en Cleaning function
28
Final cleaning
1. Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2. Clean the smooth surfaces in the cooking
compartment with a dish cloth or a soft brush.
Stubborn residues can be removed using a stainless
steel scouring pad.
3. Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4. Use the # touch button to switch off the appliance.
5. Leave the appliance door ajar in the locking position
(approx. 30°) for approx. 1 hour to allow the enamel
surfaces in the cooking compartment to dry.
Alternatively, you can also run the rapid drying
function for the cooking compartment.
Running the rapid drying function for the cooking
compartment
1. After the cleaning aid process has finished, leave the
appliance door ajar in the locking position (approx.
30°).
2. Touch the # touch button.
3. Start CircoTherm hot air at 50 °C.
4. After 5 minutes, switch off the appliance and close
the appliance door.
Removing heavy deposits of dirt
You have several options for removing particularly
stubborn deposits of dirt.
■ Leave the soapy water to work for some time before
starting the cleaning aid.
■ Rub soapy water onto the dirt on the smooth
surfaces before starting the cleaning aid.
■ Repeat the cleaning aid once the cooking
compartment has cooled down.
Descaling
The appliance must be descaled regularly in order for it
to continue operating correctly.
There are several steps in the descaling programme.
For hygiene reasons, the descaling programme must
be run through completely so that the appliance can be
ready for operation again.In total, the descaling
programme runs for approx. 70-90 minutes.
■ Descale (approx. 55-70 minutes), then empty and
refill the water tank
■ First rinsing cycle (approx. 6-9 minutes), then empty
and refill the water tank
■ Second rinsing cycle (approx. 6-9 minutes), then
empty and dry the water tank
If the descaling process is interrupted (for example, due
to a power failure or because the appliance has been
switched off), you are prompted to rinse the appliance
twice after it is switched back on. The appliance cannot
be used until the second rinsing cycle has come to an
end.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible, or fewer, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Starting
Caution!
Damage to the appliance: Only use liquid descalers
recommended by us for the descaling programme.
Other descalers may damage the appliance.
Descaler order no.: 311 680
Caution!
Descaling solution: Do not allow descaling solution to
come into contact with the control panel or other
sensitive surfaces. This will damage the surfaces. If this
does happen, remove the descaling solution
immediately with water.
The descaling programme can only be started once the
cooking compartment has completely cooled down. If
the temperature in the cooking compartment is too
high, a message appears on the display. Wait until the
cooking compartment has cooled down. Then restart
the process.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
1. Mix 500 ml water with 150 ml liquid descaler to
make a descaling solution.
2. Touch the # touch button.
3. Remove the water tank and fill with descaling
solution.
4. Fully insert the water tank filled with the descaling
solution.
5. Close the control panel.
6. Touch the 0 touch button.
7. Swipe to the left or right to select "Descale ,".
8. Touch the bottom line.
The duration of the descaling programme is
displayed. It cannot be changed.
9. Touch the bottom line.
10. Touch the # touch button.
The appliance is descaled. The remaining time
counts down on the display. As soon as the
descaling programme has finished, an audible
signal sounds.
