519656
24
Verklein
Vergroot
Pagina terug
1/133
Pagina verder
350 East Plumeria Drive
San Jose, CA 95134
USA
March 2013
202-11157-01
N300 Wireless ADSL2+ Modem
Router DGN2200v4
User Manual
2
N300 Wireless ADSL2+ Modem Router DGN2200v4
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it to register your product
at
https://my.netgear.com. You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website. For product updates and web
support, visit
http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at
http://support.netgear.com/general/contact/default.aspx.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change
without notice. ©2013 All rights reserved.
3
Contents
Chapter 1 Hardware Setup
Unpack Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Hardware Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Position Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
ADSL Microfilters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
One-Line ADSL Microfilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Two-Line ADSL Microfilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cable Your Modem Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Chapter 2 Access the Modem Router
Modem Router Setup Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Use Standard TCP/IP Properties for DHCP . . . . . . . . . . . . . . . . . . . . . .16
Gather ISP Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Wireless Devices and Security Settings. . . . . . . . . . . . . . . . . . . . . . . . .16
Types of Logins and Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
NETGEAR genie Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Use NETGEAR genie after Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Dashboard (Basic Home Screen). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Join Your Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Manual Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Wi-Fi Protected Setup (WPS) Method . . . . . . . . . . . . . . . . . . . . . . . . . .20
NETGEAR genie App and Mobile genie App . . . . . . . . . . . . . . . . . . . . . . .21
Chapter 3 NETGEAR genie Basic Settings
Internet Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Internet Setup Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Wireless Settings Screen Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Change WPA Security Option and Passphrase . . . . . . . . . . . . . . . . . . .30
Set Up a Guest Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
View Attached Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
4
N300 Wireless ADSL2+ Modem Router DGN2200v4
Chapter 4 NETGEAR genie Advanced Home
NETGEAR genie Advanced Home Screen . . . . . . . . . . . . . . . . . . . . . . . .34
Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
WPS Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
WAN Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
WAN Setup Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Default DMZ Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Change the MTU Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
LAN Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
LAN Setup Screen Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Specify DHCP Server Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Address Reservation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Quality of Service (QoS) Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
WMM QoS for Wireless Multimedia Applications . . . . . . . . . . . . . . . . . .43
Set Up QoS for Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Chapter 5 USB Storage
USB Drive Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Connect a USB Storage Device to the Modem Router . . . . . . . . . . . . . . .49
Safely Remove a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Access the USB Storage Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
File-Sharing Scenarios. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
View a USB Device Attached to the Modem Router . . . . . . . . . . . . . . . . .53
USB Storage Device Network and Access Settings. . . . . . . . . . . . . . . . . .54
Available Network Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Specify Approved USB Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Chapter 6 Security
Keyword Blocking of HTTP Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Set Up Firewall Rules to Control Network Access . . . . . . . . . . . . . . . . . . .60
Port Triggering to Open Incoming Ports. . . . . . . . . . . . . . . . . . . . . . . . . . .61
Port Forwarding to Permit External Host Communications . . . . . . . . . . . .62
How Port Forwarding Differs from Port Triggering . . . . . . . . . . . . . . . . . . .63
Set Up Port Forwarding to Local Servers. . . . . . . . . . . . . . . . . . . . . . . . . .63
Add a Custom Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Edit or Delete a Port Forwarding Entry. . . . . . . . . . . . . . . . . . . . . . . . . .65
Set Up Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Schedule When to Block the Internet. . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Security Event Email Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Chapter 7 Administration
Update the Modem Router Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
View Router Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Router Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Internet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
5
N300 Wireless ADSL2+ Modem Router DGN2200v4
Wireless Settings (2.4 GHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
View Logs of Web Access or Attempted Web Access . . . . . . . . . . . . . . . .75
Manage the Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Back Up Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Restore Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Erase the Current Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . .76
Change the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Password Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Chapter 8 Advanced Settings
Advanced Wireless Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Control the Wireless Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Set Up a Wireless Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
View or Change WPS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Set Up a Wireless Access List by MAC Address . . . . . . . . . . . . . . . . . .82
Wireless AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Wireless Distribution System (WDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Set Up the Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Set Up a Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Dynamic DNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Static Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Remote Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Universal Plug and Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Requirements for Entering IPv6 Addresses . . . . . . . . . . . . . . . . . . . . . .93
Auto Detect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
IPv6 Auto Config. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
IPv6 6to4 Tunnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
IPv6 Pass Through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
IPv6 Fixed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
IPv6 DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
IPv6 PPPoE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Traffic Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Chapter 9 Virtual Private Networking
Overview of VPN Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Client-to-Gateway VPN Tunnels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Gateway-to-Gateway VPN Tunnels . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Set Up a Client-to-Gateway VPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Add a Gateway-to-Gateway VPN Tunnel. . . . . . . . . . . . . . . . . . . . . . . . .107
Activate a VPN Tunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
View or Change the Status of a VPN Tunnel . . . . . . . . . . . . . . . . . . . . . .110
Deactivate a VPN Tunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Delete a VPN Tunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Auto Policy Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Add or Edit a VPN Auto Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Add or Edit a Manual VPN Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
6
N300 Wireless ADSL2+ Modem Router DGN2200v4
Chapter 10 Troubleshooting
Troubleshoot with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Power LED Is Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Power LED Is Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
LAN LED Is Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Cannot Log In to the Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Troubleshoot the Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . .122
ADSL Link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Internet LED Is Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Obtaining an Internet IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Troubleshoot PPPoE or PPPoA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Troubleshoot Internet Browsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
TCP/IP Network Not Responding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Test the LAN Path to Your Modem Router. . . . . . . . . . . . . . . . . . . . . .124
Test the Path from Your Computer to a Remote Device . . . . . . . . . . .125
Changes Not Saved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Incorrect Date or Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Appendix A Supplemental Information
Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
Appendix B Notification of Compliance
7
1
1. Hardware Setup
The N300 Wireless ADSL2+ Modem Router DGN2200v4 provides an easy and secure way to
set up a wireless home network with fast access to the Internet. You can connect the modem
router to a high-speed digital subscriber line (DSL) or behind a fiber cable modem using an
Ethernet WAN interface.
If you have not already set up your new modem router using the installation guide that comes in
the box, this chapter walks you through the hardware setup.
Chapter 2, Access the Modem
Router, explains how to set up your Internet connection.
This chapter contains the following sections:
Unpack Your Modem Router
Hardware Features
Position Your Modem Router
ADSL Microfilters
Cable Your Modem Router
For more information about the topics covered in this manual, visit the support website at
http://support.netgear.com.
If you want instructions about how to wall-mount your modem router, see Wall-Mount Your
Router at
http://support.netgear.com/app/answers/detail/a_id/18725.
Hardware Setup
8
N300 Wireless ADSL2+ Modem Router DGN2200v4
Unpack Your Modem Router
Your box should contain the following items:
ADSL
Phone
Line
Your package might contain more items.
The filter or splitter provided depends on
the region, and in some locations, a CD
is included.
N300 Modem Router
Ethernet cablePhone cable
Power adapter
Filter/splitter
Figure 1. Package contents
If any parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton and original packing materials in case you need to return the product for repair.
Hardware Features
Before you cable your modem router, take a moment to become familiar with the front panel,
back panel, and label. Pay particular attention to the LEDs on the front panel.
Hardware Setup
9
N300 Wireless ADSL2+ Modem Router DGN2200v4
Front Panel
The modem router front panel has the status LEDs and icons shown in the figure. The WiFi
and WPS icons are buttons.
WPS button
W
iFi On/Off button
Internet
DSL
Ethernet WAN
USB
LAN ports (1-4)
Power
Figure 2. Front panel LEDs and icons
The following table describes the LEDs, icons, and buttons on the front panel.
Table 1. Front panel icons for buttons and LEDs
Icon Description
WPS button Pressing this button lets you use Wi-Fi Protected Setup (WPS) to join the
network. (see Wi-Fi Protected Setup (WPS) Method on page 20).
Solid green. Wireless security has been enabled.
Blinking green. A
WPS-capable device is connecting to the device.
Off. WPS is not enabled.
WiFi On/Off button Pressing this button turns on and off the wireless radio in the modem router. By
default, WiFi is on.
Solid green. There
is WiFi connectivity.
Blinking green. Data is being transmitted or received over the WiFi link.
Off.
There is no WiFi connectivity. You can still plug an Ethernet cable into one of
the LAN ports to get wired connectivity. For more information about the use of
this button, see Advanced Wireless Settings on page 80.
Hardware Setup
10
N300 Wireless ADSL2+ Modem Router DGN2200v4
Internet Solid green. You have an Internet connection. If the connection timed out based
on the setting you entered in the Internet Setup screen, but the DSL connection
is still present, the LED stays green. If the Internet connection is dropped for any
other reason, the LED turns off.
Solid red. The
Internet (IP) connection failed. For troubleshooting information,
see Troubleshoot the Internet Connection on page 122.
Blinking green. Data is being transmitted over the DSL port.
Off. No Internet connection is detected or the device is in bridge mode (an
external device handles the ISP connection).
DSL
Solid green. You have a DSL connection. In technical terms, the DSL port is
synchronized with an ISP’s network-access device.
Blinking green.
The modem router is negotiating the best possible speed on the
DSL line.
Solid red.
The DSL connection could not be established.
Off.
The unit is off or there is no DSL link established.
WAN Network
Solid green. The modem router obtained a WAN IP address over Ethernet WAN
port 4 and the Internet connection is established.
Off. Ethernet W
AN port 4 is not being used as a WAN port, or the ISP has not
yet assigned an IP address over this port.
USB
Solid green. A USB device is connected and ready to use.
Blinking green.
A USB device is in use.
Off. No USB device connected, or someone clicked the Safely Remove
Hardware button, or an error has occurred with the device.
LAN (1-4)
Solid green. The LAN port has detected an Ethernet link with a device.
Off. No link is detected on this port.
Power
Solid green. Power is supplied to the modem router.
Solid red. POST (power-on self-test) failed or a device malfunction has
occurred.
Off. Power is not supplied to the modem router.
Blinking. When the Restore Factory Settings button is pressed for 6 seconds
(pressing it briefly resets the unit, the Power LED blinks red three times and then
turns green as the modem router resets to the factory defaults.
Table 1. Front panel icons for buttons and LEDs (continued)
Icon Description
Hardware Setup
11
N300 Wireless ADSL2+ Modem Router DGN2200v4
Back Panel
The back panel has the buttons and port connections as shown in the following figure.
ADSL port
Ethernet LAN ports
USB port
On/Off button
Power adapter input
Reset button
LAN port or WAN cable/fiber Internet port
Figure 3. Back panel connections and buttons
For information about resetting the modem router to its factory settings, see Factory Settings
on page 128.
Label
The label on the bottom of the modem router shows the preset login information, MAC
address, and serial number.
Wi-Fi network name
MAC address
Serial
and passwordnumber
Figure 4. Label on modem router bottom
Hardware Setup
12
N300 Wireless ADSL2+ Modem Router DGN2200v4
Position Your Modem Router
The modem router lets you access your network from virtually anywhere within the operating
range of your wireless network. However, the operating distance or range of your wireless
connection can vary significantly depending on the physical placement of your modem router.
For example, the thickness and number of walls the wireless signal passes through can limit
the range. For best results, place your modem router:
Near the center of the area where your computers and other devices operate and
preferably within line of sight to your wireless devices.
So it is accessible to an AC power outlet and near Ethernet cables for wired computers.
In an elevated location such as a high shelf, keeping the number of walls and ceilings
between the modem router and your other devices to a minimum.
Away from electrical devices that are potential sources of interference, such as ceiling
fans, home security systems, microwaves, computers, or a 2.4 GHz cordless phone and
its base.
Away from any large metal surfaces, such as a solid metal door or aluminum studs. Large
expanses of other materials such as glass, insulated walls, fish tanks, mirrors, brick, and
concrete can also affect your wireless signal.
ADSL Microfilters
If this is the first time you have cabled a modem router between a DSL phone line and your
computer or laptop, you might not be familiar with ADSL microfilters. If you are, you can skip
this section and proceed to
Cable Your Modem Router on page 14.
An ADSL microfilter is a small inline device that filters DSL interference out of standard phone
equipment that shares the same line with your DSL service. Every telephone device that
connects to a telephone line that provides DSL service needs an ADSL microfilter to filter out
the DSL interference. Examples of devices are telephones, fax machines, answering
machines, and caller ID displays. Not every phone line in your home necessarily carries DSL
service. That depends on the DSL service setup in your home.
Note: Often the ADSL microfilter is in the box with the modem router. If you
purchased the modem router in a country where a microfilter is not
included, you have to acquire the ADSL microfilter separately.
One-Line ADSL Microfilter
Plug the ADSL microfilter into the wall outlet and plug your phone equipment into the jack
labeled Phone. The modem router plugs directly into a separate DSL line. Plugging the
modem router into the phone jack blocks the Internet connection. If you do not have a
Hardware Setup
13
N300 Wireless ADSL2+ Modem Router DGN2200v4
separate DSL line for the modem router, the best thing to do is to use an ADSL microfilter
with a built-in splitter (see Two-Line ADSL Microfilter on page 13)
Plugs into DSL line
.
Figure 5. One-line ADSL microfilter
If you do not have a separate DSL line for the modem router, the second-best solution is to
get a separate splitter. To use a one-line filter with a separate splitter, insert the splitter into
the phone outlet, connect the one-line filter to the splitter, and connect the phone to the filter.
Two-Line ADSL Microfilter
Use an ADSL microfilter with a built-in splitter if you have a single wall outlet that provides
connectivity for both the modem router and your telephone equipment. Plug the ADSL
microfilter into the wall outlet, plug your phone equipment into the jack labeled Phone, and
plug the modem router into the jack labeled ADSL.
Plugs into the DSL line
Figure 6. Two-line ADSL microfilter with built-in splitter
Summary
One-line ADSL microfilter. Use with a phone or fax machine.
Splitter. Use with a one-line
ADSL microfilter to share an outlet with a phone and the
modem router.
T
wo-line ADSL microfilter with built-in splitter. Use to share an outlet with a phone
and the modem router.
Hardware Setup
14
N300 Wireless ADSL2+ Modem Router DGN2200v4
Cable Your Modem Router
You can use either a DSL or a cable/fiber Internet connection.
ADSL
Phone
Line
DSL Internet
Cable/fiber
or
Figure 7. Cable connections
CAUTION:
Incorrectly connecting a filter to your modem router blocks your DSL
connection.
For help with installation, see the installation guide that came in the package with your
product.
For information about how to access the modem router to view or change the settings, see
Chapter 2, Access the Modem Router.
15
2
2. Access the Modem Router
This chapter explains how to use NETGEAR genie to set up your modem router after you
complete cabling as described in the installation guide and in the previous chapter.
This chapter contains the following sections:
Modem Router Setup Preparation
Types of Logins and Access
NETGEAR genie Setup
Use NETGEAR genie after Installation
Upgrade the Firmware
Dashboard (Basic Home Screen)
Join Your Wireless Network
NETGEAR genie App and Mobile genie App
Access the Modem Router
16
N300 Wireless ADSL2+ Modem Router DGN2200v4
Modem Router Setup Preparation
You can set up your modem router with the NETGEAR genie automatically, or you can use
the genie menus and screens to set up your modem router manually. Before you start the
setup process, get your ISP information and make sure the computers and devices in the
network have the settings described here.
Use Standard TCP/IP Properties for DHCP
If you set up your computer to use a static IP address, you need to change the settings so
that it uses Dynamic Host Configuration Protocol (DHCP).
Gather ISP Information
If you have DSL broadband service, you might need the following information to set up your
modem router and to check that your Internet configuration is correct. Your Internet service
provider (ISP) should have provided you with all of the information needed to connect to the
Internet. If you cannot locate this information, ask your ISP to provide it. When your Internet
connection is working, you no longer need to launch the ISP’s login program on your
computer to access the Internet. When you start an Internet application, your modem router
automatically logs you in. Make sure that you have the following information:
The ISP configuration information for your DSL account
ISP login name and password
Fixed or static IP address settings (special deployment by ISP; this is rare)
Wireless Devices and Security Settings
Make sure that the wireless device or computer that you are using supports WPA or WPA2
wireless security, which is the wireless security supported by the modem router.
Types of Logins and Access
There are separate types of logins that have different purposes. It is important that you
understand the difference so that you know which login to use when.
Modem Router login logs you in to the modem router interface. For more information
about this login, see
Use NETGEAR genie after Installation on page 18.
ISP login logs you in to your Internet service. Your service provider has provided you with
this login information in a letter or some other way. If you cannot find this login
information, contact your service provider.
Wireless network key or password. Your modem router is preset with a unique wireless
network name (SSID) and password for wireless access. This information is on the label
on the bottom of your modem router.
Access the Modem Router
17
N300 Wireless ADSL2+ Modem Router DGN2200v4
NETGEAR genie Setup
NETGEAR genie runs on any device with a web browser. Installation and basic setup takes
about 15 minutes to complete.
To use NETGEAR genie to set up your modem router:
1. T
urn on the modem router by pressing the On/Off button.
2. Make sure that your computer or wireless device is connected to the modem router with an
Ethernet cable (wired) or wirelessly with the preset security settings listed on the bottom
label.
3. Launch your Internet browser
.
The first time you set up the Internet connection for your modem router, the browser
goes to http://www
.routerlogin.net, and the NETGEAR genie screen displays.
If you already used the NETGEAR genie, type http://www.routerlogin.net in the
address field for your browser to display the NETGEAR genie screen. See Use
NETGEAR genie after Installation on page 18.
4. Follow the onscreen instructions to complete NETGEAR genie setup.
NETGEAR genie guides you through connecting the modem router to the Internet.
If the browser cannot display the web page:
Make sure that the computer is connected to one of the four LAN Ethernet ports or
wirelessly to the modem router.
Make sure that the modem router has full power
, and that its WiFi LED is lit.
T
o make sure that the browser does not cache the previous page, close and reopen the
browser.
Browse to http://www
.routerlogin.net.
If the computer is set to a static or fixed IP address (this is uncommon), change it to
obtain an IP address automatically from the modem router.
Access the Modem Router
18
N300 Wireless ADSL2+ Modem Router DGN2200v4
If the modem router does not connect to the Internet:
1. Review your settings to be sure that you have selected the correct options and typed
everything correctly.
2. Contact your ISP to verify that you have the correct configuration information.
3. Read Chapter 10, Troubleshooting. If problems persist, register your NETGEAR product and
contact NETGEAR technical support.
Use NETGEAR genie after Installation
When you first set up your modem router, NETGEAR genie automatically starts when you
launch an Internet browser on a computer that is connected to the modem router. If you want
to view or change settings for the modem router, you can use genie again.
1. Launch your browser from a computer or wireless device that is connected to the
modem router.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
The login window displays.
3. Enter admin for the modem router user name and password for the modem router
password, both in lowercase letters.
Note: The modem router user name and password are different from the user
name and password for logging in to your Internet connection. For more
information, see
Types of Logins and Access on page 16.
Upgrade the Firmware
When you set up your modem router and are connected to the Internet, the modem router
automatically checks for you to see if newer firmware is available. If it is, a message is
displayed on the top of the screen. For more information, see
Update the Modem Router
Firmware on page 71.
Click the message when it shows up, and click Yes to upgrade the modem router with the
latest firmware. After the upgrade, the modem router restarts.
CAUTION:
Do not try to go online, turn off the modem router, shut down the computer,
or do anything else to the modem router until the modem router finishes
restarting and the Power LED has stopped blinking for several seconds.
Access the Modem Router
19
N300 Wireless ADSL2+ Modem Router DGN2200v4
Dashboard (Basic Home Screen)
The modem router Basic Home screen has a dashboard that lets you see the status of your
Internet connection and network at a glance. You can click any of the six sections of the
dashboard to view and change the settings. The left column has menus. You can use the
Advanced tab to access more menus and screens.
Menus
(Click the
Advanced
tab to view
more)
Language
Help
Dashboard
(Click to
view details)
Figure 8. Basic Home screen with dashboard, language, and online help
Home. This dashboard screen displays when you log in to the modem router.
Internet. Set, update, and check the ISP settings of your modem router.
W
ireless. View or change the wireless settings for your modem router.
Attached Devices. V
iew the devices connected to your network.
Parental Controls. Download and set up parental controls to prevent objectionable
content from reaching your computers.
ReadySHARE. If you connected a USB storage device to the modem router, then it is
displayed here.
Guest Network. Set up a guest network to allow visitors to use your modem router’
s
Internet connection.
Advanced tab. Set the modem router up for unique situations such as when remote
access by IP or by domain name from the Internet is needed. See Chapter 8, Advanced
Settings. You need a solid understanding of networking to use this tab.
Help & Support. Go to the NETGEAR support site to get information, help, and product
documentation.
These links work once you have an Internet connection.
Access the Modem Router
20
N300 Wireless ADSL2+ Modem Router DGN2200v4
Join Your Wireless Network
You can use the manual or the WPS method to join your wireless network. For instructions
about how to set up a guest network, see Set Up a Guest Network on page 31.
Manual Method
With the manual method, choose the network that you want and type its password to
connect.
To connect manually:
1. On your computer or wireless device, open the software that manages your wireless
connections.
This software scans for all wireless networks in your area.
2. Look for your network and select it.
The unique WiFi network name (SSID) and password are on the modem router label. If
you changed these settings, look for the network name that you used.
3. Enter the modem router password and click Connect.
Wi-Fi Protected Setup (WPS) Method
Wi-Fi Protected Setup (WPS) lets you connect to a secure WiFi network without typing its
password. Instead, press a button or enter a PIN. NETGEAR calls WPS Push 'N' Connect.
Some older WiFi equipment is not compatible with WPS. WPS works only with WPA2 or WPA
wireless security.
To use WPS to join the wireless network:
1. Press the WPS button on the modem router front panel
.
2. Within 2 minutes, press the WPS button on your wireless device, or follow the WPS
instructions that came with the device.
The WPS process automatically sets up your wireless computer with the network
password and connects you to the wireless network.
Access the Modem Router
21
N300 Wireless ADSL2+ Modem Router DGN2200v4
NETGEAR genie App and Mobile genie App
The genie app is the easy dashboard for managing, monitoring, and repairing your home
network. See the NETGEAR genie App User Manual for details about the genie apps.
Menu
Language
Support
Dashboard
(Click to
view
details)
Retrieve wireless password
About genie
Figure 9. genie app dashboard
The genie app can help you with the following:
Automatically repair common wireless network problems.
Have easy access to features like Live Parental Controls, guest access, Internet traf
fic
meter, speed test, and more.
The genie mobile app works on your iPhone, iPad, or Android phone:
Log in to the router
Information about
genie mobile app
Phone status
Search NETGEAR
support
and the connected
router
Figure 10. genie mobile app home screen
22
3
3. NETGEAR genie Basic Settings
This chapter contains the following sections:
Internet Setup
Parental Controls
Basic Wireless Settings
Set Up a Guest Network
View Attached Devices
For information about ReadySHARE USB storage, see Chapter 5, USB Storage.
NETGEAR genie Basic Settings
23
N300 Wireless ADSL2+ Modem Router DGN2200v4
Internet Setup
The Internet Setup screen is where you view or change basic ISP information.
Note: You can use the Setup Wizard to detect the Internet connection and
automatically set up the modem router. See Setup Wizard on
page 34.
To view or change the basic Internet setup:
1. From the Home screen, select Internet.
Scroll to
view more
settings
The fields that display in the Internet Setup screen depend on whether your Internet
connection requires a login.
Ye
s. Select the encapsulation method and enter the login name. If you want to
change the login time-out, enter a new value in minutes.
No. Enter the account and domain names, only if needed.
2. Enter the settings for the IP address and DNS server
.
The default settings usually work fine. If you have problems with your connection, check
the ISP settings.
3. Click Apply to save your settings.
4. Click T
est to test your Internet connection.
If the NETGEAR website does not display within 1 minute, see Chapter 10,
Troubleshooting.
NETGEAR genie Basic Settings
24
N300 Wireless ADSL2+ Modem Router DGN2200v4
Internet Setup Screen Fields
The following descriptions explain all of the possible fields in the Internet Setup screen. The
fields that display in this screen depend on whether tan ISP login is required.
Does Your Internet connection require a login? Answer either yes or no.
These fields display when no login is required:
Account Name (If required). Enter the account name provided by your ISP. This might
also be called the host name.
Domain Name (If required). Enter the domain name provided by your ISP.
These fields display when your ISP requires a login:
Internet Service Provider. The choices are PPPoE or PPPoA.
Login. The login name provided by your ISP. This login name is often an email address.
Password. The password that you use to log in to your ISP.
Service Name (if Required). If your ISP provided a service name, enter it here.
Connection Mode. Always On, Dial on Demand, or Manually Connect.
Idle Timeout (In minutes). If you want to change the login time-out, enter a new value in
minutes. This setting determines how long the modem router keeps the Internet
connection active after there is no Internet activity from the LAN. A value of 0 (zero)
means never log out.
Internet IP Address.
Get Dynamically from ISP. Your ISP uses DHCP to assign your IP address. Your ISP
automatically assigns these addresses.
Use Static IP Address. Enter the IP address, IP subnet mask, and the gateway IP
address that your ISP assigned. The gateway is the ISP’s modem router to which your
modem router will connect.
Domain Name Server (DNS) Address. The DNS server is used to look up site addresses
based on their names.
Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers. Your ISP
automatically assigns this address.
Use These DNS Servers. If you know that your ISP requires specific servers, select this
option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server
address is available, enter it also.
NAT (Network Address Translation). NAT allows computers on your home network to
share the modem router Internet connection. NAT is enabled by default because it is needed
in most situations. The following settings are available:
Enable
Disable
Disable Port Scan and DoS Protection
NETGEAR genie Basic Settings
25
N300 Wireless ADSL2+ Modem Router DGN2200v4
Router MAC Address. The Ethernet MAC address that the modem router uses on the
Internet port. Some ISPs register the MAC address of the network interface card in your
computer when your account is first opened. They accept traffic only from the MAC address
of that computer. This feature allows your modem router to use your computer’s MAC
address (also called cloning).
Use Default
Address. Use the default MAC address.
Use Computer MAC
Address. The modem router captures and uses the MAC address of
the computer that you are now using. You have to use the one computer that the ISP
allows.
Use This MAC
Address. Enter the MAC address that you want to use.
Parental Controls
The first time you select Parental Controls from the Basic Home screen, your browser goes
to the Live Parental Controls website. You can learn more about Live Parental Controls or
download the application.
Figure 11. Live Parental Controls website
To set up Live Parental Controls:
1. Select Parental Controls on the Dashboard screen.
2. Click either the W
indows Users or Mac Users button.
3. Follow the onscreen instructions to download and install the NETGEAR Live Parental
Controls Management Utility
.
NETGEAR genie Basic Settings
26
N300 Wireless ADSL2+ Modem Router DGN2200v4
After installation, Live Parental Controls automatically starts.
4. Click Next, read the note, and click Next again to proceed.
Because Live Parental Controls uses free OpenDNS accounts, you are prompted to log in
or create a free account.
5. Select the radio button that applies to you and click Next.
If you already have an OpenDNS account, leave the Ye
s radio button selected.
If you do not have an OpenDNS account, select the No radio button.
If you are creating an account, the following screen displays:
Fill in the fields and click Next.
NETGEAR genie Basic Settings
27
N300 Wireless ADSL2+ Modem Router DGN2200v4
After you log on or create your account, the filtering level screen displays:
6. Select the radio button for the filtering level that you want and click Next.
7. Click the Take me to the status screen button.
Parental controls are now set up for the modem router. The dashboard shows Parental
Controls as Enabled.
Basic Wireless Settings
The Wireless Settings screen lets you view or configure the wireless network setup.
The modem router comes with preset security. This means that the Wi-Fi network name
(SSID), network key (password), and security option (encryption protocol) are preset in the
factory
. You can find the preset SSID and password on the bottom of the unit.
Note: The preset SSID and password are uniquely generated for every
device to protect and maximize your wireless security.
NETGEAR genie Basic Settings
28
N300 Wireless ADSL2+ Modem Router DGN2200v4
NETGEAR recommends that you do not change your preset security settings. If you change
your preset security settings, make a note of the new settings and store it in a safe place
where you can easily find it.
If you use a wireless computer to change the wireless network name (SSID) or other wireless
security settings, you are disconnected when you click
Apply. To avoid this problem, use a
computer with a wired connection to access the modem router.
To view or change basic wireless settings:
1. Select Basic > W
ireless.
The screen sections, settings, and procedures are explained in the following sections.
2. Make any changes that are needed.
3. Click Appl.
Your settings are saved.
If you were connected wirelessly to the modem router and you changed the SSID or
wireless security
, you are disconnected from the network.
4. Set up and test your wireless devices and computers to make sure that they can connect
wirelessly. If they do not, check the following:
Is your wireless device or computer connected to your network or another wireless
network in your area? Some wireless devices automatically connect to the first open
network (without wireless security) that they discover
.
Does your wireless device or computer show up on the
Attached Devices screen? If it
does, it is connected to the network.
If you are not sure what the network name (SSID) or password is, look on the label on
the bottom of your modem router.
NETGEAR genie Basic Settings
29
N300 Wireless ADSL2+ Modem Router DGN2200v4
Wireless Settings Screen Fields
You can use this screen to view or change the wireless network settings and the security
option.
Wireless Network
Enable SSID Broadcast. This setting allows the modem router to broadcast its SSID so
wireless stations can see this wireless name (SSID) in their scanned network lists. This
check box is selected by default. To turn off the SSID broadcast, clear this check box, and
click Apply.
Enable Wireless Isolation. If this check box is selected, computers or wireless devices that
join the network can use the Internet, but cannot access each other or access Ethernet
devices on the network.
Name (SSID). The SSID is also known as the wireless network name. Enter a 32-character
(maximum) name in this field. This field is case-sensitive. The default SSID is randomly
generated, and NETGEAR strongly recommends that you do not change this setting.
Region. The location where the modem router is used. Select from the countries in the list. In
the United States, the region is fixed to United States and is not changeable.
Channel. This setting is the wireless channel the gateway uses. Enter a value from 1 through
13. (For products in the North America market, only Channels 1 through 11 can be operated.)
Do not change the channel unless you experience interference (shown by lost connections or
slow data transfers). If this happens, experiment with different channels to see which is the
best.
When you use multiple access points, it is better if adjacent access points use different radio
frequency channels to reduce interference. The recommended channel spacing between
adjacent access points is 5 channels (for example, use Channels 1 and 6, or 6 and 11).
Mode. Up to 145 Mbps is the default setting, which allows 802.11n and 802.11g wireless
devices to join the network. The other settings are Up to 54 Mbps, and Up to 300 Mbps.
Security Options Settings
The Security Options section of the Wireless Settings screen lets you change the security
option and passphrase. NETGEAR recommends that you do not change these settings,
but this section explains how. Do not disable security.
Wireless Security Options
A security option is the type of security protocol applied to your wireless network. The
security protocol in force encrypts data transmissions and ensures that only trusted devices
receive authorization to connect to your network. Wi-Fi Protected Access (WPA) has several
options including pre-shared key (PSK) encryption.
This section presents an overview of the security options and provides guidance on when to
use which option. It is also possible to set up a guest network without wireless security.
NETGEAR does not recommend this.
NETGEAR genie Basic Settings
30
N300 Wireless ADSL2+ Modem Router DGN2200v4
WPA encryption is built into all hardware that has the Wi-Fi-certified seal. This seal means
that the product is authorized by the Wi-Fi Alliance (http://www.wi-fi.org/) because it complies
with the worldwide single standard for high-speed wireless local area networking.
WPA uses a passphrase for authentication and to generate the initial data encryption keys.
Then it dynamically varies the encryption key
. WPA-PSK uses Temporal Key Integrity
Protocol (TKIP) data encryption, implements most of the IEEE 802.11i standard, and works
with all wireless network interface cards, but not all wireless access points.
WPA2-PSK is stronger than WPA-PSK. It is advertised to be theoretically indecipherable due
to the greater degree of randomness in encryption keys that it generates. WP
A2-PSK gets
higher speed because it is implemented through hardware, while WPA-PSK is usually
implemented through software. WPA2-PSK uses a passphrase to authenticate and generate
the initial data encryption keys. Then it dynamically varies the encryption key.
WPS-PSK + WPA2-PSK Mixed Mode can provide broader support for all wireless clients.
WP
A2-PSK clients get higher speed and security, and WPA-PSK clients get decent speed
and security. For help with WPA settings on your wireless computer or device, see the
instructions that came with your product.
Change WPA Security Option and Passphrase
You can change the security settings for your modem router. If you do so, then write down the
new settings and store them in a secure place for future reference.
To change the WPA settings:
1. Select Basic > Wireless Settings.
2. Under Security Options, select the WP
A option you want.
3. In the Passphrase field that displays when you select a WPA security option, enter the
network key (password) that you want to use. It is a text string from 8 to 63 characters.
NETGEAR genie Basic Settings
31
N300 Wireless ADSL2+ Modem Router DGN2200v4
Set Up a Guest Network
Adding a guest network allows visitors at your home to use the Internet without giving them
your wireless security key.
To set up a guest network:
1. Select Basic > Guest Network.
2. Select any of the following wireless settings:
Enable Guest Network. When this check box is selected, the guest network is enabled,
and guests can connect to your network using the SSID of this profile.
Enable SSID Broadcast. If this check box is selected, the wireless access point
broadcasts its name (SSID) to all wireless stations. Stations with no SSID can adopt the
correct SSID for connections to this access point.
Allow guest to access My Local Network. If this check box is selected, anyone who
connects to this SSID has access to your local network, not just Internet access.
Enable Wireless Isolation. If this check box is selected, wireless computers or devices
that join the network can use the Internet but cannot access each other or access
Ethernet devices on the network.
3. Give the guest network a name.
The guest network name is case-sensitive and can be up to 32 characters. You then
manually configure the wireless devices in your network to use the guest network name
in addition to the main SSID.
4. Select a security option from the list.
The security options are described in Wireless Security Options on page 29.
5. Click Apply.
Your settings are saved.
NETGEAR genie Basic Settings
32
N300 Wireless ADSL2+ Modem Router DGN2200v4
View Attached Devices
Use the Attached Device screen to view all computers or devices that are currently
connected to your network.
To go to the Attached Devices screen:
From the Basic Home screen, select Attached Devices.
Wired devices are connected to the modem router with Ethernet cables. Wireless devices
have joined the wireless network.
# (number). The order in which the device joined the network.
IP Address.
The IP address that the modem router assigned to this device when it joined
the network. This number can change if a device is disconnected and rejoins the network.
Device Name. If the device name is known, it is shown here.
MAC Address.
The unique MAC address for each device does not change. The MAC
address is typically shown on the product label.
Click Refresh to update this screen.
33
4
4. NETGEAR genie Advanced Home
This chapter contains the following sections:
NETGEAR genie Advanced Home Screen
Setup Wizard
WPS Wizard
WAN Setup
LAN Setup
Quality of Service (QoS) Setup
Some selections on the Advanced Home screen are described in separate chapters:
USB Storage. See Chapter 5, USB Storage.
Security. See Chapter 6, Security.
Administration. See Chapter 7, Administration.
Advanced Setup. See Chapter 8, Advanced Settings.
Advanced VPN. See Chapter 9, Virtual Private Networking.
NETGEAR genie Advanced Home
34
N300 Wireless ADSL2+ Modem Router DGN2200v4
NETGEAR genie Advanced Home Screen
The genie Advanced Home dashboard presents status information. The content is the same
as what is on the Router Status screen available from the Administration menu. The genie
Advanced Home screen is shown in the following figure:
This screen is
also displayed
through the
Administration
menu.
Setup Wizard
You can use the Setup Wizard to detect your Internet settings and automatically set up your
modem router. The Setup Wizard is not the same as the genie screens that display the first
time you connect to your modem router to set it up.
To use the Setup Wizard:
1. Select Advanced > Setup W
izard.
2. Select either Yes or No, I want to configure the router myself.
If you select No, you are taken to the Internet Setup screen (see Internet Setup on
page 23).
3. Select Ye
s and select your location.
4. Click Next.
NETGEAR genie Advanced Home
35
N300 Wireless ADSL2+ Modem Router DGN2200v4
The Setup Wizard searches your Internet connection for servers and protocols to
determine your ISP configuration. The following screen displays:
WPS Wizard
The WPS Wizard helps you add a WPS-capable client device (a wireless device or
computer) to your network. On the client device, either press its WPS button or locate its
WPS PIN.
To use the WPS Wizard:
1. Select Advanced > WPS W
izard.
2. Click Next.
The following screen lets you select the method for adding the WPS client (a wireless
device or computer).
You can use either the push button or PIN method.
3. Select either Push Button or PIN Number.
T
o use the push button method, either click the WPS button on this screen, or press
the WPS button on the side of the modem router. Within 2 minutes, go to the wireless
client and press its WPS button to join the network without entering a password.
NETGEAR genie Advanced Home
36
N300 Wireless ADSL2+ Modem Router DGN2200v4
To use the PIN method, select the PIN Number radio button, enter the client security
PIN, and click Next.
Within 2 minutes, go to the client device and use its WPS software to join the network
without entering a password.
The modem router attempts to add the WPS-capable device. The WPS LED on the
front of the modem router blinks green. When the modem router establishes a WPS
connection, the LED is solid green, and the modem router WPS screen displays a
confirmation message.
WAN Setup
You can use the WAN Setup screen to specify the ADSL or Ethernet port setting for your
Internet connection, though by default the modem router automatically detects the Internet
port. The WAN Setup screen also lets you configure a DMZ (demilitarized zone) server,
change the maximum transmit unit (MTU) size, and enable the modem router to respond to a
ping on the WAN (Internet) port.
To view or change the WAN settings:
1. Select Advanced > Setup > W
AN Setup.
2. Specify the settings for your Internet connection.
The fields in this screen are described in the following section.
3. Click Apply.
NETGEAR genie Advanced Home
37
N300 Wireless ADSL2+ Modem Router DGN2200v4
WAN Setup Screen Fields
The following fields are available:
WAN Preference. By default this field is set to Auto-Detect so that the modem router
automatically detects if the Internet connection is through the ADSL port or the
WAN/Ethernet port 4. You can use this field to select Must use DSL WAN or Must use
Ethernet WAN.
Use port 4 as. By default, Auto-Detect is selected so that the modem router detects if
Ethernet port 4 is used as a LAN or WAN port. For example, if you connect a computer to
Ethernet port 4, then it works as a LAN port. You can select LAN or WAN if you do not
want to use the auto-detect setting.
Disable Port Scan and DoS Protection. DoS protection protects your LAN against
denial of service attacks such as Syn flood, Smurf Attack, Ping of Death, Teardrop Attack,
UDP Flood, ARP Attack, Spoofing ICMP, Null Scan, and many others. This should be
disabled only in special circumstances.
Default DMZ Server. This feature is sometimes helpful when you are playing online
games or videoconferencing. Be careful when using this feature because it makes the
firewall security less effective. See the following section,
Default DMZ Server.
Respond to Ping on Internet Port. If you want the modem router to respond to a ping
from the Internet, select this check box. Use this feature only as a diagnostic tool
because it allows your modem router to be discovered. Do not select this check box
unless you have a specific reason.
Disable IGMP Proxying. The IGPM proxying feature lets a LAN computer receive the
multicast traffic directed to it from the Internet. Selecting this check box prevents this from
occurring.
MTU Size (in bytes). The normal MTU (maximum transmit unit) value for most Ethernet
networks is 1500 bytes, or 1492 bytes for PPPoE connections. For some ISPs, you might
need to reduce the MTU. This is rarely required. You should change the setting in this
field only if you are sure that it is necessary for your ISP connection. See
Change the
MTU Size on page 38.
NAT Filtering. Network Address Translation (NAT) determines how the modem router
processes inbound traffic. Secured NAT provides a secured firewall to protect the
computers on the LAN from attacks from the Internet, but might prevent some Internet
games, point-to-point applications, or multimedia applications from functioning. Open
NAT provides a much less secured firewall, but allows almost all Internet applications to
function.
Disable SIP ALG. The Session Initiation Protocol (SIP) Application Level Gateway (ALG)
is enabled by default to optimize VoIP phone calls that use the SIP. Select the Disable
SIP ALG check box to disable the SIP ALG. Disabling the SIP ALG might be useful when
you are running certain applications.
NETGEAR genie Advanced Home
38
N300 Wireless ADSL2+ Modem Router DGN2200v4
Default DMZ Server
The default DMZ server feature is helpful when you are using some online games and
videoconferencing applications that are incompatible with Network Address Translation
(NAT). The modem router recognizes some of these applications and works correctly with
them, but other applications might not function well. In some cases, one local computer can
run the application correctly if that computers IP address is entered as the default DMZ
server.
WARNING!
DMZ servers pose a security risk. A computer designated as the
default DMZ server loses much of the protection of the firewall and
is exposed to exploits from the Internet. If compromised, the DMZ
server computer can be used to attack other computers on your
network.
The modem router discards traffic from the Internet that is not a response to one of your
computers or a service that you have set up in the Port Forwarding/Port Triggering screen.
Instead of discarding this traffic, you can have the modem router forward the traffic to one
computer on your network. This computer is called the default DMZ server.
To set up a default DMZ server:
1. Select Advanced > Setup > WAN Setup. screen.
2. Select the Default DMZ Server check box.
3. Type the IP address.
4. Click Apply.
Your changes are saved.
Change the MTU Size
The maximum transmission unit (MTU) is the largest data packet a network device transmits.
When one network device communicates across the Internet with another, the data packets
travel through many devices along the way. If a device in the data path has a lower MTU
setting than the other devices, the data packets are split or “fragmented” to accommodate the
device with the smallest MTU.
The best MTU setting for NETGEAR equipment is often just the default value. In some
situations, changing the value fixes one problem but causes another. Leave the MTU
unchanged unless one of these situations occurs:
You have problems connecting to your ISP or other Internet service, and the technical
support of either the ISP or NETGEAR recommends changing the MTU setting. These
web-based applications might require an MTU change:
- A secure website that does not open, or displays only part of a web page
NETGEAR genie Advanced Home
39
N300 Wireless ADSL2+ Modem Router DGN2200v4
- Yahoo email
- MSN portal
- America Online’
s DSL service
Y
ou use VPN and have severe performance problems.
Y
ou used a program to optimize MTU for performance reasons, and now you have
connectivity or performance problems.
Note: An incorrect MTU setting can cause Internet communication
problems. For example, you might not be able to access certain
websites, frames within websites, secure login pages, or FTP or
POP servers.
If you suspect an MTU problem, a common solution is to change the MTU to 1400. If you are
willing to experiment, you can gradually reduce the MTU from the maximum value of 1500
until the problem goes away
. The following table describes common MTU sizes and
applications.
Table 2. Common MTU sizes
MTU Application
1500 The largest Ethernet packet size. This setting is typical for connections that do not use
PPPoE or VPN, and is the default value for NETGEAR modem routers, adapters, and
switches.
1492 Used in PPPoE environments.
1472 Maximum size to use for pinging. (Larger packets are fragmented.)
1468 Used in some DHCP environments.
1460 Usable by AOL if you do not have large email attachments, for example.
1436 Used in PPTP environments or with VPN.
1400 Maximum size for AOL DSL.
576 Typical value to connect to dial-up ISPs.
To change the MTU size:
1. Select Advanced > Setup > W
AN Setup.
2. In the MTU Size field, enter a value from 64 to 1500.
3. Click Apply.
Your change is saved.
NETGEAR genie Advanced Home
40
N300 Wireless ADSL2+ Modem Router DGN2200v4
LAN Setup
The LAN Setup screen allows configuration of LAN IP services such as Dynamic Host
Configuration Protocol (DHCP) and Routing Information Protocol (RIP). The modem router is
shipped preconfigured to use private IP addresses on the LAN side and to act as a DHCP
server. The modem router’s default LAN IP configuration is:
LAN IP address. 192.168.0.1
Subnet mask. 255.255.255.0
These addresses are part of the designated private address range for use in private networks
and are suitable for most applications.
By default, the modem router acts as a DHCP server. The modem router assigns IP, DNS
server
, and default gateway addresses to all computers connected to the LAN. The assigned
default gateway address is the LAN address of the modem router. The modem router tests
each address before it is assigned to avoid duplicate addresses on the LAN. For most
applications, the default DHCP and TCP/IP settings of the modem router are satisfactory.
The modem router delivers the following parameters to any LAN device that requests DHCP:
IP address
Subnet mask
Gateway IP address (the modem router’
s LAN IP address)
Primary DNS server (if specified in the Internet Setup screen), otherwise, the modem
router’
s LAN IP address)
Secondary DNS server if you entered this in the Internet Setup screen
If you change the LAN IP address of the modem router while connected through the browser,
you are disconnected from the network.
To change the LAN settings:
1. Select Advanced > Setup > LAN Setup.
NETGEAR genie Advanced Home
41
N300 Wireless ADSL2+ Modem Router DGN2200v4
2. Specify the settings that you want to customize (see LAN Setup Screen Settings).
3. Click Apply.
Your changes are saved.
LAN Setup Screen Settings
The following settings are available.
Device Name. By default, this is DGN2200v4 (the modem router model). You can change
it to another name if you prefer.
LAN TCP/IP Setup
IP Address. The LAN IP address of the modem router.
IP Subnet Mask. The LAN subnet mask of the modem router. Combined with the IP
address, the IP subnet mask allows a device to know which other addresses are local to
it, and which addresses have to be reached through a gateway or modem router.
RIP Direction. Router Information Protocol (RIP) allows the modem router to exchange
routing information with other routers. This setting controls how the modem router sends
and receives RIP packets. Both is the default setting. With the Both or Out Only setting,
the modem router broadcasts its routing table periodically. With the Both or In Only
setting, the modem router incorporates the RIP information that it receives.
RIP Version. This setting controls the format and the broadcasting method of the RIP
packets that the modem router sends. It recognizes both formats when receiving. By
default, the RIP function is disabled.
- RIP-1 is universally supported. It is adequate for most networks, unless you have an
unusual network setup.
- RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in
RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting.
Use Router as a DHCP Server
Usually, this check box is selected so that the modem router functions as a Dynamic Host
Configuration Protocol (DHCP) server.
Starting IP Address. Specify the start of the range for the pool of IP addresses in the
same subnet as the modem router.
Ending IP Address. Specify the end of the range for the pool of IP addresses in the
same subnet as the modem router.
Address Reservation
When you specify a reserved IP address for a computer on the LAN, that computer receives
the same IP address each time it accesses the modem router’s DHCP server. Assign
reserved IP addresses to servers that require permanent IP settings. See
Address
Reservation on page 42.
NETGEAR genie Advanced Home
42
N300 Wireless ADSL2+ Modem Router DGN2200v4
Specify DHCP Server Settings
By default, the modem router is set up as a DHCP server. You can specify the range of
addresses that the modem router assigns. You can also use another device on your network
as the DHCP server, or specify the network settings of all of your computers.
To specify the pool of IP addresses that the modem router assigns:
1. Select Advanced > LAN Setup.
2. Make sure that the Use Router as a DHCP Server check box is selected.
3. Specify the range of IP addresses.
For example, using the default addressing scheme, define a range between 192.168.0.2
and 192.168.0.254, although you might want to save part of the range for devices with
fixed addresses.
In the Starting IP Address field, specify the start of the range for the pool of IP
addresses in the same subnet as the modem router.
In the Ending IP Address field, specify the end of the range for the pool of IP
addresses in the same subnet as the modem router.
4. Click Apply.
Your changes are saved.
To disable the DHCP Server feature in the modem router:
1. Select Advanced > LAN Setup.
2. Clear the Use Router as DHCP Server check box
3. Click Apply.
4. If no DHCP server is on your network, set your computers’ IP addresses manually so that
they can access the modem router.
Address Reservation
When you specify a reserved IP address for a computer on the LAN, that computer always
receives the same IP address each time it accesses the modem router’s DHCP server.
Reserved IP addresses should be assigned to computers or servers that require permanent
IP settings.
To reserve an IP address:
1. Select Advanced > Setup > LAN Setup.
2. In the Address Reservation section of the screen, click the Add button.
3. In the IP Address field, type the IP address to assign to the computer or server.
Choose an IP address from the modem router’s LAN subnet, such as 192.168.0.x.
4. Type the MAC address of the computer or server.
NETGEAR genie Advanced Home
43
N300 Wireless ADSL2+ Modem Router DGN2200v4
Tip: If the computer is already on your network, you can copy its MAC
address from the Attached Devices screen and paste it here.
5. Click Apply
.
The reserved address is entered into the table.
The reserved address is not assigned until the next time the computer contacts the
modem router’
s DHCP server. Reboot the computer, or access its IP configuration and
force a DHCP release and renew.
To edit or delete a reserved address entry, select the radio button next to the reserved
address you want to edit or delete.
Then click Edit or Delete.
Quality of Service (QoS) Setup
QoS is an advanced feature that can be used to prioritize some types of traffic ahead of
others. The modem router can provide QoS prioritization over the wireless link and on the
Internet connection.
WMM QoS for Wireless Multimedia Applications
The modem router supports Wi-Fi Multimedia Quality of Service (WMM QoS) to prioritize
wireless voice and video traffic over the wireless link. WMM QoS provides prioritization of
wireless data packets from different applications based on four access categories: voice,
video, best effort, and background. For an application to receive the benefits of WMM QoS,
both it and the client running that application have to have WMM enabled. Legacy
applications that do not support WMM and applications that do not require QoS, are assigned
to the best effort category, which receives a lower priority than voice and video. WMM QoS is
enabled by default.
To disable WMM QoS:
1. Select Advanced > Setup > QoS Setup.
2. Clear the Enable WMM check box
3. Click Apply.
NETGEAR genie Advanced Home
44
N300 Wireless ADSL2+ Modem Router DGN2200v4
Set Up QoS for Internet Access
You can give prioritized Internet access to the following types of traffic:
Specific applications
Specific online games
Individual Ethernet LAN ports of the modem router
A specific device by MAC address
To specify prioritization of traffic, create a policy for the type of traffic and add the policy to the
QoS Policy table in the QoS Setup screen. For convenience, the QoS Policy table lists many
common applications and online games that can benefit from QoS handling.
QoS for Applications and Online Gaming
To create a QoS policy for applications and online games:
1. Select Advanced > Setup > QoS Setup.
2. Select the T
urn Internet Access QoS On check box.
3. Click the Setup QoS Rule button.
The QoS Priority Rule list displays.
You can edit or delete a rule by selecting its radio button and clicking either the Edit or
Delete button. You can also delete all the rules by clicking the Delete All button.
NETGEAR genie Advanced Home
45
N300 Wireless ADSL2+ Modem Router DGN2200v4
4. To add a priority rule, scroll down to the bottom of the QoS Setup screen and click Add
Priority Rule.
5. In the QoS Policy for field, type the name of the application or game.
6. In the Priority Category list, select either Applications or Online Gaming.
A list of applications or games displays.
7. Select an existing item from the list, scroll and select Add a New
Application, or Add a
New Game, as applicable.
8. If prompted, in the Connection
Type list, select either TCP, UDP, or both (TCP/UDP). Specify
the port number or range of port numbers that the application or game uses.
9. From the Priority list, select the priority for Internet access for this traf
fic relative to other
applications and traffic. The options are Low, Normal, High, and Highest.
10. Click Apply
The rule is saved in the QoS Policy list.
The QoS Setup screen displays.
QoS for a Modem Router LAN Port
To create a QoS policy for a device connected to a LAN port:
1. Select Advanced > Setup > QoS Setup.
2. Select the T
urn Internet Access QoS On check box.
3. Click the Setup QoS Rule button.
4. Click the Add Priority Rule button.
5. From the Priority Category list, select Ethernet LAN Port.
NETGEAR genie Advanced Home
46
N300 Wireless ADSL2+ Modem Router DGN2200v4
6. From the QoS Policy for list, select the LAN port.
7. From the Priority list, select the priority for Internet access for this port’
s traffic relative to
other applications. The options are Low, Normal, High, and Highest.
8. Click Apply
The rule is saved in the QoS Policy list.
The QoS Setup screen displays.
9. In the QoS Setup screen, click Apply.
QoS for a MAC Address
To create a QoS policy for traffic from a specific MAC address:
1. Select Advanced > Setup > QoS Setup, and click the Setup QoS Rule button.
The QoS Setup screen displays.
2. Click Add Priority Rule.
3. From the Priority Category list, select MAC Address.
4. If the device to be prioritized appears in the MAC Device List, select its radio button.
The information from the MAC Device List populates the policy name, MAC Address, and
Device Name fields. If the device does not appear in the MAC Device List, click Refresh.
If it still does not appear
, fill in these fields manually.
5. From the Priority list, select the priority for Internet access for this device’
s traffic reelative to
other applications and traffic. The options are Low, Normal, High, and Highest.
6. Click Apply.
This rule is saved in the QoS Policy list.
The QoS Setup screen displays.
7. Select the T
urn Internet Access QoS On check box.
8. Click Apply.
NETGEAR genie Advanced Home
47
N300 Wireless ADSL2+ Modem Router DGN2200v4
Edit or Delete an Existing QoS Policy
To edit or delete a QoS policy:
1. Select Advanced > QoS Setup.
2. Select the radio button next to the QoS policy that you want to edit or delete, and do one of
the following:
Click Delete to remove the QoS policy.
Click Edit to edit the QoS policy. Follow the instructions in the preceding sections to
change the policy settings.
3. Click Apply.
Your changes are saved in the QoS Setup screen.
48
5
5. USB Storage
This chapter describes how to access and configure a USB storage drive attached to your
modem router. The USB port on the modem router can be used only to connect USB storage
devices like flash drives or hard drives. Do not connect computers, USB modems, CD drives, or
DVD drives to the modem router USB port.
This chapter contains the following sections:
USB Drive Requirements
Connect a USB Storage Device to the Modem Router
Safely Remove a USB Drive
Access the USB Storage Device
File-Sharing Scenarios
Available Network Folders
USB Storage Device Network and Access Settings
Specify Approved USB Devices
For more about ReadySHARE features, visit www.netgear.com/readyshare.
USB Storage
49
N300 Wireless ADSL2+ Modem Router DGN2200v4
USB Drive Requirements
The modem router works with 1.0 and 1.1 (USB Full Speed) and 2.0 (USB High Speed)
standards. The approximate USB bus speeds are shown in the following table. Actual bus
speeds can vary, depending on the CPU speed, memory, speed of the network, and other
variables.
Table 3. USB drive speeds
Bus Speed/Sec
USB 1.1 12 Mbits
USB 2.0 480 Mbits
The modem router works with most USB-compliant external flash and hard drives. For the
most up-to-date list of USB drives that the modem router supports, visit:
http://kbserver.netgear.com/readyshare
The modem router supports both read and write for FAT16, FAT32, NTFS, and Linux file
systems (EXT2).
Note: Some USB external hard drives and flash drives require you to load
the drivers onto the computer before the computer can access the
USB device. Such USB devices do not work with the modem router.
Connect a USB Storage Device to the Modem Router
ReadySHARE lets you access and share or a USB drive connected the modem router USB
port. If your USB device has special drivers, it is not compatible.
To connect a USB storage device:
1. Insert your USB storage device into the USB port on the rear panel of the modem
router.
2. If your USB device has a power supply, you must use it when you connect the USB device
to the modem router.
USB Storage
50
N300 Wireless ADSL2+ Modem Router DGN2200v4
It might take up to 2 minutes before the USB device is ready for sharing.
Safely Remove a USB Drive
If you want to physically disconnect a USB drive from the modem router USB port, first, log in
to the modem router and safely remove it.
To remove a USB disk drive safely:
1. Select USB Storage > Basic Settings.
2. Click the Safely Remove USB Device button.
This takes the drive offline.
3. Physically disconnect the USB drive.
Access the USB Storage Device
When you connect the USB device to the modem router USB port, it might take up to 2
minutes before it is ready for sharing. By default, the USB storage device is available to all
computers on your local area network (LAN).
To access the USB device from a Mac:
1. Select Go > Connect to Server.
2. Enter smb://readyshare as the server address.
3. Click Connect.
To access the USB device from Windows:
Use any of these methods to access the USB device:
Select Start > Run. Enter \\readyshare in the dialog box and click OK.
Open a browser and enter \\readyshare in the address bar.
Open My Network Places and enter \\readyshare in the address bar.
To map the USB device to a Windows network drive:
1. Visit www.netgear.com/readyshare.
2. In the ReadySHARE USB Storage Access pane, click PC Utility.
The readyshareconnect.exe file is downloaded to your computer.
USB Storage
51
N300 Wireless ADSL2+ Modem Router DGN2200v4
3. Launch readyshareconnect.exe.
4. Select the drive letter to map to the network folder.
5. (Optional) If you want to connect to the USB drive as a dif
ferent user, select the Connect
using different credentials check box.
a. T
ype the user name and password that you want to use.
b. Click OK.
6. Click Finish.
The USB drive is mapped to the drive letter that you specified.
To access the USB drive from a remote computer:
1. Launch a web browser
.
2. Connect using the modem router’
s Internet port IP address.
If you are using Dynamic DNS, you can type the DNS name, rather than the IP address.
Y
ou can view the modem router’s Internet IP address on the Basic Home screen (see
Dashboard (Basic Home Screen) on page 16).
To access the USB drive with FTP from a remote computer:
1. Make sure that the FTP check box is selected in the
Access Method section of the USB
Storage Advanced Settings screen (see USB Storage Device Network and Access
Settings on page 54).
2. Launch a web browser
.
3. T
ype ftp:// and the Internet port IP address in the address field of the browser.
For example, type ftp://10.1.65.4.
If you are using Dynamic DNS, you can type the DNS name rather than the IP address.
4. T
ype the account name and password for the account that has access rights to the USB
drive.
The user name (account name) for All – no password is guest.
The folders on the USB drive that your account has access to display. For example, you
could see: share/partition1/directory1.
You can read and copy files from the USB folder.
USB Storage
52
N300 Wireless ADSL2+ Modem Router DGN2200v4
File-Sharing Scenarios
You can share files on the USB drive for a wide variety of business and recreational
purposes. The files can be any Windows, Mac, or Linux file type including text, Word,
PowerPoint, Excel, MP3, pictures, and multimedia files. USB drive applications include:
Sharing multimedia with friends and family such as MP3 files, pictures, and other
multimedia with local and remote users.
Sharing resources on your network. You can store files in a central location so that you do
not have to power up a computer to perform local sharing. In addition, you can share files
between Macintosh, Linux, and Windows computers by using the USB drive as a
go-between across the systems.
Sharing files such as Word documents, PowerPoint presentations, and text files with
remote users.
A few common uses are described in the following sections.
Share Photos
You can create your own central storage location for photos and multimedia. This method
eliminates the need to log in to (and pay for) an external photo-sharing site.
To share files with your friends and family:
1. Insert your USB drive into the USB port on the modem router either directly or with a
USB cable.
Computers on your local area network (LAN) can automatically access this USB drive
using a web browser or Microsoft Networking.
2. If you want to specify read-only access or to allow access from the Internet, see USB
Storage Device Network and Access Settings on page 54.
Store Files in a Central Location for Printing
This scenario is for a family that has one high-quality color printer directly attached to a
computer, but not shared on the local area network (LAN). This family does not have a print
server.
One family member has photos on a Macintosh computer that she wants to print.
The photo-capable color printer is directly attached to a PC, but not shared on the
network.
The Mac and PC are not visible to each other on the network.
To print photos from a Mac on the printer attached to a PC:
1. On the Mac, access the USB drive by typing \\readyshare in the address field of a web
browser. Then copy the photos to the USB drive.
2. On the PC, use a web browser or Microsoft Networking to copy the files from the USB drive
to the PC. Then print the files.
USB Storage
53
N300 Wireless ADSL2+ Modem Router DGN2200v4
Share Large Files over the Internet
Sending files that are larger than 5 MB can pose a problem for many email systems. The
modem router allows you to share large files such as PowerPoint presentations or .zip files
over the Internet. FTP can be used to download shared files from the modem router.
Sharing files with a remote colleague involves the following considerations:
There are two user accounts: admin and guest. The password for admin is the same one
that you use to access the modem router. By default, it is password. The guest user
account has no password.
On the FTP site, the person receiving the files uses the guest user account and enters
the password. (FTP requires that you type something in the password field.)
Be sure to select the FTP (via Internet) check box in the USB Storage (Advanced
Settings) screen.
This option supports both downloading and uploading of files.
You can enable the HTTP (via Internet) option on the USB Storage (Advanced Settings)
screen to share large files. This option supports downloading files only.
View a USB Device Attached to the Modem Router
To view basic information about the USB storage device:
1. Select Basic > ReadySHARE.
By default, the Basic radio button is selected and the screen displays a USB storage
device if it is attached to the modem router USB port.
If you logged in to the modem router before you connected your USB device, you might
not see your USB device in this screen. If this happens, log out and then log back in.
2. (Optional) To view the files and folders on the USB device, click the network device name or
the share name.
3. (Optional)
To view more detail or to change the USB device settings, click Edit.
The USB Storage (Advanced Settings) screen displays. See USB Storage Device
Network and Access Settings on page 54.
USB Storage
54
N300 Wireless ADSL2+ Modem Router DGN2200v4
USB Storage Device Network and Access Settings
You can set up the device name, workgroups, and network folders for your USB device.
To view or change the USB storage advanced settings:
1. Select Advanced > USB Storage > Advanced Settings.
2. Specify access to the USB storage device.
Network Device Name.
The default is readyshare. This is the name used to access
the USB device connected to the modem router.
W
orkgroup. If you are using a Windows workgroup rather than a domain, the
workgroup name is displayed here. The name works only in an operating system that
supports NetBIOS, such as Microsoft Windows.
Access Method. Select the check boxes for the access methods that you want.
- Network Neighborhood/MacShare. Enabled by default.
- HTTP. Enabled by default.
You can type
http://readyshare.routerlogin.net/shares to access the USB drive.
- HTTP (via Internet. Disabled by default. If you enable this setting, remote users
can type http://<public IP address/shares> (for example, http://1.1.10.102/shares)
or a URL domain name to access the USB drive over the Internet.
This feature
supports file uploading only.
- FTP. Disabled by default.
- FTP (via Internet). Disabled by default. If you select this feature, remote users
can access the USB drive through FTP over the Internet.
This setting supports
both downloading and uploading of files.
3. If you changed the settings, click Apply.
Your changes are saved.
USB Storage
55
N300 Wireless ADSL2+ Modem Router DGN2200v4
Available Network Folders
You can view or change the network folders on the USB storage device.
To view network folders:
1. Select Advanced > USB Storage > Advanced Settings.
2. Scroll down to the Available Networks Folder section of the screen.
Share Name. If only one device is connected, the default share name is
USB_Storage. (Some router models have more than one USB port.)
You can click the name, or you can type it in the address field of your web browser. If
Not Shared is shown, the default share has been deleted, and no other share for the
root folder exists. Click the link to change this setting.
Read Access
and Write Access. Shows the permissions and access controls on the
network folder: All - no password (the default) allows all users to access the network
folder. The password for admin is the same one that you use to log in to the modem
router.
Folder Name. Full path of the network folder
.
V
olume Name. Volume name from the storage device (either USB drive or HDD).
T
otal Space and Free Space. Shows the current utilization of the storage device.
To add a network folder:
1. Select Advanced > ReadySHARE.
2. Click Edit.
USB Storage
56
N300 Wireless ADSL2+ Modem Router DGN2200v4
3. To add a folder, click Create Network Folder.
If the Add a Network Folder screen does not display, your web browser might be blocking
pop-ups. If it is, then change the browser settings to allow pop-ups.
4. In the Folder field, browse and select the folder.
5. Fill in the Share Name field.
6. In the Read
Access list and the Write Access list, select the setting that you want.
The user name (account name) for All – no password is guest. The password for admin is
the same one that is used to log in to the modem router. By default, it is password.
7. Click Apply.
The folder is added on the USB device.
To edit a network folder:
1. Select Advanced > ReadySHARE.
2. Click the Edit button.
The Edit Network Folder screen displays the same settings shown in the Add a Network
Folder screen.
3. Change the settings in the fields as needed.
4. Click Apply.
Your changes are saved.
USB Storage
57
N300 Wireless ADSL2+ Modem Router DGN2200v4
Specify Approved USB Devices
For more security, you can set up the modem router to share only approved USB devices.
To set up approved USB devices:
1. Select Advanced >
Advanced Setup > USB Settings.
2. Click the Approved Devices button.
This screen shows the approved USB devices and the available USB devices. You can
remove or add approved USB devices.
3. In the Available USB Devices list, select the drive that you want to approve.
4. Click Add.
5. Select the Allow only approved devices check box.
6. Click Apply
.
Your change takes effect.
If you want to work with another USB device, first click the Safely Remove USB Device
button for the currently connected USB device. Connect the other USB device, and repeat
this process.
58
6
6. Security
This chapter explains how to use the basic firewall features of the modem router to prevent
objectionable content from reaching the computers and devices on your network.
This chapter includes the following sections:
Keyword Blocking of HTTP Traffic
Set Up Firewall Rules to Control Network Access
Port Triggering to Open Incoming Ports
Port Forwarding to Permit External Host Communications
How Port Forwarding Differs from Port Triggering
Set Up Port Forwarding to Local Servers
Set Up Port Triggering
Schedule When to Block the Internet
Security Event Email Notifications
Security
59
N300 Wireless ADSL2+ Modem Router DGN2200v4
Keyword Blocking of HTTP Traffic
Use keyword blocking to prevent certain types of HTTP traffic from accessing your network.
The blocking can be always or according to a schedule.
To set up keyword blocking:
1. Select Advanced > Security > Block Sites.
2. Select one of the keyword blocking options:
Per Schedule.
Turn on keyword blocking according to the Schedule screen settings.
Always.
Turn on keyword blocking all the time, independent of the Schedule screen.
3. In the Keyword field, enter a keyword or domain, click Add Keyword, and click Apply.
The Keyword list supports up to 32 entries. Here are some sample entries:
Specify XXX to block http://www
.badstuff.com/xxx.html.
Specify .com if you want to allow only sites with domain suf
fixes such as .edu or .gov.
Enter a period (.) to block all Internet browsing access.
To delete a keyword or domain:
1. Select the keyword you want to delete from the list.
2. Click Delete Keyword.
3. Click Apply
.
Your changes are saved.
To specify a trusted computer:
You can exempt one trusted computer from blocking and logging. The computer you exempt
has to have a fixed IP address.
1. In the
Trusted IP Address field, enter the IP address.
2. Click Apply.
Your changes are saved.
Security
60
N300 Wireless ADSL2+ Modem Router DGN2200v4
Set Up Firewall Rules to Control Network Access
Your modem router has a firewall that blocks unauthorized access to your wireless network
and permits authorized inbound and outbound communications. Authorized communications
are established according to inbound and outbound rules. The firewall has the following two
default rules
Inbound. Block all access from outside except responses to requests from the LAN side.
Outbound.
Allow all access from the LAN side to the outside.
You can add rules to further restrict the outbound communications or more widely open the
inbound communications. Exceptions can be based on the service or application, source or
destination IP addresses, and time of day
. You can log traffic that matches or does not match
the rule and change the order of rule precedence.
Traffic attempting to pass through the firewall is subjected to the rules in the order shown in
the Rules table from the top (highest precedence) to the bottom. In some cases, the order of
precedence determines which communications are allowed into or out of the network.
To set up firewall rules:
1. Select Advanced > Security > Firewall Rules.
2. You can add, edit, or delete a rule.
T
o add an outbound rule, click Add under Outbound Services.
T
o edit or delete a rule, select its button on the left side and click Edit or Delete.
3. (Optional) Change the order of precedence:
a. Select the button on the left side of the rule and click Move.
b. At the prompt, enter the number of the new position and click OK.
4. (Optional)
To open or close instant messaging, select one of the following radio buttons:
Close IM Ports. Disables instant messaging traf
fic.
Open IM Ports. Enables instant messaging traf
fic. IM ports are open by default.
5. Click Apply
.
Your changes are saved.
Security
61
N300 Wireless ADSL2+ Modem Router DGN2200v4
Port Triggering to Open Incoming Ports
Some application servers (such as FTP and IRC servers) send replies to multiple port
numbers. Using the port triggering function of your modem router, you can tell the modem
router to open more incoming ports when a particular outgoing port originates a session.
An example is Internet Relay Chat (IRC). Your computer connects to an IRC server at
destination port 6667. The IRC server not only responds to your originating source port, but
also sends an “identify” message to your computer on port 113. Using port triggering, you can
tell the modem router, “When you initiate a session with destination port 6667, you have to
also allow incoming traffic on port 113 to reach the originating computer.” Using steps similar
to the preceding example, the following sequence shows the effects of the port triggering rule
you have defined:
1. You open an IRC client program to start a chat session on your computer.
2. Your IRC client composes a request message to an IRC server using a destination port
number of 6667, the standard port number for an IRC server process. Your computer then
sends this request message to your modem router.
3. Your modem router creates an entry in its internal session table describing this
communication session between your computer and the IRC server. Your modem router
stores the original information, performs Network Address Translation (NAT) on the source
address and port, and sends this request message through the Internet to the IRC server.
4. Noting your port triggering rule and having observed the destination port number of 6667,
your modem router creates an additional session entry to send any incoming port 113 traffic
to your computer.
5. The IRC server sends a return message to your modem router using the NAT-assigned
source port (for example, port 33333) as the destination port. The IRC server also sends an
“identify” message to your modem router with destination port 113.
6. Upon receiving the incoming message to destination port 33333, your modem router
checks its session table to determine whether there is an active session for port number
33333. Finding an active session, the modem router restores the original address
information replaced by NAT and sends this reply message to your computer.
7. Upon receiving the incoming message to destination port 113, your modem router checks
its session table and learns that there is an active session for port 113, associated with your
computer. The modem router replaces the message’s destination IP address with your
computers IP address and forwards the message to your computer.
8. When you finish your chat session, your modem router eventually senses a period of
inactivity in the communications. The modem router then removes the session information
from its session table, and incoming traffic is no longer accepted on port numbers 33333 or
113.
To configure port triggering, you need to know which inbound ports the application needs.
Also, you need to know the number of the outbound port that will trigger the opening of the
inbound ports. You can usually determine this information by contacting the publisher of the
application or the relevant user groups or news groups.
Only one computer at a time can use the triggered application.
Security
62
N300 Wireless ADSL2+ Modem Router DGN2200v4
Port Forwarding to Permit External Host
Communications
In both of the preceding examples, your computer initiates an application session with a
server computer on the Internet. However, you might need to allow a client computer on the
Internet to initiate a connection to a server computer on your network. Normally, your modem
router ignores any inbound traffic that is not a response to your own outbound traffic. You can
configure exceptions to this default rule by using the port forwarding feature.
A typical application of port forwarding can be shown by reversing the client-server
relationship from the previous web server example. In this case, a remote computers
browser needs to access a web server running on a computer in your local network. Using
port forwarding, you can tell the modem router, “When you receive incoming traffic on port 80
(the standard port number for a web server process), forward it to the local computer at
192.168.0.123.” The following sequence shows the effects of the port forwarding rule you
have defined:
1. The user of a remote computer opens a browser and requests a web page from
www.example.com, which resolves to the public IP address of your modem router. The
remote computer composes a web page request message with the following destination
information:
Destination address. The IP address of www.example.com, which is the address of your
modem router.
Destination port number. 80, which is the standard port number for a web server
process.
The remote computer then sends this request message through the Internet to your
modem router.
2. Your modem router receives the request message and looks in its rules table for any rules
covering the disposition of incoming port 80 traffic. Your port forwarding rule specifies that
incoming port 80 traffic should be forwarded to local IP address 192.168.0.123. Therefore,
your modem router modifies the destination information in the request message:
The destination address is replaced with 192.168.0.123.
Your modem router then sends this request message to your local network.
3. Your web server at 192.168.0.123 receives the request and composes a return message
with the requested web page data. Your web server then sends this reply message to your
modem router.
4. Your modem router performs Network Address Translation (NAT) on the source IP address,
and sends this request message through the Internet to the remote computer, which
displays the web page from www.example.com.
To configure port forwarding, you need to know which inbound ports the application needs.
You usually can determine this information by contacting the publisher of the application or
the relevant user groups or news groups.
Security
63
N300 Wireless ADSL2+ Modem Router DGN2200v4
How Port Forwarding Differs from Port Triggering
The following points summarize the differences between port forwarding and port triggering:
Port triggering can be used by any computer on your network, although only one
computer can use it at a time.
Port forwarding is configured for a single computer on your network.
With port triggering, the modem router does not need to know the computer
’s IP address
in advance. The IP address is captured automatically.
Port forwarding requires that you specify the computer
’s IP address during configuration,
and the IP address can never change.
Port triggering requires specific outbound traf
fic to open the inbound ports, and the
triggered ports are closed after a period of no activity.
Port forwarding is always active and does not need to be triggered.
Set Up Port Forwarding to Local Servers
The port forwarding feature lets you allow certain types of incoming traffic to reach servers on
your local network. For example, you might want to make a local web server, FTP server, or
game server visible and available to the Internet.
Use the Port Forwarding/Port Triggering screen to configure the modem router to forward
specific incoming protocols to computers on your local network. In addition to servers for
specific applications, you can also specify a default DMZ server to which all other incoming
protocols are forwarded.
Before you start, determine which type of service, application, or game you want to provide,
and the local IP address of the computer that will provide the service.
The server computer
has to always have the same IP address.
To ensure that your server computer always has the same IP address, use the reserved IP
address feature of your product. See Address Reservation on page 42.
To forward specific incoming protocols:
1. Select Advanced >
Advanced Setup > Port Forwarding/Port Triggering.
Security
64
N300 Wireless ADSL2+ Modem Router DGN2200v4
2. From the Service Name list, select the service or game that you will host on your network.
If the service does not appear in the list, see Add a Custom Service on page 64.
3. In the
Action list, select when you want to allow or block this port forwarding rule.
4. In the Server IP
Address field, enter IP address of your local computer that will receive the
inbound traffic covered by this rule.
5. In the W
AN Servers field, fill in the IP addresses covered by this rule.
6. In the Log list, select Never or Always to specify when to log packets covered by this rule.
7. Click Add.
The service appears in the list on the Port Forwarding screen.
Add a Custom Service
To define a service, game, or application that does not appear in the Service Name list, first
determine which port number or range of numbers the application uses. You can usually
determine this information by contacting the publisher of the application or user groups or
news groups. When you have the port number information, follow these steps.
To add a custom service:
1. Select Advanced >
Advanced Setup > Port Forwarding/Port Triggering.
2. Select the Port Forwarding radio button as the service type.
3. Click the Add Custom Service button.
4. In the Name field, enter a descriptive name.
5. In the Service
Type list, select the protocol. If you are unsure, select TCP/UDP.
6. In the External and Internal Starting Port fields, enter the beginning port number
.
If the service uses only one port, enter the port number in the Ending Port field.
If the service uses a range of ports, enter the end port number in the Ending Port field.
7. In the Internal IP
Address field, enter the IP address of your local computer that will provide
this service.
8. Click Apply.
The service appears in the list in the Port Forwarding/Port Triggering screen.
Security
65
N300 Wireless ADSL2+ Modem Router DGN2200v4
Edit or Delete a Port Forwarding Entry
To edit or delete a port forwarding entry:
1. In the table, select the radio button next to the service name.
2. Click Edit Service or Delete Service.
Application Example: Make a Local Web Server Public
If you host a web server on your local network, you can use port forwarding to allow web
requests from anyone on the Internet to reach your web server.
To make a local web server public:
1. Assign your web server either a fixed IP address or a dynamic IP address using DHCP
address reservation.
In this example, your modem router always gives your web server an IP address of
192.168.0.33.
2. In the Port Forwarding/Port Triggering screen, configure the modem router to forward the
HTTP service to the local address of your web server at 192.168.0.33.
HTTP (port 80) is the standard protocol for web servers.
3. (Optional) Register a host name with a Dynamic DNS service, and configure your modem
router to use the name.
To access your web server from the Internet, a remote user has to know the IP address
that your ISP assigned. However, if you use a Dynamic DNS service, the remote user can
reach your server by a user-friendly Internet name, such as mynetgear.dyndns.org.
Set Up Port Triggering
Port triggering is a dynamic extension of port forwarding that is useful in these cases:
More than one local computer needs port forwarding for the same application (but not
simultaneously).
An application needs to open incoming ports that are different from the outgoing port.
When port triggering is enabled, the modem router monitors outbound traffic looking for a
specified outbound “trigger” port. When the modem router detects outbound traffic on that
port, it remembers the IP address of the local computer that sent the data. The modem router
then temporarily opens the specified incoming port or ports and forwards incoming traffic on
the triggered ports to the triggering computer.
Port forwarding creates a static mapping of a port number or range to a single local computer.
Port triggering can dynamically open ports to any computer that needs them and can close
the ports when they are no longer needed.
Security
66
N300 Wireless ADSL2+ Modem Router DGN2200v4
Note: If you use applications such as multiplayer gaming, peer-to-peer
connections, real-time communications such as instant messaging,
or remote assistance (a feature in Windows XP), you should also
enable Universal Plug and Play (UPnP).
To configure port triggering, you need to know which inbound ports the application needs,
and the number of the outbound port that will trigger the opening of the inbound ports.
You
can usually determine this information by contacting the publisher of the application or user
groups or news groups.
To enable port triggering:
1. Select Advanced > Port Forwarding/Port T
riggering.
2. Select the Port T
riggering radio button.
3. Clear the Disable Port Triggering check box.
Note: If the Disable Port Triggering check box is selected after you
configure port triggering, port triggering is disabled. However, any
port triggering configuration information you added to the modem
router is retained even though it is not used.
4. In the Port
Triggering Timeout field, enter a value up to 9999 minutes.
This value controls the inactivity timer for the designated inbound ports. The inbound
ports close when the inactivity time expires.
This is required because the modem router
cannot detect when the application has terminated.
Security
67
N300 Wireless ADSL2+ Modem Router DGN2200v4
To add a port triggering service:
1. On the Port Triggering screen, click Add Service.
2. In the Service Name field, type a descriptive service name.
3. In the Service User list, select Any or Single address and enter the IP address of one
computer
.
Any (the default), allows any computer on the Internet to use this service.
Single address restricts the service to a particular computer
.
4. Select the service type, either TCP or UDP or both (TCP/UDP). If you are not sure, select
TCP/UDP
.
5. In the
Triggering Port field, enter the number of the outbound traffic port that will cause the
inbound ports to be opened.
6. Enter the inbound connection port information in the Connection
Type, Starting Port, and
Ending Port fields.
7. Click Apply.
The service appears in the Port Triggering Portmap Table.
8. Make sure that you enable port triggering so that the service that you added will be used.
Security
68
N300 Wireless ADSL2+ Modem Router DGN2200v4
Schedule When to Block the Internet
You can specify the days and time that you want to block Internet access.
To schedule blocking:
1. Select Advanced > Security > Schedule.
2. Set up the schedule for blocking keywords and services.
Days to Block. Select days on which you want to apply blocking by selecting the
appropriate check boxes, or select Every Day to select the check boxes for all days.
T
ime of Day to Block. Select a start and end time in 24-hour format, or select All
Day for 24-hour blocking.
3. Select your time zone from the list. If you use daylight savings time, select the
Automatically adjust for daylight savings time check box.
4. Click Apply.
Your settings are saved.
Security
69
N300 Wireless ADSL2+ Modem Router DGN2200v4
Security Event Email Notifications
To receive logs and alerts by email, provide your email information in the E-mail screen, and
specify which alerts you want to receive and how often.
To set up email notifications:
1. Select Advanced > Security > E-mail.
2. Select the Turn Email Notification On check box.
3. In the
Your Outgoing Mail Server field, enter the name of your ISP’s outgoing (SMTP) mail
server (such as mail.myISP.com).
You might be able to find this information in the configuration screen of your email
program. If you leave this field blank, log and alert messages are not sent.
4. Enter the email address to which logs and alerts are sent in the Send to
This Email Address
field.
This email address is also used for the From address. If you leave this field blank, log and
alert messages are not sent.
5. If your outgoing email server requires authentication, select the My Mail Server requires
authentication check box. Fill in the User Name and Password fields for the outgoing email
server
.
6. (Optional) Select the Send Alerts
Immediately check box.
Email alerts are sent immediately when someone attempts to visit a blocked site.
7. (Optional) Fill in the fields in the Send logs according to this schedule section of the screen.
Logs are sent automatically. If the log fills up before the specified time, the log is emailed.
After the log is sent, the log is cleared from the modem router memory
. If the modem
router cannot email the log file, the log buffer might fill up. In this case, the modem router
overwrites the log and discards its contents.
8. Click Apply.
Your settings are saved.
70
7
7. Administration
Manage your network
This chapter describes the modem router settings for administering and maintaining your
modem router and home network. See
Remote Management on page 90 for information about
upgrading or checking the status of your modem router over the Internet. See Traffic Meter on
page 102 for information about monitoring Internet traffic.
This chapter includes the following sections:
Update the Modem Router Firmware
View Router Status
View Logs of Web Access or Attempted Web Access
Manage the Configuration File
Change the Password
Password Recovery
Administration
71
N300 Wireless ADSL2+ Modem Router DGN2200v4
Update the Modem Router Firmware
The modem router firmware (routing software) is stored in flash memory. You can update the
firmware from the Administration menu on the Advanced tab. You might see a message at
the top of the genie screens when new firmware is available for your product.
You can use the Check button on the Router Update screen to check and update to the latest
firmware for your product if new firmware is available.
To check for new firmware and update your modem router:
1. Select Advanced >
Administration > Router Update.
Click
Check
2. Click Check.
The modem router finds new firmware information if any is available.
3. Click Ye
s.
The modem router locates the firmware you downloaded (the file ends in .img) and
begins the update.
WARNING!
When uploading firmware to the modem router, do not interrupt
the web browser by closing the window, clicking a link, or loading
a new page. If the browser is interrupted, it could corrupt the
firmware.
When the upload is complete, your modem router restarts. The upgrade process typically
takes about 1 minute. Read the new firmware release notes to determine whether you
need to reconfigure the modem router after upgrading.
Administration
72
N300 Wireless ADSL2+ Modem Router DGN2200v4
View Router Status
To view modem router status and usage information:
Select Advanced Home or select Administration > Router Status.
Router Information
Hardware Version. The modem router model.
Firmware Version.
The version of the modem router firmware. It changes if you upgrade the
modem router firmware.
GUI Language Version. The localized language of the user interface.
LAN Port.
MAC Address.
The Media Access Control address. This is the unique physical address
used by the Ethernet (LAN) port of the modem router.
IP Address.
The IP address used by the Ethernet (LAN) port of the modem router. The
default is 192.168.0.1.
DHCP. Identifies whether the modem router’
s built-in DHCP server is active for devices
on the LAN.
Internet Port
MAC Address. The Media Access Control address, which is the unique physical address
used by the Internet (WAN) port of the modem router.
IP Address. The IP address used by the Internet (WAN) port of the modem router. If no
address is shown or the address is 0.0.0, the modem router cannot connect to the Internet.
Administration
73
N300 Wireless ADSL2+ Modem Router DGN2200v4
Connection. This shows if the modem router is using a fixed IP address on the WAN. If the
value is DHCP Client, the modem router obtains an IP address dynamically from the ISP.
IP Subnet Mask. The IP subnet mask used by the Internet (WAN) port of the modem router.
Domain Name Server.
The Domain Name Server addresses used by the modem router. A
Domain Name Server translates human-language URLs such as www.netgear.com into IP
addresses.
Show Statistics Button
To view statistics:
1. Select Advanced Home or select Administration > Router Status.
2. In the Internet Provider (W
AN) Setup pane, click the Show Statistics button.
The following information is displayed:
System Up Time.
The time elapsed since the modem router was last restarted.
Port.
The statistics for the WAN (Internet) and LAN (Ethernet) ports. For each port, the
screen displays:
Status. The link status of the port.
TxPkts.
The number of packets transmitted on this port since reset or manual clear.
RxPkts.
The number of packets received on this port since reset or manual clear.
Collisions.
The number of collisions on this port since reset or manual clear.
Tx B/s.
The current transmission (outbound) bandwidth used on the WAN and LAN ports.
Rx B/s.
The current reception (inbound) bandwidth used on the WAN and LAN ports.
Up T
ime. The time elapsed since this port acquired the link.
Poll Interval.
The interval at which the statistics are updated in this screen.
To change the polling frequency, enter a time in seconds in the Poll Interval field and click Set
Interval.
To stop the polling entirely, click Stop.
Administration
74
N300 Wireless ADSL2+ Modem Router DGN2200v4
Connection Status Button
To view the Internet connection status:
1. Select Advanced Home or select Administration > Router Status.
2. In the Internet Connection pane, click the Connection Status button.
The following information displays:
Connection T
ime. The time elapsed since the last connection to the Internet
through the DSL port.
Connection Status. On or Of
f.
Negotiation. On or Of
f.
Authentication. On or Of
f.
IP Address.
The IP address that is assigned to the modem router.
Subnet Mask.
The subnet mask that is assigned to the modem router.
3. (Optional) Connect or disconnect the modem router to the Internet.
Click Connect.
Click Disconnect
The Close Window button closes the Connection Status screen.
Wireless Settings (2.4 GHz)
The following settings are displayed:
Name (SSID).
The wireless network name (SSID) that the modem router uses.
Region.
The geographic region where the modem router is being used. It might be illegal to
use the wireless features of the modem router in some parts of the world.
Channel. The operating channel of the wireless port being used. The default channel is Auto.
When Auto is selected, the modem router finds the best operating channel available. If you
notice interference from nearby devices, you can select a different channel. Channels 1, 6,
and 11 do not interfere with each other.
Administration
75
N300 Wireless ADSL2+ Modem Router DGN2200v4
Mode. The wireless communication mode: Up to 54 Mbps, Up to 217 Mbps (default), and Up
to 1300 Mbps.
Wireless AP. Indicates whether the radio feature of the modem router is enabled. If this
feature is not enabled, the WiFi LED on the front panel is off.
Broadcast Name. Indicates whether the modem router is broadcasting its SSID.
Wireless Isolation. Wireless isolation prevents wireless clients from communicating with
each other when they join the wireless network.
Wi-Fi Protected Setup. Indicates whether WPS is configured for this network.
View Logs of Web Access or Attempted Web Access
The log is a detailed record of the websites you have accessed or attempted to access. Up to
256 entries are stored in the log. Log entries appear only when keyword blocking is enabled
and no log entries are made for the trusted user
.
To view logs:
Select Advanced >
Administration > Logs.
The log screen shows the following information:
Date and time.
The date and time the log entry was recorded.
Source IP.
The IP address of the initiating device for this log entry.
T
arget address. The name or IP address of the website or news group visited or to which
access was attempted.
Action. Whether the access was blocked or allowed.
To refresh the log screen, click the Refresh button.
To clear the log entries, click the Clear Log button.
To email the log immediately, click the Send Log button.
Administration
76
N300 Wireless ADSL2+ Modem Router DGN2200v4
Manage the Configuration File
The configuration settings of the modem router are stored within the modem router in a
configuration file. You can back up (save) this file to your computer, restore it, or reset it to the
factory default settings.
Back Up Settings
To back up the modem router’s configuration settings:
1. Select Advanced >
Administration > Backup Settings.
2. Click Backup Settings.
A copy of the current settings is saved.
3. Choose a location to store the .cfg file that is on a computer on your network.
Restore Configuration Settings
To restore configuration settings that you backed up:
1. Click the Browse button to find the cfg file.
2. Click the Restore button.
The files is uploaded to the modem router.
The modem router reboots.
WARNING!
Do not interrupt the reboot process.
Erase the Current Configuration Settings
You can use the Erase button erase the configuration and restore the factory default settings.
You might want to do this if you move the modem router to a different network or if you
changed the password and have forgotten what it is. (The default passwords are on the
product label).
Administration
77
N300 Wireless ADSL2+ Modem Router DGN2200v4
You can also use the Restore Factory Settings button on the back of the modem router to
erase the configuration and restore the factory settings. (See Factory Settings on page 128),.
To erase the configuration settings:
Click the Erase button.
The factory default settings are restored. The user name is admin, the password to
password, and the LAN IP address is 192.168.0.1. DHCP is enabled.
Change the Password
This feature let you change the default password that is used to log in to the modem router
with the user name admin. This is not the same as changing the password for wireless
access. The label on the bottom of your modem router shows your unique wireless network
name (SSID) and password for wireless access (see Label on page 11).
To set the password for the user name admin:
1. Select Advanced >
Administration > Set Password.
2. On the Set Password screen, type the old password, and type the new password twice.
3. If you want to be able to recover the password, select the Enable Password Recovery
check box.
4. Click Apply.
Your changes take effect.
Password Recovery
NETGEAR recommends that you enable password recovery if you change the password for
the user name admin. Then you can recover the password if it is forgotten. This recovery is
supported in Internet Explorer, Firefox, and Chrome browsers, but not in the Safari browser.
To set up password recovery:
1. Select the Enable Password Recovery check box.
2. Select two security questions, and provide answers to them.
3. Click Apply.
Your changes are saved.
Administration
78
N300 Wireless ADSL2+ Modem Router DGN2200v4
To recover your password:
1. In the address field of your browser, type www.routerlogin.net.
A login window displays.
2. Click Cancel.
If password recovery is enabled, you are prompted to answer two security questions.
3. Enter the saved answers to the security questions.
79
8
8. Advanced Settings
This chapter describes the advanced features of your modem router. Networking knowledge is
needed to implement some of these features.
Note: The Port Forwarding/Port Triggering screen can be accessed both
through the Advanced Setup menu and through the Firewall Rules
screen. For information about port forwarding and port triggering,
see Chapter 6, Security.
This chapter includes the following sections:
Advanced Wireless Settings
Wireless AP
Wireless Distribution System (WDS)
Dynamic DNS
Static Routes
Remote Management
Universal Plug and Play
IPv6
Traffic Meter
For information about the Approve USB feature, see Specify Approved USB Devices on
page 57.
Advanced Settings
80
N300 Wireless ADSL2+ Modem Router DGN2200v4
Advanced Wireless Settings
You can use this screen to turn on and off the wireless radio, to specify WPS settings, to use
AP mode, and to set up a wireless access list.
The Fragmentation Length, CTS/RTS Threshold, and Preamble Mode options in this screen
are reserved for wireless testing and advanced configuration only. Do not change these
settings unless you have a specific reason to do so.
Control the Wireless Radio
By default, the wireless radio is enabled so that you can connect wirelessly to the modem
router. You can turn the wireless radio on or off in the Advanced Wireless Settings screen or
by using the WiFi On/Off button on the modem router front panel.When the wireless radio is
off, you can still use an Ethernet cable for a LAN connection to the modem router
To turn the wireless radio on or off:
1. Select Advanced >
Advanced Setup > Wireless Settings.
By default, the Enable Wireless Router Radio check box is selected.
2. Select or clear the Enable W
ireless Router Radio check box.
If you clear this check box, this turns off the WiFi feature of the wireless modem router.
3. (Optional) Select the T
urn off wireless signal by schedule check box and fill in the fields
to specify the times when you do not need a wireless connection.
For instance, you could turn off the wireless signal for the weekend if you leave town.
4. Click Apply.
Your changes take effect.
Advanced Settings
81
N300 Wireless ADSL2+ Modem Router DGN2200v4
Set Up a Wireless Schedule
You can use this feature to turn off the wireless signal from your modem router at times when
you do not need a wireless connection. For example, you could turn it off for the weekend if
you leave town.
To configure and enable the wireless schedule:
1. Select Advanced >
Advanced Setup > Wireless Settings.
The Advanced Wireless Settings screen displays.
2. Click the Add a new period button.
The screen adjusts:
3. Use the menus, radio buttons, and check boxes to set up a period during which you want
the wireless signal to be turned off.
4. Click the Apply button.
The Advanced Wireless Settings screen displays.
5. Select the T
urn off wireless signal by schedule check box to activate the schedule.
6. Click the Apply button.
View or Change WPS Settings
To specify WPS Settings:
1. Select Advanced >
Advanced Setup > Wireless Settings.
The Routers PIN field displays the PIN that you use on a registrar (for example, from the
Network Explorer on a V
ista Windows computer) to configure the modem router’s
wireless settings through WPS.
2. (Optional) Select or clear the Disable Router
s PIN check box.
The PIN function might temporarily be disabled when the modem router detects
suspicious attempts to break into the modem router’
s wireless settings by using the
Advanced Settings
82
N300 Wireless ADSL2+ Modem Router DGN2200v4
modem router’s PIN through WPS. You can manually enable the PIN function by clearing
the Disable Routers PIN check box.
3. (Optional) Select or clear the Keep Existing Wireless Settings check box.
By default, the Keep Existing Wireless Settings check box is selected. NETGEAR
recommends that you leave this check box selected.
If you clear this check box, the next time a new wireless client uses WPS to connect to
the modem router, the modem router wireless settings change to an automatically
generated random SSID and security key
.
4. Click Apply.
Your changes are saved.
Set Up a Wireless Access List by MAC Address
You can set up a list of computers and wireless devices that are allowed to join the wireless
network. This list is based on the unique MAC address of each computer and device.
Each network device has a MAC address, which is a unique 12-character physical address,
containing the hexadecimal characters 0–9, a–f, or A–F only, and separated by colons (for
example, 00:09:AB:CD:EF:01). Typically, the MAC address is on the label of the wireless
card or network interface device. If you do not have access to the label, you can display the
MAC address using the network configuration utilities of the computer. You might also find the
MAC addresses in the Attached Devices screen.
To restrict access based on MAC addresses:
1. Select Advanced >
Advanced Setup > Wireless Settings.
2. Click the Setup Access
List button.
3. Click Add.
The Wireless Card Access Setup screen opens and displays a list of currently active
wireless cards and their Ethernet MAC addresses.
4. If the computer or device you want is in the
Available Wireless Cards list, select that radio
button; otherwise, type a name and the MAC address.
You can usually find the MAC address on the bottom of the wireless device.
Advanced Settings
83
N300 Wireless ADSL2+ Modem Router DGN2200v4
You can copy and paste the MAC addresses from the Attached Devices screen into the
MAC Address field of this screen. To do this, use each wireless computer to join the
wireless network. The computer should then appear in the Attached Devices screen.
5. Click Add.
The screen changes back to the list screen.
6. Add each computer or device you want to allow to connect wirelessly.
7. Select the Turn Access Control On check box.
8. Click Apply.
To edit a wireless device or delete it from the access list:
1. Select Advanced > Advanced Setup > Wireless Settings.
The Advanced Wireless Settings screen displays.
2. In the table, select the radio button next to the wireless device that you want to edit or
delete.
3. Do one of the following:
Click the Edit button.
The Edit Wireless Card screen displays.
a. Edit the address information.
b. Click the Accept button.
Click the Delete button.
The address is removed from the table.
Wireless AP
You can set up the modem router to run as an access point (AP) on the same local network
as another router.
To set up the modem router as an AP:
1. Use an Ethernet cable to connect the Ethernet WAN port (Ethernet port 4) of this
modem router to a LAN port in the other router.
2. Select Advanced > Advanced Setup > Wireless AP.
3. Select the Enable Access Point Mode check box.
4. Select the check box for the IP address setting that you want to use:
Get an IP address dynamically from the other router. The other router on the
network assigns an IP address to the modem router while the modem routerr is in AP
mode.
Fixed IP address (not recommended). Use this setting if you want to manually
assign a specific IP address to the modem router while it is in AP mode. Using this
option effectively requires advanced network experience.
Advanced Settings
84
N300 Wireless ADSL2+ Modem Router DGN2200v4
5. If the other router or gateway in your network also has wireless capability, NETGEAR
recommends that you use a different wireless channel.
6. Click Apply.
The IP address of the modem router changes and you are disconnected. To reconnect,
close and restart your web browser
, and type http://www.routerlogin.net.
Wireless Distribution System (WDS)
You can set up the modem router to be used as a wireless access point (AP). Doing this
enables the modem router to act as a wireless repeater. A wireless repeater connects to
another wireless modem router as a client where the network to which it connects becomes
the ISP service.
Wireless repeating is a type of Wireless Distribution System (WDS). A WDS allows a wireless
network to be expanded through multiple access points instead of using a wired backbone to
link them.
The following figure shows a wireless repeating scenario.
Repeater
Base station
access point
access point
Figure 12. Wireless repeating scenario
Note: To use the wireless repeating function, you need to select None as
the security option in the Wireless Setup screen and you cannot
select Auto Channel.
Wireless Base Station.
The modem router acts as the parent access point, that bridges
traffic to and from the child repeater access point. The base station also handles wireless and
Advanced Settings
85
N300 Wireless ADSL2+ Modem Router DGN2200v4
wired local computers. To configure this mode, you have to know the MAC addresses of the
child repeater access point. Often, the MAC address is on the product label.
Wireless Repeater. The modem router sends all traffic from its local wireless or wired
computers to a remote access point. To configure this mode, you have to know the MAC
address of the remote parent access point.
The modem router is always in dual-band concurrent mode, unless you turn off one radio. If
you enable the wireless repeater in either radio band, the wireless base station or wireless
repeater cannot be enabled in the other radio band. However
, if you enable the wireless base
station in either radio band and use the other radio band as a wireless modem router or
wireless base station, dual band concurrent mode is not affected.
For you to set up a wireless network with WDS, both access points have to meet the
following conditions:
Both access points have to use the same SSID, wireless channel, and encryption mode.
Both access points have to be on the same LAN IP subnet.
That is, all of the access point
LAN IP addresses are in the same network.
All LAN devices (wired and wireless computers) are configured to operate in the same
LAN network address range as the access points.
Set Up the Base Station
The wireless repeating function works only in hub and spoke mode. The units cannot be
daisy-chained. You have to know the wireless settings for both units. You have to know the
MAC address of the remote unit. First, set up the base station, and then set up the repeater.
To set up the base station:
1. Set up both units with the same wireless settings (SSID, mode, channel, and security).
The wireless security option has to be set to None or WEP
.
2. Select Advanced >
Advanced Setup > Wireless Repeating Function.
3. Select the Enable Wireless Repeating Function check box.
4. Select the W
ireless Base Station radio button.
Advanced Settings
86
N300 Wireless ADSL2+ Modem Router DGN2200v4
5. (Optional) Select the Disable Wireless Client Association check box to prevent wireless
clients from associating with the base station and allowing LAN client associations only.
You can leave the check box cleared if you prefer wireless clients to be able to associate
with the base stations.
6. In the Repeater MAC
Address 1 through 4 fields, enter the MAC addresses for the access
points that should function as repeaters.
If your modem router is the base station, it can function as the “parent” for up to four other
access points.
7. Click the Apply button.
Your changes are saved.
Set Up a Repeater
Use a wired Ethernet connection to set up the repeater unit to avoid conflicts with the wireless
connection to the base station.
If you are using the modem router as the base station with a non-NETGEAR router as the
repeater, you might need to change more configuration settings. In particular, you should
disable the DHCP server function on the access point that is the repeater.
To configure the modem router as a repeater:
1. Log in to the modem router that will be the repeater
.
2. Select Basic > W
ireless Settings and verify that the wireless settings match the base unit
exactly.
The wireless security option has to be set to WEP or None.
3. Select Advanced > W
ireless Repeating Function.
4. Select the Enable W
ireless Repeating Function check box.
5. Select the W
ireless Repeater radio button.
6. Fill in the Repeater IP Address field.
Advanced Settings
87
N300 Wireless ADSL2+ Modem Router DGN2200v4
This IP address has to be in the same subnet as the base station, but different from the
LAN IP address of the base station.
7. (Optional) Select the Disable
8. In the Base Station MAC
Address field,
9. Click Apply.
Your changes are saved.
10. V
erify connectivity across the LANs.
A computer on any wireless or wired LAN segment of the modem router can connect to
the Internet or share files and printers with any other computer or server connected to the
other access point.
Dynamic DNS
If your ISP assigned you a fixed IP address, you can register a domain name and link it to
your IP address by public DNS. However, most Internet accounts use dynamically assigned
IP addresses that can change frequently. In this case, you can use a commercial Dynamic
DNS service. This type of service lets you register your domain to their IP address and
forwards traffic directed at your domain to your frequently changing IP address.
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), the Dynamic
DNS service does not work because private addresses are not routed on the Internet.
Your modem router contains a client that can connect to the Dynamic DNS service provided
by DynDNS.org. First visit their website at http://www
.dyndns.org and obtain an account and
host name that you configure in the modem router. Then, whenever your ISP-assigned IP
address changes, your modem router automatically contacts the Dynamic DNS service
provider, logs in to your account, and registers your new IP address. If your host name is
hostname, for example, you can reach your modem router at http://hostname.dyndns.org.
To set up Dynamic DNS:
1. Select Advanced >
Advanced Setup > Dynamic DNS.
2. Register for an account with one of the Dynamic DNS service providers whose URLs are in
the Service Provider list.
For example, for DynDNS.org, select www
.dyndns.org.
3. Select the Use a Dynamic DNS Service check box.
Advanced Settings
88
N300 Wireless ADSL2+ Modem Router DGN2200v4
4. Select the URL of your Dynamic DNS service provider.
5. Type the host name (or domain name) that your Dynamic DNS service provider gave you.
6. Type the user name for your Dynamic DNS account.
This is the name that you use to log in to your account, not your host name.
7. Type the password (or key) for your Dynamic DNS account.
8. Click Apply.
Your changes are saved.
Static Routes
Static routes provide more routing information to your modem router. Typically, you do not
need to add static routes. You have to configure static routes only for unusual cases such as
multiple modem routers or multiple IP subnets on your network.
As an example of when a static route is needed, consider the following case:
Your primary Internet access is through a cable modem to an ISP.
You have an ISDN modem router on your home network for connecting to the company
where you are employed. This modem router’s address on your LAN is 192.168.0.100.
Your company’s network address is 134.177.0.0.
When you first configured your modem router, two implicit static routes were created. A
default route was created with your ISP as the gateway, and a second static route was
created to your local network for all 192.168.0.x addresses. With this configuration, if you
attempt to access a device on the 134.177.0.0 network, your modem router forwards your
request to the ISP. The ISP forwards your request to the company where you are employed,
and the request is likely to be denied by the company’s firewall.
In this case you have to define a static route, telling your modem router that 134.177.0.0
should be accessed through the ISDN modem router at 192.168.0.100. In this example:
The Destination IP Address and IP Subnet Mask fields specify that this static route
applies to all 134.177.x.x addresses.
The Gateway IP Address field specifies that all traffic for these addresses should be
forwarded to the ISDN modem router at 192.168.0.100.
A metric value of 1 works because the ISDN modem router is on the LAN.
Private is selected only as a precautionary security measure in case RIP is activated.
To set up a static route:
1. Select Advanced > Advanced Setup > Static Routes.
Advanced Settings
89
N300 Wireless ADSL2+ Modem Router DGN2200v4
2. Click Add.
3. In the Route Name field, type a name for this static route (for identification purposes only.)
4. Select the Private check box if you want to limit access to the LAN only
.
If Private is selected, the static route is not reported in RIP.
5. Select the Active check box to make this route ef
fective.
6. T
ype the destination IP address of the final destination.
7. T
ype the IP subnet mask for this destination. If the destination is a single host, type
255.255.255.255.
8. T
ype the gateway IP address, which has to be on the same LAN segment as the modem
router.
9. T
ype a number from 1 through 15 as the metric value.
This value represents the number of modem routers between your network and the
destination. Usually
, a setting of 2 or 3 works, but if this is a direct connection, set it to 1.
10. Click Apply
The static route is added.
To edit or delete a static route:
1. Select Advanced >
Advanced Setup > Static Routes.
The Static Routes screen displays.
2. In the table, select the radio button next to the route that you want to edit or delete.
3. Do one of the following:
Click the Edit button.
The Static Routes screen adjusts.
a. Edit the route information.
b. Click the Apply button.
Click the Delete button.
The route is removed from the table.
Advanced Settings
90
N300 Wireless ADSL2+ Modem Router DGN2200v4
Remote Management
The remote management feature lets you upgrade or check the status of your modem router
over the Internet.
Note: Be sure to change the modem router default login password to a
secure password. The ideal password contains no dictionary words
from any language and contains uppercase and lowercase letters,
numbers, and symbols. It can be up to 30 characters.
To set up remote management:
1. Select Advanced >
Advanced Setup > Remote Management.
2. Select the Turn Remote Management On check box.
3. Under
Allow Remote Access By, specify the external IP addresses to be allowed to access
the modem router’s remote management.
For enhanced security, restrict access to as few external IP addresses as practical.
T
o allow access from a single IP address on the Internet, select Only This Computer.
Enter the IP address that will be allowed access.
T
o allow access from a range of IP addresses on the Internet, select IP Address
Range. Enter a beginning and ending IP address to define the allowed range.
T
o specify IP addresses, select IP Address List and type in the allowed IP
addresses.
T
o allow access from any IP address on the Internet, select Everyone.
4. Specify the port number for accessing the web management interface.
Advanced Settings
91
N300 Wireless ADSL2+ Modem Router DGN2200v4
Normal web browser access uses the standard HTTP service port 80. For greater
security, enter a custom port number for the remote web management interface. Choose
a number from 1024 to 65535, but do not use the number of any common service port.
The default is 8080, which is a common alternate for HTTP.
5. Click Apply.
Your changes take effect.
6. When you access your modem router from the Internet, type your modem router’
s WAN IP
address into your browsers address or location field followed by a colon (:) and the custom
port number.
For example, if your external address is 134.177.0.123 and you use port number 8080,
enter http://134.177.0.123:8080 in your browser
.
Universal Plug and Play
Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers,
access the network and connect to other devices as needed. UPnP devices can
automatically discover the services from other registered UPnP devices on the network.
If you use applications such as multiplayer gaming, peer-to-peer connections, or real-time
communications such as instant messaging or remote assistance (a feature in Windows XP),
you should enable UPnP
.
To turn on Universal Plug and Play:
1. Select Advanced >
Advanced Setup > UPnP.
2. Select the Turn UPnP On check box.
By default, this check box is selected. UPnP for automatic device configuration
can be enabled or disabled. If the T
urn UPnP On check box is cleared, the modem
router does not allow any device to automatically control the resources, such as
port forwarding (mapping), of the modem router.
3. T
ype the advertisement period in minutes.
The advertisement period specifies how often the modem router broadcasts its
UPnP information. This value can range from 1 to 1440 minutes. The default period
is 30 minutes. Shorter durations ensure that control points have current device
status at the expense of additional network traffic. Longer durations can
Advanced Settings
92
N300 Wireless ADSL2+ Modem Router DGN2200v4
compromise the freshness of the device status, but can significantly reduce
network traffic.
4. Type the advertisement time to live in hops.
The time to live for the advertisement is measured in hops (steps) for each UPnP
packet sent. The time to live hop count is the number of steps a broadcast packet is
allowed to propagate for each UPnP advertisement before it disappears. The
number of hops can range from 1 to 255. The default value for the advertisement
time to live is 4 hops, which should be fine for most home networks. If you notice
that some devices are not being updated or reached correctly
, it might be
necessary to increase this value.
5. Click the
Apply button.
The UPnP Portmap Table displays the IP address of each UPnP device that is
accessing the modem router. The UPnP Portmap T
able also shows which ports are
open, what type of ports are open, and whether each open port is still active for
each IP address.
To refresh the information in the UPnP Portmap Table, click the Refresh button.
IPv6
You can use this feature to set up an IPv6 Internet connection type if genie does not detect it
automatically.
To set up an IPv6 Internet connection type:
1. Select Advanced >
Advanced Setup > IPv6.
2. In the Internet Connection Type list, select the IPv6 connection type.
Your Internet service provider (ISP) can provide this information.
If your ISP did not provide details, you can select IPv6 T
unnel.
If you are not sure, select Auto Detect so that the modem router detects the IPv6
type that is in use.
If your Internet connection does not use PPPoE, DHCP
, or fixed, but is IPv6, select
Auto Config.
For more detailed information about Internet connection types, see the following sections.
3. Click the Apply button.
Advanced Settings
93
N300 Wireless ADSL2+ Modem Router DGN2200v4
Your changes take effect.
Requirements for Entering IPv6 Addresses
IPv6 addresses are denoted by eight groups of hexadecimal quartets that are separated by
colons. Any four-digit group of zeroes within an IPv6 address can be reduced to a single zero
or altogether omitted.
The following errors invalidate an IPv6 address:
More than eight groups of hexadecimal quartets
More than four hexadecimal characters in a quartet
More than two colons in a row
Advanced Settings
94
N300 Wireless ADSL2+ Modem Router DGN2200v4
Auto Detect
To set up an IPv6 Internet connection through auto detection:
1. Select Advanced >
Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection
Type list, select Auto Detect.
The screen adjusts:
The modem router automatically detects the information in the following fields:
Connection T
ype. This field indicates the connection type that is detected.
Router
s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the modem router’s WAN (or Internet) interface. The number after the slash (/) is
the length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
Router
s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the modem router’s LAN interface. The number after the slash (/) is the length of
the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
3. Specify how the modem router assigns IPv6 addresses to the devices on your home
network (the LAN) by selecting one of the following radio buttons:
Use DHCP Server.
This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
Auto Config.
This is the default setting.
4. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the modem router’
s LAN interface.
If you do not specify an ID here, the modem router generates one automatically from its
MAC address.
5. Click the Apply button.
Advanced Settings
95
N300 Wireless ADSL2+ Modem Router DGN2200v4
IPv6 Auto Config
To set up an IPv6 Internet connection through auto configuration:
1. Select Advanced >
Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection
Type list, select Auto Config.
The screen adjusts:
The modem router automatically detects the information in the following fields:
Router
s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the modem router’s WAN (or Internet) interface. The number after the slash (/) is
the length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
Router
s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the modem router’s LAN interface. The number after the slash (/) is the length of
the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
3. (Optional) In the DHCP User Class (If Required) field, enter a host name.
Most people do not need to fill in this field, but if your ISP has given you a specific host
name, enter it here.
4. (Optional) In the Domain Name (If Required) field, enter a domain name.
You can type the domain name of your IPv6 ISP. (Do not enter the domain name for the
IPv4 ISP here.) For example, if your ISP’
s mail server is mail.xxx.yyy.zzz, you would type
xxx.yyy.zzz as the domain name. If your ISP provided a domain name, type it in this field.
(For example, Earthlink Cable might require a host name of home, and Comcast
sometimes supplies a domain name.)
5. Specify how the modem router assigns IPv6 addresses to the devices on your home
network (the LAN) by selecting one of the following radio buttons:
Advanced Settings
96
N300 Wireless ADSL2+ Modem Router DGN2200v4
Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
Auto Config.
This is the default setting.
6. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the modem router’
s LAN interface.
If you do not specify an ID here, the modem router generates one automatically from its
MAC address.
7. Click the Apply button.
IPv6 6to4 Tunnel
The remote relay router is the router to which your modem router creates the 6to4 tunnel.
Make sure that the IPv4 Internet connection is working before you apply the 6to4 tunnel
settings for the IPv6 connection.
To set up an IPv6 Internet connection by using a 6to4 tunnel:
1. Select Advanced >
Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection
Type list, select 6to4 Tunnel.
The screen adjusts:
The modem router automatically detects the information in the following fields:
Router
s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the modem router’s WAN (or Internet) interface. The number after the slash (/) is
the length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
Router
s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the modem router’s LAN interface. The number after the slash (/) is the length of
the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
Advanced Settings
97
N300 Wireless ADSL2+ Modem Router DGN2200v4
3. Configure the remote 6to4 relay modem router settings by selecting one of the following
buttons:
Auto. Your modem router uses any remote relay router that is available on the
Internet. This is the default setting.
Static IP Address. Enter the static IPv4 address of the remote relay router. This
address is usually provided by your IPv6 ISP.
4. Specify how the modem router assigns IPv6 addresses to the devices on your home
network (the LAN) by selecting one of the following radio buttons:
Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
Auto Config. This is the default setting.
5. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the modem router’s LAN interface.
If you do not specify an ID here, the modem router generates one automatically from its
MAC address.
6. Click the Apply button.
IPv6 Pass Through
In pass-through mode, the modem router works as a Layer 2 Ethernet switch with two ports
(LAN and WAN Ethernet ports) for IPv6 packets. The modem router does not process any
IPv6 header packets.
To set up a pass-through IPv6 Internet connection:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection Type list, select Pass Through.
The screen adjusts, but no additional fields display.
3. Click the Apply button.
IPv6 Fixed
To set up a pass-through IPv6 Internet connection:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. Select Fixed from the menu.
Advanced Settings
98
N300 Wireless ADSL2+ Modem Router DGN2200v4
The screen adjusts:
3. Configure the fixed IPv6 addresses for the WAN connection.
The following fields are included in this screen:
IPv6 Address/Prefix
Length. The IPv6 address and prefix length of the modem
router WAN interface.
Default IPv6 Gateway.
The IPv6 address of the default IPv6 gateway, which is
supposed to be on the modem router’s WAN interface.
Primary DNS Server.
The primary DNS server that resolves IPv6 domain name
records for the modem router.
Secondary DNS Server.
The secondary DNS server that resolves IPv6 domain
name records for the modem router.
Note: If you do not specify the DNS servers, the modem router uses the DNS
servers that are configured for the IPv4 Internet connection on the Internet
Setup screen. (See Internet Setup on page 23.)
4. Specify how the modem router assigns IPv6 addresses to the devices on your home
network (the LAN) by selecting one of the following radio buttons:
Use DHCP Server.
This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
Auto Config.
This is the default setting.
5. In the IPv6
Address/Prefix Length fields, specify the static IPv6 address and prefix length of
the modem router’s LAN interface.
If you do not specify an ID here, the modem router generates one automatically from its
MAC address.
6. Click the Apply button.
Advanced Settings
99
N300 Wireless ADSL2+ Modem Router DGN2200v4
IPv6 DHCP
To set up an IPv6 Internet connection with a DHCP server:
1. Select Advanced >
Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection
Type list, select DHCP.
The screen adjusts:
The modem router automatically detects the information in the following fields:
Router
s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the modem router’s WAN (or Internet) interface. The number after the slash (/) is
the length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
Router
s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the modem router’s LAN interface. The number after the slash (/) is the length of
the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
3. (Optional) In the DHCP User Class (If Required) field, enter a host name.
Most people do not need to fill in this field, but if your ISP has given you a specific host
name, enter it here.
4. (Optional) In the Domain Name (If Required) field, enter a domain name.
You can type the domain name of your IPv6 ISP. (Do not enter the domain name for the
IPv4 ISP here.) For example, if your ISP’
s mail server is mail.xxx.yyy.zzz, you would type
xxx.yyy.zzz as the domain name. If your ISP provided a domain name, type it in this field.
(For example, Earthlink Cable might require a host name of home, and Comcast
sometimes supplies a domain name.)
5. Specify how the modem router assigns IPv6 addresses to the devices on your home
network (the LAN) by selecting one of the following radio buttons:
Advanced Settings
100
N300 Wireless ADSL2+ Modem Router DGN2200v4
Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
Auto Config.
This is the default setting.
6. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the modem router’
s LAN interface.
If you do not specify an ID here, the modem router generates one automatically from its
MAC address.
7. Click the Apply button.
IPv6 PPPoE
To set up a PPPoE IPv6 Internet connection:
1. Select Advanced >
Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection
Type list, select PPPoE.
The screen adjusts:
The modem router automatically detects the information in the following fields:
Router
s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the modem router’s WAN (or Internet) interface. The number after the slash (/) is
the length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
Router
s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the modem router’s LAN interface. The number after the slash (/) is the length of
the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
3. In the Login fields, enter the login information for the ISP connection.
Advanced Settings
101
N300 Wireless ADSL2+ Modem Router DGN2200v4
This is usually the name that you use in your email address. For example, if your main
mail account is JerAB@ISP.com, then you would type JerAB in this field. Some ISPs (like
Mindspring, Earthlink, and T-DSL) require that you use your full email address when you
log in. If your ISP requires your full email address, type it in this field.
4. In the Password field, enter the password for the ISP connection.
5. In the Service Name name field, enter a service name.
If your ISP did not provide a service name, leave this field blank.
Note: The default setting of the Connection Mode field is Always on to provide
a steady IPv6 connection. The modem router never terminates the connection.
If the connection is terminated, for example, when the modem is turned off, the
modem router attempts to reestablish the connection immediately after the
PPPoE connection becomes available again.
6. Specify how the modem router assigns IPv6 addresses to the devices on your home
network (the LAN) by selecting one of the following radio buttons:
Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
Auto Config. This is the default setting.
7. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the modem router’s LAN interface.
If you do not specify an ID here, the modem router generates one automatically from its
MAC address.
8. Click the Apply button.
Advanced Settings
102
N300 Wireless ADSL2+ Modem Router DGN2200v4
Traffic Meter
Traffic metering allows you to monitor the volume of Internet traffic that passes through the
modem router Internet port. You can set limits for traffic volume.
To monitor Internet traffic:
1. Click Advanced >
Advanced Setup > Traffic Meter.
Scroll to view
more settings
2. Select the Enable Traffic Meter check box.
3. (Optional) Control the volume of Internet traf
fic.
You can use either the traffic volume control feature or the connection time control feature
to do this.
Select the T
raffic volume control by radio button and then select one of the
following options:
- No Limit. No restriction is applied when the traf
fic limit is reached.
- Download only.
The restriction is applied to incoming traffic only.
- Both Directions.
The restriction is applied to both incoming and outgoing traffic.
Select the Connection time control radio button and enter the allowed hours in the
Monthly limit field.
4. (Optional) If your ISP charges an amount of extra data volume when you make a new
connection, enter the extra data volume in MB in the Round up data volume for each
connection by field.
5. In the
Traffic Counter section, set the traffic counter to begin at a specific time and date.
If you want the traffic counter to start immediately, click the Restart Counter Now button.
6. In the
Traffic Control section, specify whether the modem router should issue a warning
message before the monthly limit of Mbytes or hours is reached.
By default, the value is 0 and no warning message is issued. You can select one of the
following to occur when the limit is attained:
Advanced Settings
103
N300 Wireless ADSL2+ Modem Router DGN2200v4
The Internet LED flashes green or amber.
The Internet connection is disconnected and disabled.
7. Click the Apply button.
The Internet Traffic Statistics section helps you to monitor the data traffic.
Click the Refresh button to update the Traffic Statistics section.
Click the Traffic Status button to display more information about the data traffic on your
modem router and to change the poll interval.
104
9
9. Virtual Private Networking
This chapter describes how to use the virtual private networking (VPN) features of the modem
router. VPN communications paths are called tunnels. VPN tunnels provide secure, encrypted
communications between your local network and a remote network or computer.
This chapter contains the following sections:
Overview of VPN Configuration
Set Up a Client-to-Gateway VPN
Add a Gateway-to-Gateway VPN Tunnel
Activate a VPN Tunnel
View or Change the Status of a VPN Tunnel
Auto Policy Example
Add or Edit a VPN Auto Policy
Add or Edit a Manual VPN Policy
Virtual Private Networking
105
N300 Wireless ADSL2+ Modem Router DGN2200v4
Overview of VPN Configuration
The modem router supports both client-to-gateway and gateway-to-gateway VPN tunnels.
The modem router supports up to five concurrent tunnels.
Client-to-Gateway VPN Tunnels
Client-to-gateway VPN tunnels provide secure access from a remote computer, such as a
telecommuter connecting to an office network.
Modem router
VPN tunnel
PC running NETGEAR
ProSafe VPN Client
Figure 13. Telecommuter VPN tunnel
A VPN client access allows a remote computer to connect to your network from any location
on the Internet.
Gateway-to-Gateway VPN Tunnels
Gateway-to-gateway VPN tunnels provide secure access between networks, such as a
branch or home office and a main office.
Gateway A
Gateway B
VPN tunnel
(Office)
(Home)
Figure 14. VPN tunnel between networks
A VPN tunnel between gateways is a good way to connect branch or home offices and
business partners over the Internet.
Virtual Private Networking
106
N300 Wireless ADSL2+ Modem Router DGN2200v4
Set Up a Client-to-Gateway VPN
This section describes using the VPN Wizard to set up the VPN tunnel. If you want to
manually specify the settings, see Auto Policy Example on page 112.
To configure a client-to-gateway VPN tunnel:
1. Select Advanced >
Advanced - VPN > VPN Wizard.
2. Click Next.
3. Fill in the Connection Name and pre-shared key fields.
The connection name is for convenience and does not affect how the VPN tunnel
functions.
4. Select A remote VPN client (single computer) radio button and click Next.
The Summary screen displays:
Note: To view the VPNC-recommended authentication and encryption
settings used by the VPN Wizard, click the here link.
Virtual Private Networking
107
N300 Wireless ADSL2+ Modem Router DGN2200v4
5. Click Done.
The VPN Policies screen displays, showing that the new tunnel is enabled:
6. (Optional) To view or modify a tunnel’s settings, select its radio button and click Edit.
7. Use VPN client software on the computer to configure it as a VPN client.
Add a Gateway-to-Gateway VPN Tunnel
This section describes how to use the VPN Wizard to set up the VPN tunnel between two
gateways. The LAN IP address ranges of each VPN endpoint have to be different. The
connection will fail if both are using the default address range of 192.168.0.x.
To add a gateway-to-gateway VPN tunnel:
1. Log in to Gateway
A on LAN A.
2. Select Advanced >
Advanced - VPN > VPN Wizard.
3. Click Next.
Virtual Private Networking
108
N300 Wireless ADSL2+ Modem Router DGN2200v4
4. Fill in the Connection Name and pre-shared key fields. Select the A remote VPN Gateway
radio button and click Next.
5. Fill in the IP address or FQDN for the target VPN endpoint WAN connection, and click Next.
6. Fill in the IP
Address and Subnet Mask fields for the target endpoint that can use this tunnel,
and click Next.
The VPN Wizard Summary screen displays:
To view the VPNC-recommended authentication and encryption settings used by the
VPN Wizard, click the here link.
7. Click Done on the Summary screen.
Virtual Private Networking
109
N300 Wireless ADSL2+ Modem Router DGN2200v4
The VPN Policies screen displays, showing that the new tunnel is enabled.
8. Repeat these steps for the gateway on LAN B, and pay special attention to the following
network settings:
W
AN IP of the remote VPN gateway (for example, 14.15.16.17)
LAN IP settings of the remote VPN gateway:
- IP address (for example, 192.168.0.1)
- Subnet mask (for example, 255.255.255.0)
- Pre-shared key (for example, 12345678)
Activate a VPN Tunnel
To activate a VPN tunnel, you can use the VPN Status screen or start using the tunnel.
To use the VPN Status screen to activate a VPN tunnel:
1. Select Advanced >
Advanced - VPN > VPN Status, and click the VPN Status button.
The Current VPN Tunnels (SAs) screen displays.
2. Click Connect for the VPN tunnel that you want to activate.
To activate a VPN tunnel by using it:
Use a web browser to go to a URL whose IP address or range is covered by the policy for
that VPN tunnel.
Virtual Private Networking
110
N300 Wireless ADSL2+ Modem Router DGN2200v4
View or Change the Status of a VPN Tunnel
The VPN Status/Log screen displays the status.
To check the status of a VPN tunnel:
1. Select Advanced >
Advanced - VPN > VPN Status.
The VPN Status/Log screen displays:
This log shows the details of recent VPN activity, including the building of the VPN tunnel.
If there is a problem with the VPN tunnel, refer to the log for information about what might
be the cause of the problem.
2. (Optional) Click Refresh to see the most recent entries.
3. (Optional) Click Clear Log to delete all log entries.
4. Click the VPN Status button.
The Current VPN Tunnels (SAs) screen displays.
This screen lists the following data for each active VPN tunnel.
SPI. Each SA has a unique (security parameter index (SPI) for traf
fic in each
direction. For manual key exchange, the SPI is specified in the policy definition. For
automatic key exchange, the SPI is generated by the IKE protocol.
Policy Name.
The VPN policy associated with this SA.
Remote Endpoint.
The IP address on the remote VPN endpoint.
Action. Either a Drop or a Connect button.
Virtual Private Networking
111
N300 Wireless ADSL2+ Modem Router DGN2200v4
SLifeTime (Secs). The remaining soft lifetime for this SA in seconds. When the soft
lifetime becomes 0 (zero), the SA (security association) is renegotiated.
HLifeT
ime (Secs). The remaining hard lifetime for this SA in seconds. When the hard
lifetime becomes 0 (zero), the SA (security association) is terminated. (It is
reestablished if necessary.)
Deactivate a VPN Tunnel
Sometimes a VPN tunnel has to be deactivated for testing purposes. You can deactivate a
VPN tunnel from two places:
Policy table on VPN Policies screen
VPN Status screen
To use the Policy Table to deactivate a VPN tunnel:
1. Select Advanced >
Advanced - VPN > VPN Policies.
2. In the Policy Table, clear the Enable check box for the VPN tunnel that you want to
deactivate.
3. Click Apply.
To reactivate the tunnel, select the Enable check box and click Apply.
To use the VPN Status Screen to deactivate a VPN tunnel:
1. Advanced >
Advanced - VPN > VPN Status, and click the VPN Status button.
The Current VPN Tunnels (SAs) screen displays:
2. Click Drop for the VPN tunnel that you want to deactivate.
Virtual Private Networking
112
N300 Wireless ADSL2+ Modem Router DGN2200v4
Delete a VPN Tunnel
To delete VPN tunnel:
1. Select Advanced >
Advanced - VPN > VPN Policies.
2. Select the radio button for the VPN tunnel.
3. Click Delete.
Auto Policy Example
You need to configure matching VPN settings on both VPN endpoints. The outbound VPN
settings on one end have to match to the inbound VPN settings on other end, and vice versa
Auto policy creates a typical automated Internet Key Exchange (IKE) setup. Auto Policy uses
the IKE protocol to define the authentication scheme and automatically generate the
encryption keys.
Gateway A
Gateway B
VPN Tunnel
22.23.24.25
14.15.16.17
IP: 192.168.0.1
IP:192.168.3.1
Figure 15. Example of an Auto policy for a gateway-to-gateway tunnel
Virtual Private Networking
113
N300 Wireless ADSL2+ Modem Router DGN2200v4
Add or Edit a VPN Auto Policy
An Auto VPN policy uses the IKE (Internet Key Protocol) to exchange and negotiate
parameters for the IPSec SA (security association). Because of this negotiation, not all of the
settings on this VPN gateway have to match the settings on the remote VPN endpoint.
Where settings have to match, this requirement is indicated.
To add an Auto policy:
1. Set the LAN IPs on each gateway to dif
ferent subnets and configure each correctly for
the Internet.
2. Select Advanced > Advanced - VPN > VPN Policies and click the Add Auto
Policy
button.
3. Specify the general settings:
In the Policy Name field, enter a unique name.
This name is not supplied to the remote VPN endpoint. It is used only to help you
manage the policies.
From the
Address Type list, select Fully Qualified Domain Name, Dynamic IP
Address or Fixed IP Address.
You can set up multiple remote dynamic IP policies, but only one policy can be
enabled at a time.
If you want to ensure that a connection is kept open, or, if that is not possible, it is
quickly reestablished when disconnected, select the IKE Keep Alive check box and
fill in the Ping IP Address field.
Fill in the Ping IP
Address field.
The ping IP address has to be associated with the remote endpoint. Either the WAN
or a LAN address can be used; a LAN address is preferable.
This IP address is
pinged to generate some traffic for the VPN tunnel.
Virtual Private Networking
114
N300 Wireless ADSL2+ Modem Router DGN2200v4
4. Specify the Local LAN settings:
From the IP Address list, select Subnet address, Single address, or Range
address.
Fill in the Single/Start IP Address field.
If you are specifying a range, fill in the Finish IP Address field.
This range must be an address range used on your LAN. For a single IP address, do
not fill in the Finish IP Address field.
The remote VPN endpoint must have these IP addresses entered as its remote
addresses.
5. Specify the Remote LAN settings.
From the IP Address list, select Single PC -no Subnet, Single address, Range
address, or Subnet address.
If there is no LAN (only a single computer) at the remote endpoint, select the Single
PC -no Subnet option. The Single address option is typically used to access a server
on the remote LAN.
If you want to specify a range, fill in the Finish IP Address field.
This range must be an address range used on the remote LAN.
Fill in the Subnet Mask field.
The remote VPN endpoint must have these IP addresses entered as its local addresses.
6. Specify the IKE settings:
From the Direction list, select either Responder only or Initiator and Responder.
The modem router uses this setting to determine if the IKE policy matches the current
traffic. With the Responder only setting, incoming connections are allowed and
outgoing connections are blocked. With the Initiator and Responder setting, both
incoming and outgoing connections are allowed.
Ensure that the remote VPN endpoint is set to use Main Mode.
Select the Diffie-Hellman (DH) Group from the list.
The Diffie-Hellman algorithm is used when keys are exchanged. The DH Group
setting determines the bit size used in the exchange. This value needs to match the
value used on the remote VPN gateway.
Select the local identity type.
Select an option to match the Remote Identity Type setting on the remote VPN
endpoint.
- WAN IP Address. Your Internet IP address.
- Fully Qualified Domain Name. Your domain name.
- Fully Qualified User Name. Your name, email address, or other ID.
Select the remote identity type.
Virtual Private Networking
115
N300 Wireless ADSL2+ Modem Router DGN2200v4
Select the option that matches the Local Identity Type setting on the remote VPN
endpoint.
- IP Address. The Internet IP address of the remote VPN endpoint.
- Fully Qualified Domain Name. The domain name of the remote VPN endpoint.
- Fully Qualified User Name. The name, email address, or other ID of the remote
VPN endpoint.
7. Specify the following parameters:
Select the encryption algorithm.
This is the encryption algorithm used for both IKE and IPSec. This setting has to
match the setting used on the remote VPN gateway. DES and 3DES are supported.
- DES. The Data Encryption Standard (DES) processes input data that is 64 bits
wide, encrypting these values using a 56-bit key. Faster but less secure than
3DES.
- 3DES. (Triple DES) achieves a higher level of security by encrypting the data
three times using DES with three different, unrelated keys.
Select the authentication algorithm.
This is the authentication algorithm used for both IKE and IPSec. This setting has to
match the setting used on the remote VPN gateway. Auto, MD5, and SHA-1 are
supported. Auto negotiates with the remote VPN endpoint and is not available in
responder-only mode.
- MD5. 128 bits, faster but less secure.
- SHA-1. 160 bits, slower but more secure. This is the default.
Enter the pre-shared key.
The key has to be entered both here and on the remote VPN gateway.
Enter the SA life time value.
This value is the time interval before the SA (security association) expires. (It is
automatically reestablished as required.) While using a short time period (or data
amount) increases security, it also degrades performance. It is common to use
periods over an hour (3600 seconds) for the SA life time. This setting applies to both
IKE and IPSec SAs.
If you want enhanced security, select the Enable IPSec PFS (Perfect Forward
Secrecy) check box.
If this check box is selected, security is enhanced by ensuring that the key is changed
at regular intervals. Also, even if one key is broken, subsequent keys are no easier to
break. (Each key has no relationship to the previous key.)
This setting applies to both IKE and IPSec SAs. When configuring the remote
endpoint to match this setting, you might have to specify the key group used. For this
device, the key group is the same as the DH Group setting in the IKE section.
8. Click Apply.
Virtual Private Networking
116
N300 Wireless ADSL2+ Modem Router DGN2200v4
The VPN Policies screen displays:
9. Repeat these steps for the gateway on LAN B.
Pay special attention to the following network settings:
General, Remote
Address Data (for example, 14.15.16.17)
Remote LAN, Start IP
Address
- IP
Address (for example, 192.168.0.1)
- Subnet Mask (for example, 255.255.255.0)
- Pre-shared Key (for example, 12345678)
10. T
o activate the VPN tunnel, start using it, or use the VPN Status screen (select the tunnel
and click Connect).
Virtual Private Networking
117
N300 Wireless ADSL2+ Modem Router DGN2200v4
Add or Edit a Manual VPN Policy
A manual VPN policy requires all settings for the VPN tunnel to be manually entered at each
end (both VPN endpoints).
To add or edit a manual policy:
1. Select Advanced >
Advanced - VPN > VPN Policies and click the Add Manual Policy
radio button.
The VPN - Manual Policy screen displays.
2. Specify the general settings:
In the Policy Name field, enter a unique name.
This name is not supplied to the remote VPN endpoint. It is used only to help you
manage the policies.
From the
Address Type list, select Fully Qualified Domain Name, or select Fixed IP
Address and fill in the Address Data field.
You can set up multiple remote dynamic IP policies, but only one such policy can be
enabled at a time.
3. Specify the Local LAN settings:
From the IP
Address list, select Subnet address, Single address, or Range
address.
Fill in the Single/Start IP
Address field.
If you are specifying a range, fill in the Finish IP
Address field.
This range must be an address range used on your LAN. For a single IP address, do
not fill in the Finish IP
Address field.
The remote VPN endpoint must have these IP addresses entered as its remote
addresses.
Virtual Private Networking
118
N300 Wireless ADSL2+ Modem Router DGN2200v4
4. Specify the Remote LAN settings.
From the IP Address list, select Single PC -no Subnet, Single address, Range
address, or Subnet address.
If there is no LAN (only a single computer) at the remote endpoint, select the Single
PC -no Subnet option. The Single address option is typically used to access a server
on the remote LAN.
If you want to specify a range, fill in the Finish IP Address field.
This range must be an address range used on the remote LAN.
Fill in the Subnet Mask field.
The remote VPN endpoint must have these IP addresses entered as its local addresses.
5. Specify the ESP (Encapsulating Security Payload) settings:
ESP provides security for the payload (data) sent through the VPN tunnel.
In the SPI field, enter the required security policy indexes (SPIs).
Each policy has to have unique SPIs. These settings need to match the remote VPN
endpoint. The in setting here has to match the out setting on the remote VPN
endpoint, and the out setting here has to match the in setting on the remote VPN
endpoint.
From the Encryption list, select DES or 3DES, and fill in the Key field.
For 3DES, the keys should be 24 ASCII characters, and for DES, the keys should be
8 ASCII characters.
- DES. The Data Encryption Standard (DES) processes input data that is 64 bits
wide, encrypting these values using a 56-bit key. Faster but less secure than
3DES.
- 3DES. (Triple DES) achieves a higher level of security by encrypting the data
three times using DES with three different, unrelated keys.
From the Authentication list, select MD5 or SHA-1, and fill in the Key field.
119
10
10. Troubleshooting
This chapter provides information to help you diagnose and solve problems you might have with
your modem router. If you do not find the solution here, check the NETGEAR support site at
http://support.netgear.com for product and contact information.
This chapter contains the following sections:
Troubleshoot with the LEDs
Cannot Log In to the Modem Router
Troubleshoot the Internet Connection
TCP/IP Network Not Responding
Changes Not Saved
Incorrect Date or Time
Troubleshooting
120
N300 Wireless ADSL2+ Modem Router DGN2200v4
Troubleshoot with the LEDs
When you turn on the power, the power, LAN, and DSL LEDs should light as described here.
If they do not, refer to the sections that follow for help.
1. When power is first applied, the Power LED lights.
2. After approximately 10 seconds, the LAN and DSL LEDs light as follows:
a. The LAN port LEDs light for any local ports that are connected.
b. The DSL link LED lights green to indicate that a DSL link is established.
c. If a LAN port is connected to a 100 Mbps device, verify that the LAN port’s LED is
green. If the LAN port is 10 Mbps, the LED is amber.
Power LED Is Off
If the Power and other LEDs are off when your modem router is turned on:
Check that the power cord is correctly connected to your modem router and the power
supply adapter is correctly connected to a functioning power outlet.
Check that you are using the 12 V DC power adapter supplied by NETGEAR for this
product.
If the error persists, you could have a hardware problem and should contact NETGEAR
technical support.
Power LED Is Red
When the modem router is turned on, it performs a power-on self-test, during which time the
Power LED turns red. If the Power LED does not turn green within a minute or so or if it turns
red at any other time during normal operation, there is a fault within the modem router.
If the Power LED turns red to indicate a modem router fault, turn the power off and on to see
if the modem router recovers. If the Power LED is still red 1 minute after power-up:
Turn the power off and on one more time to see if the modem router recovers.
Clear the modem router’s configuration to factory defaults as explained in Factory
Settings on page 128. This sets the modem router’s IP address to 192.168.0.1.
If the error persists, you could have a hardware problem and should contact NETGEAR
technical support.
LAN LED Is Off
If the LAN LED for a port does not light when you connect a device, check the following:
The Ethernet cable connections are secure at the modem router and at the hub or device.
The power is turned on to the connected hub or device.
Troubleshooting
121
N300 Wireless ADSL2+ Modem Router DGN2200v4
You are using the correct cable.
Cannot Log In to the Modem Router
If you are unable to log in to the modem router from a computer on your local network, check
the following:
If you are using an Ethernet-connected computer, check the Ethernet connection
between the computer and the modem router as described in the previous section.
Make sure that your computers IP address is on the same subnet as the modem router.
If you are using the recommended addressing scheme, your computers address should
be in the range of 192.168.0.2 to 192.168.0.254.
If your computers IP address is shown as 169.254.x.x, recent versions of Windows and
Mac OS generate and assign an IP address if the computer cannot reach a DHCP server.
These autogenerated addresses are in the range of 169.254.x.x. If your IP address is in
this range, check the connection from the computer to the modem router, and reboot your
computer.
If your modem router’s IP address was changed and you do not know the current IP
address, clear the modem router’s configuration to factory defaults. This sets the modem
router’s IP address to 192.168.0.1. This procedure is explained in
Factory Settings on
page 128.
Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using
Internet Explorer, click Refresh to be sure that the Java applet is loaded.
Try quitting the browser and launching it again.
Make sure that you are using the correct login information. The factory default login name
is admin, and the password is password. Make sure that Caps Lock is off when you
enter this information.
Troubleshooting
122
N300 Wireless ADSL2+ Modem Router DGN2200v4
Troubleshoot the Internet Connection
If your modem router is unable to access the Internet, check the ADSL connection, then the
WAN TCP/IP connection.
ADSL Link
If your modem router is unable to access the Internet, first determine whether you have an
ADSL link with the service provider. The state of this connection is indicated with the Internet
LED.
ADSL Link LED Is Green
If your ADSL link LED is green, you have a good ADSL connection. You can be confident that
the service provider has connected your line correctly and that your wiring is correct.
ADSL Link LED Is Blinking Green
If your ADSL link LED is blinking green, your modem router is attempting to make an ADSL
connection with the service provider. The LED should turn green within several minutes.
If the ADSL link LED does not turn green, disconnect all telephones on the line. If this solves
the problem, reconnect the telephones one at a time, being sure to use a microfilter on each
telephone. If the microfilters are connected correctly, you should be able to connect all your
telephones.
If disconnecting telephones does not result in a green ADSL link LED, there might be a
problem with your wiring. If the telephone company has tested the ADSL signal at your
network interface device (NID), then you might have poor-quality wiring in your house.
ADSL Link LED Is Off
If the ADSL link LED is off, disconnect all telephones on the line. If this solves the problem,
reconnect the telephones one at a time, being sure to use a microfilter on each telephone. If
the microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green ADSL link LED, check for the following:
Check that the telephone company has made the connection to your line and tested it.
Verify that you are connected to the correct telephone line. If you have more than one
phone line, be sure that you are connected to the line with the ADSL service. It might be
necessary to use a swapper if your ADSL signal is on pins 1 and 4 or the RJ-11 jack. The
modem router uses pins 2 and 3.
Internet LED Is Red
If the Internet LED is red, the device was unable to connect to the Internet. Verify the
following:
Troubleshooting
123
N300 Wireless ADSL2+ Modem Router DGN2200v4
Check that your login credentials are correct, or that the information you entered on the
Internet Setup screen is correct.
Check if your ISP has a problem—it might not be that the modem router cannot connect
to the Internet, but rather that your ISP that cannot provide an Internet connection.
Obtaining an Internet IP Address
If your modem router is unable to access the Internet, and your Internet LED is green, see if
the modem router can obtain an Internet IP address from the ISP. Unless you have been
assigned a static IP address, your modem router requests an IP address from the ISP. You
can determine whether the request was successful using the browser interface.
To check the Internet IP address from the browser interface:
1. Launch your browser, and select an external site such as www.netgear.com.
2. Access the main menu of the modem router’s configuration at http://192.168.0.1.
3. Click the Advanced tab and check that an IP address is shown for the WAN port.
If 0.0.0.0 is shown, your modem router has not obtained an IP address from your ISP.
If your modem router is unable to obtain an IP address from the ISP, the problem might be
one of the following:
If you have selected a login program, the service name, user name, or password might be
incorrectly set. See the following section,
Troubleshoot PPPoE or PPPoA .
Your ISP might check for your computers host name. Assign the computer host name of
your ISP account to the modem router in the browser-based Setup Wizard.
Your ISP allows only one Ethernet MAC address to connect to Internet, and might check
for your computers MAC address. In this case, do one of the following:
- Inform your ISP that you have bought a new network device, and ask them to use the
modem router’s MAC address.
- Configure your modem router to spoof your computers MAC address. This can be
done in the Basic Settings screen.
Troubleshoot PPPoE or PPPoA
To debut the PPPoE or PPPoA connection:
1. Access the main menu of the modem router at http://192.168.0.1.
2. Select Maintenance > Router Status.
3. Click the Connection Status button.
If all of the steps indicate OK, your PPPoE or PPPoA connection is up and working.
If any of the steps indicates Failed, you can attempt to reconnect by clicking Connect. The
modem router continues to attempt to connect indefinitely.
If you cannot connect after several minutes, you might be using an incorrect service name,
user name, or password. There also might be a provisioning problem with your ISP.
Troubleshooting
124
N300 Wireless ADSL2+ Modem Router DGN2200v4
Unless you connect manually, the modem router does not authenticate using PPPoE or
PPPoA until data is transmitted to the network.
Troubleshoot Internet Browsing
If your modem router can obtain an IP address, but your computer is unable to load any web
pages from the Internet:
Your computer might not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www
addresses) to numeric IP
addresses. Typically your ISP provides the addresses of one or
two DNS servers for your use. If you entered a DNS address when you set up the modem
router, reboot your computer, and verify the DNS address. Alternatively, you can
configure your computer manually with DNS addresses, as explained in your operating
system documentation.
Your computer might not have the modem router configured as its TCP/IP modem router.
If your computer obtains its information from the modem router by DHCP, reboot the
computer, and verify the modem router address.
TCP/IP Network Not Responding
Most TCP/IP terminal devices and routers have a ping utility for sending an echo request
packet to the designated device. The device responds with an echo reply to tell whether a
TCP/IP network is responding to requests.
Test the LAN Path to Your Modem Router
You can ping the modem router from your computer to verify that the LAN path to your
modem router is set up correctly.
To ping the modem router from a computer running Windows 95 or later:
1. From the Windows taskbar, click the Start button, and select Run.
2. In the field provided, type ping followed by the IP address of the modem router, as in this
example:
ping 192.168.0.1
3. Click OK.
You should see a message like this one:
Pinging <IP address> with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
Troubleshooting
125
N300 Wireless ADSL2+ Modem Router DGN2200v4
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
Wrong physical connections
Make sure that the LAN port LED is lit. If the LED is off, follow the instructions in LAN
LED Is Off on page 120.
Wrong network configuration
- Verify that the Ethernet card driver software and TCP/IP software are both
installed and configured on your computer or workstation.
- Verify that the IP address for your modem router and your workstation are correct
and that the addresses are on the same subnet.
Test the Path from Your Computer to a Remote Device
After you verify that the LAN path works correctly, test the path from your computer to a
remote device. In the Windows Run screen, type:
ping -n 10 IP address
where IP address is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as described in Test the LAN Path to Your Modem
Router on page 124 display. If you do not receive replies:
Check that your computer has the IP address of your modem router listed as the default
modem router. If the IP configuration of your computer is assigned by DHCP, this
information is not visible in your computers Network Control Panel. Verify that the IP
address of the modem router is listed as the default router.
Check that the network address of your computer (the portion of the IP address specified
by the netmask) is different from the network address of the remote device.
Check that your cable or DSL modem is connected and functioning.
If your ISP assigned a host name to your computer, enter that host name as the account
name in the Internet Setup screen.
Your ISP could be rejecting the Ethernet MAC addresses of all but one of your
computers. Many broadband ISPs restrict access by allowing traffic only from the MAC
address of your modem, but some additionally restrict access to the MAC address of a
single computer connected to that modem. In this case, configure your modem router to
clone or spoof the MAC address from the authorized computer.
Changes Not Saved
If the modem router does not save the changes you make in the modem router interface,
check the following:
Troubleshooting
126
N300 Wireless ADSL2+ Modem Router DGN2200v4
When entering configuration settings, always click the Apply button before moving to
another screen or tab, or your changes are lost.
Click the Refresh or Reload button in the web browser. The changes might have
occurred, but the old settings might be in the web browsers cache.
Incorrect Date or Time
The modem router uses the Network Time Protocol (NTP) to obtain the current time from one
of several network time servers on the Internet. Each entry in the log is stamped with the date
and time of day. Problems with the date and time function can include the following:
Date shown is January 1, 2003. This means the modem router has not yet reached a
network time server. Check that your Internet access is configured correctly. If you have
just finished setting up the modem router, wait at least 5 minutes, and check the date and
time again.
Time is off by one hour. The modem router has an automatic daylight savings time
setting.
To change the modem router setting for daylight savings time:
1. Select Security > Schedule.
2. Select the Automatically adjust for daylight savings time check box.
3. Click Apply.
Your change is saved.
127
A
A. Supplemental Information
This appendix includes the factory default settings and technical specifications for the modem
router, and instructions for wall-mounting the unit.
This appendix contains the following sections:
Factory Settings
Specifications
Supplemental Information
128
N300 Wireless ADSL2+ Modem Router DGN2200v4
Factory Settings
You can return the modem router to its factory settings. On the back of the modem router, use
the end of a paper clip or some other similar object to press and hold the Reset button for at
least 7 seconds. The modem router returns to the factory settings shown in the following
table.
Table 4. Factory default settings
Feature Default Behavior
Router Login User login URL www.routerlogin.com or /www.routerlogin.net
User name (case-sensitive) admin
Login password (case-sensitive) password
Internet
connection
WAN MAC address Use default address
WAN MTU size 1492
Port speed AutoSensing
Local network
(LAN)
LAN IP 192.168.0.1
Subnet mask 255.255.255.0
RIP direction None
RIP version Disabled
RIP authentication None
DHCP server Enabled
DHCP starting IP address 192.168.0.2
DHCP ending IP address 192.168.0.254
DMZ Enabled or disabled
Time zone GMT for WW except GR, GMT+1 for GR, GMT-8 for NA
Time zone adjusted for daylight
savings time
Disabled
SNMP Disabled
Firewall Inbound (communications coming
in from the Internet)
Disabled (except traffic on port 80, the HTTP port)
Outbound (communications going
out to the Internet)
Enabled (all)
Source MAC filtering Disabled
Supplemental Information
129
N300 Wireless ADSL2+ Modem Router DGN2200v4
Wireless Wireless communication Enabled
SSID name Can be found on the label on the bottom of the unit.
Security Can be found on the label on the bottom of the unit.
Broadcast SSID Enabled
Country/region United States (in North America; otherwise, varies by
region)
RF channel Auto
Operating mode Up to 145 Mbps
Data rate Best
Output power Full
Access point Enabled
Authentication type Pre-shared Key
Wireless card access list All wireless stations allowed
Table 4. Factory default settings (Continued)
Feature Default Behavior
Supplemental Information
130
N300 Wireless ADSL2+ Modem Router DGN2200v4
Specifications
Table 5.
Specification Description
Network protocol and
standards compatibility
TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or
Routed Ethernet, and RFC 1577 Classical IP over
ATM
Power adapter North America: 120V, 60 Hz, input
UK, Australia: 240V, 50 Hz, input
Europe: 230V, 50 Hz, input
All regions (output): 12V @ 1A output
Physical Dimensions: 6.80 in. x 5.03 in. x 1.28 in. (173 mm x 128 mm x 33 mm)
Weight: 0.65 lbs. without the stand (0.29 kg)
Environmental Operating temperature: 0° to 40° C (32º to 104º F)
Operating humidity: 10% to 90% relative humidity, noncondensing
Storage temperature: –20° to 70° C (–4º to 158º F)
Storage humidity: 5 to 95% relative humidity, noncondensing
Regulatory compliance FCC Part 15 Class B, FCC Part 68, VCCI Class B; EN 55 022 (CISPR 22),
Class B
Interface specifications LAN: 10BASE-T or 100BASE-Tx, RJ-45
WAN: ADSL, Dual RJ-11, pins 2 and 3
T1.413, G.DMT, G.Lite
ITU Annex A hardware or Annex B hardware
ITU G.992.5 (ADSL2+)
131
B
B. Notification of Compliance
NETGEAR wireless routers, gateways, APs
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National laws for usage of radio
spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may
result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.
This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all
options described in this user's guide may not be available in your version of the product.
Europe – EU Declaration of Conformity
Products bearing the marking comply with the following EU directives:
EMC Directive 2004/108/EC
Low V
oltage Directive 2006/95/EC
If this product has telecommunications functionality, it also complies with the requirements of the following EU
Directive:
R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to harmonized European standards that are noted in the EU
Declaration of Conformity
.
Intended for indoor use only in all EU member states, EFTA states, and Switzerland.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may
be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should
contact the national spectrum authority in France.
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only.
Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Declaration of Conformity
We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the
N300 Wireless ADSL2+ Modem Router DGN2200v4 complies with Part 15 Subpart B of FCC CFR47 Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
N300 Wireless ADSL2+ Modem Router DGN2200v4
Notification of Compliance
132
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following methods:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the
users authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not
possible.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or
transmitter.
FCC Part 68
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the
product label of this equipment is a label that contains, among other information, a product identifier in the
format US:5NHDL01BDGN2200v4. If requested, this number must be provided to the telephone company.
TV Tuner (on Selected Models)
Note to CATV System Installer: This reminder is provided to call the CATV system installer’s attention to Section
820-93 of the National Electrical Code, which provides guidelines for proper grounding and, in particular, specifies that
the Coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as
possible.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (N300 Wireless ADSL2+ Modem Router DGN2200v4) does not exceed the Class B limits for
radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada
Industry Canada
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE: Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
Caution:
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
N300 Wireless ADSL2+ Modem Router DGN2200v4
Notification of Compliance
133
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
NOTE IMPORTANTE: Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
Interference Reduction Table
The table below shows the recommended minimum distance between NETGEAR equipment and household
appliances to reduce interference (in feet and meters).
Household Appliance Recommended Minimum Distance
(in feet and meters)
Microwave ovens 30 feet / 9 meters
Baby Monitor - Analog 20 feet / 6 meters
Baby Monitor - Digital 40 feet / 12 meters
Cordless phone - Analog 20 feet / 6 meters
Cordless phone - Digital 30 feet / 9 meters
Bluetooth devices 20 feet / 6 meters
ZigBee 20 feet / 6 meters
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Netgear DGN2200Bv4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Netgear DGN2200Bv4 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Netgear DGN2200Bv4

Netgear DGN2200Bv4 Installatiehandleiding - Deutsch - 14 pagina's

Netgear DGN2200Bv4 Gebruiksaanwijzing - Deutsch - 146 pagina's

Netgear DGN2200Bv4 Installatiehandleiding - English - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info