727330
4
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
4
a
Quick start guide
Smoke alarm DTCTSL50WT
For more information see
the extended manual online:
ned.is/dtctsl50wt
Intended use
This product is intended for smoke detection. Other
uses or changes to the product constitute improper
use and carry serious risk of accidents. This product
is for indoor use only. This product is not intended
for commercial use.
The product must not be mounted in damp rooms,
near doors, windows, ventilators or radiators.
Any modication of the product may have
consequences for safety, warranty and proper
functioning.
Main parts (image A)
Smoke alarm
Indicator LED
“Test / Hush button
Magnet
Mounting bracket
Screw (3 x 25 mm)
Plug (6 x 28 mm)
Preparation (image B - D)
Install the product on the wall or ceiling.
The product must be installed:
In each room.
On each oor.
In the hallway.
In the staircase.
In the storage room.
In spaces with electric equipment.
-
Do not install in the tip of a sloping ceiling as
smoke-free air can collect in these areas.
Install the product on the ceiling where 1 m from
the highest point of the ceiling.
Install the product at least 61 cm from the corner
of the wall.
Install the product at least 50 cm from
uorescent light sources.
Installation of the product (image E)
1. Turn A
5
counterclockwise to remove it from
A
1
.
2. Remove A
4
from A
1
to switch on the
product.
3. Place A
5
in the desired location.
4. Use A
5
to mark the drill locations with a pencil.
5. Drill two Ø 6 mm holes.
6. Insert the plugs.
7. Fasten the mounting bracket with A
6
.
8. Turn A
1
clockwise to attach it to A
5
.
Testing the product
The product must be tested to ensure proper
operation.
1. Press and hold A
3
until the product emits a
continuous “beep” and A
2
starts blinking.
2. Release A
3
. The “beep” stops and A
2
stops
blinking.
The product is now in hush mode.
3. Repeat the above steps to exit the hush mode
and nish the test.
Hush mode
In hush mode, the product does not detect smoke
for 9 minutes.
The hush mode must be activated manually.
1. Press A
3
shortly to activate hush mode. The
LED blinks every 10 seconds.
After 9 minutes, the product goes back into standby
mode.
Tip: To leave the hush mode early, hold down A
3
until the product emits a “beep”.
4
Note: In hush mode, the alarm is still triggered
when the smoke concentration in the ambience
is over 4 times the minimum alarming value.
Status of smoke alarm
LED light Sound alarm
Standby mode Blinks every
344 s
O
Hush mode Blinks every
10 s
O
Test Blinks
continuously
Continuous
“beep”
Low-battery
condition
No LED
function
A “beep” every
43 s
Malfunction
or end-of-life
No LED
function
A series of
“beeps” every
43 s
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nedis DTCTSL50WT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nedis DTCTSL50WT in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Nedis DTCTSL50WT

Nedis DTCTSL50WT Gebruiksaanwijzing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info