214807
62
Verklein
Vergroot
Pagina terug
1/75
Pagina verder
54
7. Appendix
Common Problems & Solutions ( "Power/Status/Lamp Indicator" on page 53.)
Does not turn on
or shut down
Will turn off
No picture
Picture suddenly
becomes dark
Color tone or hue is
unusual
Image isn’t square to
the screen
Picture is blurred
Flicker appears on
screen
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or blinking
Cross color in RGB
mode
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. ( pages 17 and 18)
Ensure that the lamp cover is installed correctly. ( page 52)
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the
room where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if the lamp usage exceeds 2100 hours (up to 3100 hours : Eco mode). If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. ( page 47)
The lamp may fail to light. Wait a full minute and then turn on the power again.
Set [Fan Mode] to [High Altitude] when using the projector at altitudes approximately 5500 feet/1600 meters
or higher. Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to
[High Altitude] can cause the projector to overheat and the projector could shut down. If this happens, wait a
couple minutes and turn on the projector. ( page 45)
Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before
the projector has cooled down, the fan will run a short time before the lamp will turn on.
Ensure that the Power Management or Off Timer is off. ( page 44)
Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select
your source (Computer, Video or S-Video). ( page 20) If there is still no picture, press the button again.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. ( page 40)
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the [Reset] in the Menu. ( page 47)
Enter your registered keyword if the Security function is enabled. ( page 29)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
See also the next page.
When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
* When there are no signals To return to the Normal mode, select another available source.
* When the room where you' re presenting is particularly warm Move the projector to a cooler location, or
set [Fan Mode] to [High]. ( page 45)
Check if an appropriate color is selected in [Wall Color]. If so, select an appropriate option. ( page 42)
Adjust [Hue] in [Picture]. ( page 40)
Reposition the projector to improve its angle to the screen. ( page 21)
Use the Keystone correction function to correct the trapezoid distortion. ( page 23)
Adjust the focus. ( page 22)
Reposition the projector to improve its angle to the screen. ( page 21)
Ensure that the distance between the projector and screen is within the adjustment range of the lens.
( page 10)
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Set [Fan Mode] to other than [High Altitude] mode when using the projector at altitudes approximately 5500 feet/1600
meters or lower. Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [High
Altitude] can cause the lamp to overcool, causing the image to flicker. Switch [Fan Mode] to [Auto]. ( page 45)
Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select
your source (Computer, Video or S-Video). ( page 20)
Adjust the computer image manually with the Horizontal/Vertical in the [Image Options]. ( page 41)
Install new batteries.( page 8)
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. ( page 8)
See the POWER/STATUS/LAMP Indicator. ( page 53)
Press the AUTO ADJ. button on the projector cabinet or the remote control. ( page 25)
Adjust the computer image manually with Clock/Phase in [Image Options] in the menu. ( page 41)
Problem Check These Items
For more information contact your dealer.
62

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nec vt 700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nec vt 700 in de taal/talen: Engels als bijlage per email.

De handleiding is 3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info