing by an authorized dealer.

** The battery chamber is water resistant, not waterproof. Water may enter the

device if the Nikon Callaway id TECH is submerged in water. If water enters

the battery chamber, wipe out any moisture and allow time for the chamber to

dry.

Troubleshooting/Repair

If problems persist after consulting the Troubleshooting Table,

please contact your local dealer to check/repair the Nikon

Callaway id TECH. Never let anyone than the official

representative of the product manufacturer check or repair the

Nikon Callaway id TECH. Failure to follow this instruction could

result in injury, or damage to the product.

Symptom Check Points

Unit does not turn on —

LCD fails to illuminate

Target range cannot be

obtained

[- - -] (“Cannot

measure”) appears

Closer target cannot be

measured

Target beyond a certain

distance cannot be

measured

Measurement result is

unstable

Incorrect result is

displayed

•DepressPOWERbutton.

•Checkandreplacebatteriesifnecessary.

•Besurethatnothing,suchasyourhandorfinger,is

blocking the laser emission aperture and laser

detector.

•Besurethatthelaseremissionapertureandlaser

detector are clean. Clean them if necessary.

•Besurethatthetargetshapeandconditionis

appropriate to reflect the laser beam.

•Replacebattery.

•Besuretoholdtheunitsteadywhiledepressingthe

POWER button.

•Besurethetargetiswithinmeasuringrange(10-

500m/11 - 550 yards/33-999 feet)

•Besurethatnothing,suchasleavesorgrass,is

between the Nikon Callaway id TECH and the target.

•Besurethatnothing,suchasleavesorgrass,is

between the Nikon Callaway id TECH and the target.

•Replacebattery.

•Besurethatthetargetshapeandconditionis

appropriate to reflect the laser beam.

•Besuretoholdtheunitsteadywhiledepressingthe

POWER button.

•Besurethatnothing,suchasleavesorgrass,is

between the Nikon Callaway id TECH and the target.

•Replacebattery.

•Besurethatthetargetshapeandconditionis

appropriate to reflect the laser beam.

•Besurethatnothing,suchasleavesorgrass,is

between the Nikon Callaway id TECH and the target.

If your Nikon Callaway id TECH should require repair, please contact your local

dealer for details regarding where to send it. Before doing so, you are advised to

consult the Troubleshooting Table below.

Do not use the Nikon Callaway id TECH for purposes beyond the limits of its

stated accuracy.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules and to EU EMC

directive. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

•Reorientorrelocatethereceivingantenna.

•Increasetheseparationbetweentheequipmentandreceiver.

•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two condition0s:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Tree Fence House

Distance to Target 115m 123m 128m

MeasurementSystem

Measurementmode Linear distance : Act

display Horizontal distance : Hor

Height : Hgt

Angle : Ang

Vertical separation

(height between two points ): Hgt + Hgt2

Measureddistance/ Distance: 10-500meters/11-550yards/33-999feet

angle range (999 feet: 304.5 meters/333 yards)

Angle:

±89°

Distance- Act 0.5 meter/yard, 1.0 foot ( ＜100 meters/yards/feet)

Angle

(Linear distance)

1.0 meter/yard, 1.0 foot ( ≧ 100 meters/yards/feet)

Display Hor 0.2 meter/yard, 0.5 foot

( ＜ 100 meters/yards/feet)

Steps

(Horizontal dist.)

1.0 meter/yard, 1.0 foot ( ≧ 100 meters/yards/feet)

Hgt 0.2 meter/yard, 0.5 foot ( ＜ 100 meters/yards/feet)

(Height)

1.0 meter/yard, 1.0 foot ( ≧ 100 meters/yards/feet)

Ang

(Angle)

0.1°( ＜ 10°),1.0°( ≧ 10°)

Linear distance

0.5 meter/yard, 1.0 foot

Horizontal dist.

0.2 meter/yard, 0.5 foot

Height 0.2 meter/yard, 0.5 foot

Angle 0.1°

System First Target Priority Distance Display system

Internal

External

Laser

Class IECClass1M

Wavelength 870nm

Pulse duration 14 ns

Output 15W

Beam divergence Vertical：5°—8°,Horizontal：25°—36°

Operating humidity 80% RH (without dew condensation)

Laser Rangefinder

Nikon Callaway id TECH Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info