215755
86
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
77
8. Appendx
Common Problems & Solutons ("Power/Status/LampIndicator"onpage76.)
Problem Check These Items
Does not turn on Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control
is on. ( page 15, 16)
Ensure that the lamp cover is installed correctly. (
page 74)
Ensure that the two screws on the lamp housing are completely tightened.(
page 74)
Ensure that the cooling pump is installed correctly. (
page 75)
Check to see if the projector has overheated. If there is insufcient ventilation around the projector or if the room
where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its
life. If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. (
page 70)
The lamp may fail to light. Wait a full minute and then turn on the power again.
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5000 feet/1500 meters
or higher. Using the projector at altitudes approximately 5000 feet/1500 meters or higher without setting to [HIGH
ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens, wait a couple
minutes and turn on the projector. ( page 65)
Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before the
projector has cooled down, the fan will run a short time before the lamp will turn on.
Will turn off Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. ( page 66, 67)
No picture Use the appropriate source button on the remote control to select your source. ( page 18) If there is still no pic-
ture, press the button again.
Ensure your cables are connected properly.
Use menus to adjust the contrast and brightness. (
page 55)
Check to see if the image is muted. (
page 29)
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (
page 70)
Enter your registered keyword if the SECURITY function is enabled. (
page 30)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the
power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or
power management software.
See also the next page.
Picture suddenly becomes
dark
When one of the following happens, the [LAMP MODE] automatically changes from [NORMAL] to [ECO].
* When there are no signals (blue or black screen) To return to the NORMAL mode, select another available
source.
* When the room where you' re presenting is particularly warm
Move the projector to a cooler location.
Color tone or hue is unusu-
al
Check if an appropriate color is selected in [WALL COLOR]. If not, select an appropriate option. (
page 61)
Adjust [HUE] in [ADJUST]
[BASIC]. ( page 55)
Image isn’t square to the
screen
Reposition the projector to improve its angle to the screen. (
page 20, 21)
Use the KEYSTONE correction function to correct the trapezoid distortion. (
page 25)
Picture is blurred Make sure that focus is appropriate.
Reposition the projector to improve its angle to the screen. (
page 20, 21)
Ensure that the distance between the projector and screen is within the adjustment range of the lens. (
page 10)
Make sure that the distance between the focus sensor and the screen is within the effective range of the AUTO
FOCUS. ( page 22)
Make sure that the requirements for the AUTO FOCUS are met. (
page 22)
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Flicker appears on screen • Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5000
feet/1500 meters or lower. Using the projector at altitudes less than approximately 5000 feet/1500 meters and setting
to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
(
page 65)
Image is scrolling verti-
cally, horizontally or both
Use the appropriate source button on the remote control to select your source. (
page 18)
Adjust the computer image manually with the [HORIZONTAL] and [VERTICAL] in [ADJUST]
[IMAGE OPTIONS]
in the menu. ( page 57)
Remote control does not
work
Install new batteries. (
page 8)
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. (
page 8)
Indicator is lit or blinking See the POWER/STATUS/LAMP Indicator. ( page 76)
Cross color in RGB mode Press the AUTO ADJ. button on the remote control (SELECT button on the projector cabinet). ( page 26)
Adjust the computer image manually with [CLOCK] and [PHASE] in [ADJUST]
[IMAGE OPTIONS] in the menu. (
page 56)
Formoreinformationcontactyourdealer.
86

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nec np61 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nec np61 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Nec np61

Nec np61 Gebruiksaanwijzing - Deutsch - 100 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info