493539
70
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
Portable Projector
VT676/VT670/VT575/VT470/VT47
Users Manual
i
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your NEC VT676/VT670/VT575/VT470/VT47 Projector and keep the
manual handy for future reference. Your serial number is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power outlet.
The power outlet socket should be installed as near to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this
unit has been provided.
The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS
CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST
BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.
DOC Compliance Notice (for Canada only)
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance-3. GSGV (for Germany only):
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
CAUTION
Avoid displaying stationary images for a prolonged period of time.
Doing so can result in these images being temporarily sustained on the surface of the LCD panel.
If this should happen, continue to use your projector. The static background from previous images will
disappear.
CAUTION
Do not put the projector on its side when the lamp is turned on.
Doing so may cause damage to the projector.
© NEC Viewtechnology, Ltd. 2004 - 2005
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. Wash hands after handling.
ii
Important Information
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those
specified by NEC Solutions (America), Inc. in this manual. Failure to comply with this government regulation could
void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with
this equipment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your projector carefully. Dropping or jarring can damage internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes.
d. Please consult your dealer for more information.
10˚
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other than
the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
iii
Important Information
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside
your projector. Allow at least 4 inches (10 cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.
Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as
a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately
and have the object removed by a qualified NEC service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage to your eyes could result.
5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the
lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can
cause unpredictable outcome such as fire or injury to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while the projector is on. Doing so can lead to
melting of the cap and possibly burning your hands due to the heat emitted from the light output.
7. Do not place any objects, which are easily affected by heat, in front of the projector lens or a projector exhaust
vent.
Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the
light output and exhaust.
8. The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power
supply fits this requirement before attempting to use your projector.
9. Handle the power cable carefully and avoid excessive bending.
A damaged cord can cause electric shock or fire.
10. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.
11. Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
12. Do not handle the power plug with wet hands.
CAUTION
Do not try to touch the ventilation outlet on the left side (when seen from the front) as it can become heated
while the projector is turned on.
Do no use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or
hanging on the wall can cause damage to the projector.
When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle
to the projector cabinet are tight. (VT676/VT670/VT470 only)
Insufficient tightening of the two screws could result in the projector falling and causing injury.
Do not send the projector in the soft carrying case by parcel delivery service or cargo shipment. The projector
inside the soft carrying case could be damaged.
Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[Advanced] [Fan Mode] [High].)
Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
* While the Hour Glass icon appears.
* While the cooling fans are running. (The cooling fans continue to work for 30 seconds after the projector is
turned off).
iv
Lamp Replacement
•To replace the lamp, follow all instructions provided on page 50.
Be sure to replace the lamp when the message “The lamp has reached the end of its usable life. Please
replace the lamp. appears. If you continue to use the lamp after the lamp has reached the end of its usable
life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
Allow a minimum of 30 seconds to elapse after turning off the projector. Then turn off the main power switch,
disconnect the power cable and allow 60 minutes to cool the projector before replacing the lamp.
Important Information
v
Table of Contents
Important Information ........................................................................... i
1. Introduction ......................................................................................1
What's in the Box? ........................................................................................................ 1
Introduction to the Projector ......................................................................................... 2
Part Names of the Projector ......................................................................................... 4
Attaching the Supplied Carrying Handle (VT676/VT670/VT470 only) .................... 5
Top Features ........................................................................................................... 6
Te r minal Panel Features ......................................................................................... 7
Part Names of the Remote Control .............................................................................. 8
Battery Installation ........................................................................................... 10
Remote Control Precautions ............................................................................ 10
Operating Range for Wireless Remote Control................................................ 10
2. Installation and Connections ....................................................... 11
Setting Up the Screen and the Projector .................................................................... 11
Selecting a Location.............................................................................................. 11
VT676/VT670/VT575/VT470 ........................................................................... 11
VT47 ................................................................................................................ 12
Throw Distance and Screen Size .......................................................................... 13
Making Connections ................................................................................................... 15
Enabling the computer’s external display .............................................................. 15
Connecting Your PC or Macintosh Computer........................................................ 15
To connect SCART output (RGB) ......................................................................... 16
Connecting an External Monitor ........................................................................... 17
Connecting Your DVD Player with Component Output .......................................... 18
Connecting Your VCR or Laser Disc Player .......................................................... 19
Connecting the Supplied Power Cable ................................................................. 20
3. Projecting an Image (Basic Operation)...................................... 21
Tur ning on the Projector ............................................................................................. 21
Note on Startup Screen (Menu Language Select screen) .................................... 22
Selecting a Source ..................................................................................................... 23
Adjusting the Picture Size and Position ...................................................................... 24
Correcting Keystone Distortion ................................................................................... 26
Optimizing RGB Picture Automatically ....................................................................... 28
Tur ning Up or Down Volume ....................................................................................... 28
Tur ning off the Projector ............................................................................................. 29
After Use..................................................................................................................... 29
vi
Table of Contents
4. Convenient Features ...................................................................... 30
Tur ning Off the Image and Sound............................................................................... 30
Freezing a Picture ...................................................................................................... 30
Enlarging and Moving a Picture.................................................................................. 30
Using the Remote Mouse Function (VT676/VT670/VT470 only) ............................... 31
5. Using On-Screen Menu ................................................................. 32
Using the Menus......................................................................................................... 32
Menu Elements........................................................................................................... 34
List of Menu Items ...................................................................................................... 35
Menu Descriptions & Functions [Picture].................................................................... 37
Menu Descriptions & Functions [Image] ..................................................................... 39
Menu Descriptions & Functions [Setup] ..................................................................... 40
Menu Descriptions & Functions [Advanced] ............................................................... 42
Menu Descriptions & Functions [Information] ............................................................. 46
Menu Descriptions & Functions [Default] ................................................................... 47
6. Maintenance .................................................................................... 48
Cleaning or Replacing the Filter ................................................................................ 48
Cleaning the Cabinet and the Lens ........................................................................... 49
Replacing the Lamp................................................................................................... 50
7. Appendix ........................................................................................... 53
Troubleshooting ......................................................................................................... 53
Specifications ............................................................................................................ 56
Cabinet Dimensions .................................................................................................. 58
VT676/VT670/VT575/VT470................................................................................. 58
VT47 ..................................................................................................................... 59
Pin Assignments of D-Sub COMPUTER Input Connector ........................................ 60
Compatible Input Signal List ...................................................................................... 61
PC Control Codes and Cable Connection ................................................................. 62
Optional Presentation Remote Control Kit (PR52KIT)............................................... 64
Troubleshooting Check List........................................................................................ 68
¾ TravelCare.................................................................................................................. 70
1
What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your projector.
ZOOM
F
O
C
U
S
SELE
CT
L
A
M
P
S
T
A
T
U
S
P
O
W
E
R
V
I
D
E
O
S
-
V
I
D
E
O
C
O
M
P
U
T
E
R
-
1
C
O
M
P
U
T
E
R
-
2
O
N
/
S
T
A
N
D
B
Y
A
U
T
O
A
D
J
.
Projector
Lens cap
(24F40111)
Power cable
(US: VT676/VT670/VT470: 7N080213)
(US: VT575/VT47: 7N080212)
(EU: VT676G/VT670G/VT470G: 7N080007)
(EU: VT575G/VT47G: 7N080005)
RGB/VGA signal cable
(7N520032)
Soft carrying case
(24BS7423)
Quick
Setup
Guide
Important
Information
CD-ROM
User’s manual
For North America only
Registration card
Limited warranty
For Europe only
Guarantee policy
Quick Setup Guide
Important Information
1. Introduction
For VT676, VT670 and VT470 only
V
O
L
U
M
E
S
-V
ID
E
O
V
ID
E
O
L
-C
L
IC
K
ENTER
E
X
I
T
M
E
N
U
U
P
M
A
G
N
I
F
Y
P
A
G
E
O
F
F
P
O
W
E
R
O
N
P
IC
-M
U
T
E
D
O
W
N
M
O
U
S
E
R-CLICK
A
U
T
O
A
D
J
.
C
O
M
P
U
T
E
R
A
S
P
E
C
T
H
E
L
P
F
R
E
E
Z
E
P
IC
T
U
R
E
1
2
Remote control
(7N900522)
Batteries (AAA
ן
2)
Remote mouse receiver
(7N900561)
Carrying handle (24F39671)
Screw (M4
ן
2: 24N07502)
Flathead screwdriver (24H51611)
2
1. Introduction
Introduction to the Projector
This section introduces you to your new VT676/VT670/VT575/VT470/VT47 Projector and describes the features and
controls.
Congratulations on Your Purchase of The VT676/VT670/VT575/VT470/VT47 Projector
The VT676/VT670/VT575/VT470/VT47 is one of the very best projectors available today. The VT676/VT670/VT575/
VT470/VT47 enables you to project precise images up to 300 inches across (measured diagonally) from your PC or
Macintosh computer (desktop or notebook), VCR, DVD player, document camera, or a laser disc player.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen,
and the projector can be permanently mounted on a ceiling*
1
. The remote control can be used wirelessly.
*
1
Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes. Please consult your dealer for more information.
Features you'll enjoy:
•Auto vertical keystone correction up to +/– 30 degrees
Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white
screen material
Quick Start & Quick Shutoff
The quick start & quick shutoff function means you can set up or put away the projector without delay.
Nine seconds after turning on the power, the projector is ready to display PC or video images.
When you're finished, the fans stop in 30 seconds after turning off the power, so you can put away the projector
quickly after the conference or class.
•Low level operation noise
Short focal length lens
130W lamp (110W Eco mode) : VT575/VT47
180W lamp (150W Eco mode) : VT670/VT470
190W lamp (150W Eco mode) : VT676
Direct keys for source selection
•New Color Management system
•New menu design improves operation
Safety protect by Security function
Security feature prevents the projector from being used by unauthorized individuals.
Keyword prevents unauthorized individuals from changing projector settings or adjustments.
NEC’s exclusive Advanced AccuBlend intelligent pixel blending technology - an extremely accurate image
compression technology - offers a crisp image with UXGA (1600ן1200) resolution*
2
Supports most IBM VGA, SVGA, XGA , SXGA/UXGA(with Advanced AccuBlend)*
2
, Macintosh, component
signal (YCbCr/ YPbPr) or any other RGB signals within a horizontal frequency range of 24 to 100 kHz and a
vertical frequency range of 50 to 120 Hz. This includes NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and
NTSC4.43 standard video signals.
*
2
A UXGA (1600ן1200) and SXGA image (1280ן1024) are displayed with NEC’s Advanced AccuBlend on
VT676, VT670 and VT575.
A UXGA (1600ן1200), SXGA (1280ן1024) and XGA (1024ן768) image are displayed with NEC’s Ad-
vanced AccuBlend on VT470.
An SXGA (1280ן1024) and XGA (1024ן768) images are displayed with NEC’s Advanced AccuBlend on
VT47.
3
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
•You can use the supplied wireless remote control and remote mouse receiver to operate your PC mouse
wireless from across the room. The remote mouse receiver supports almost any PC using a USB connection
(VT676, VT670 and VT470).
•You can control the projector with a PC or control system using the PC Control port.
The contemporary cabinet design is light, compact, easy to carry, and complements any office, boardroom or
auditorium.
About this user's manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to
review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find an
overview. If the section doesn't apply, you can skip it.
IBM is a trademark or registered trademark of International Business Machines Corporation.
Mac and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks
of Microsoft Corporation.
Other product and company names mentioned in this user’s manual may be the trademarks or registered
trademarks of their respective holders.
1. Introduction
4
1. Introduction
Part Names of the Projector
ZOOM
F
O
C
U
S
S
EL
EC
T
L
A
M
P
S
T
A
T
U
S
P
O
W
E
R
V
I
D
E
O
S
-
V
I
D
E
O
C
O
M
P
U
T
E
R
-1
C
O
M
P
U
T
E
R
-
2
O
N
/S
T
A
N
D
B
Y
A
U
T
O
A
D
J
.
AC IN
ZO
OM
F
OCU
S
SE
LEC
T
LAM
P
STAT
US
POW
ER
VIDEO
S-VIDEO
COM
PU
TER-1
COM
PUTER-2
O
N/STAND B
Y
AU
TO
ADJ.
AUDIO OUT
S-VIDEO IN
COMPUTER 1 IN
COMPUTER OUT
PC CONTROL
AUDIO
AUDIO
COMPUTER 2 IN
VIDEO IN
AUDIO
L/MONO
R
AUDIO
L/MONO
R
Zoom Lever (VT676/VT670/VT575/VT470)
Digital Zoom Button (VT47)
(See page 25)
Controls
(See page 6)
Lens
Lens Cap
Built-in Security Slot ( )*
Focus Ring
(See page 25)
Adjustable Tilt Foot Lever
(See page 24)
Adjustable Tilt Foot
(See page 24)
Remote sensor
(See page 10)
Ventilation (inlet) / Filter Cover
(See page 48)
Ventilation (inlet)
Front/Top
AC Input
Connect the supplied power cable's two-pin plug here, and
plug the other end into an active wall outlet. (See page 20)
Main Power Switch
When you plug the supplied power cable into an active wall outlet
and turn on the Main Power, the POWER indicator turns orange
and the projector is in standby mode.
(See page 21)
Remote sensor
(See page 10)
Ter minal Panel
(See page 7)
Monaural Speaker
(1W)
Rear
* This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
Ventilation (outlet)
Heated air is exhausted from here.
F
O
CU
S
ZO
O
M
5
1. Introduction
For VT676, VT670 and VT470 only
Attaching the supplied carrying handle
You can carry the projector by attaching the supplied carrying handle securely to the projector.
To attach the supplied carrying handle, use the supplied flathead screwdriver and two screws.
Place a soft cloth on the working surface before turning the projector over to prevent scratching the top cover.
Make sure that the carrying handle is attached with correct orientation as shown below.
Bottom
Adjustable Tilt Foot
(See page 24)
Adjustable Tilt Foot Lever
(See page 24)
Adjustable Tilt Foot Lever
(See page 24)
Lamp Cover
(See page 50)
CAUTION
When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle
to the projector cabinet are tight.
Carrying handle
Screw
Flathead screwdriver
6
1. Introduction
Top Features
LAMP
STATUS
POWER VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
AUTO
ADJ.
COMPUTER
ON/STAND BY
SELECT
12 13
10 2 3 411
1567
7
8
9
8
1. POWER Button (ON / STAND BY) ( )
Use this button to turn the power on and off when the
main power is supplied and the projector is in standby
mode.
To turn on the projector, press and hold this button for
a minimum of two seconds. To turn off the projector,
press this button twice.
2. POWER Indicator
When this indicator is green, the projector is on; when
this indicator is orange, it is in standby mode. See the
Power Indicator section on page 53 for more details.
3. STATUS Indicator
If this light blinks red rapidly, it indicates that an error
has occurred, the lamp cover is not attached properly
or the projector has overheated. If this light remains
orange, it indicates that you have pressed a cabinet
key while the Cabinet Button Lock is enabled. See the
Status Indicator section on page 53 for more details.
4. LAMP Indicator
If this light blinks red rapidly, it's warning you that the
lamp has reached the end of its usable life. After this
light appears, replace the lamp as soon as possible
(See page 50). If this is lit green continually, it indi-
cates that the lamp mode is set to Eco. See the Lamp
Indicator section on page 53 for more details.
5. VIDEO Button
Press this button to select a video source from a VCR,
DVD player, laser disc player or document camera.
6. S-VIDEO Button
Press this button to select an S-Video source from a
VCR, DVD player, laser disc player or document cam-
era.
7. COMPUTER1 and 2 Buttons (one COMPUTER
port on VT47) Button
Press this button to select an RGB source from com-
puter or component equipment connected to your
COMPUTER 1 or 2 port.
8. AUTO ADJ. Button
Use this button to adjust an RGB source for an opti-
mal picture (See page 28).
9. Source Indicators
When one of the COMPUTER, VIDEO or S-VIDEO
input is selected, the corresponding source indicator
lights.
10. MENU Button
Displays the menu.
11. SELECT ̆̄̇̈ / Volume Buttons
̆̄ : Use these buttons to select the menu of the
item you wish to adjust.
̇̈ : Use these buttons to change the level of a se-
lected menu item. A press of the ̈ button ex-
ecutes the selection. When no menus appear,
these buttons work as a volume control.
12. ENTER Button
Executes your menu selection and activates items
selected from the menu.
13. EXIT Button
Pressing this button will return to the previous menu.
While you are in the main menu, pressing this button
will close the menu.
VT47
VT676/VT670/VT575/VT470
7
1. Introduction
AUDIO OUT
AUDIO
S-VIDEO IN
COMPUTER 2 IN
VIDEO IN
COMPUTER 1 IN
MONITOR OUT
PC CONTROL
L/MONO
R
AUDIO
L/MONO
R
AUDIO
AUDIO
S-VIDEO IN
VIDEO IN
COMPUTER IN
MONITOR OUT
PC CONTROL
L/MONO
R
AUDIO
4 1
325
4 1
3 2 5
Te r minal Panel Features
1.
COMPUTER 1 and 2 IN / Component Input Connector
(Mini D-Sub 15 Pin) (One COMPUTER port on VT47)
Connect your computer or other analog RGB equip-
ment such as IBM compatible or Macintosh comput-
ers. Use the supplied RGB cable to connect to your
computer. This also serves as a component input con-
nector that allows you to connect a component video
output of component equipment such as a DVD player.
This connector also supports SCART output signal.
See page 16 for more details.
COMPUTER AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your
computer or DVD player when connected to the COM-
PUTER input. A commercially available audio cable is
required.
2.
MONITOR OUT Connector (Mini D-Sub 15 Pin)
You can use this connector to loop your computer
image to an external monitor from the RGB input
source.
This connector outputs RGB signal in standby mode.
AUDIO OUT Mini Jack (Stereo Mini)
(Not available on VT47)
You can use this jack to output sound from the cur-
rently selected source (COMPUTER, VIDEO or S-
VIDEO). Output sound level can be adjusted in accor-
dance with the sound level of the internal speaker.
Note that this cannot be used as a headphone jack.
(When audio equipment is connected, the projector
speaker is disabled.)
When a cable mini-plug is inserted into this jack, both
the right and left audio signals are not mixed, but sepa-
rate.
For example, when a cable mini-plug is inserted into
the left AUDIO IN jack only, only left sound is output.
3. S-VIDEO IN Connector (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an
external source like a VCR.
NOTE: S-Video provides more vivid color and higher
resolution than the traditional composite video format.
S-VIDEO AUDIO Input Jacks L/R (RCA)
These are your left and right channel audio inputs for
stereo sound from an S-Video source.
4. VIDEO IN Connector (RCA)
Connect a VCR, DVD player, laser disc player, or docu-
ment camera here to project video.
VIDEO AUDIO Input Jacks L/R (RCA)
These are your left and right channel audio inputs for
stereo sound from a Video source.
NOTE: The VIDEO AUDIO inputs can also be used as S-
VIDEO AUDIO inputs on VT47.
5. PC CONTROL Port (DIN 8 Pin)
Use this port to connect a PC or control system. This
enables you to control the projector using serial com-
munication protocol. If you are writing your own pro-
gram, typical PC control codes are on page 62.
VT47
VT676/VT670/VT575/VT470
8
1. Introduction
Part Names of the Remote Control
NOTE: If you are using a Macintosh computer, you can click
either the MOUSE R-CLICK or MOUSE L-CLICK button to
activate the mouse. (VT676/VT670/VT470 only)
1. Infrared Transmitter
Direct the remote control toward the remote sensor
on the projector cabinet.
2. POWER ON Button
When the main power is on, you can use this button
to turn your projector on.
NOTE: To turn on the projector, press and hold the POWER
ON button for a minimum of two seconds.
3. POWER OFF Button
You can use this button to turn your projector off.
NOTE: To turn off the projector, press the POWER OFF
button twice.
4. MAGNIFY (+)(–) Button
Use this button to adjust the image size up to 400%.
The image is magnified about the center of the screen.
See page 30.
VOLUME
S-VIDEO
VIDEO
L-CLICK
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
MOUSE
R-CLICK
AUTO ADJ.COMPUTER
ASPECT HELP
FREEZEPICTURE
1
2
1
3
4
7
6
9
2
8
10
11
13
14
12
20
21
19
16
15
18
5
17
5. PIC-MUTE Button
This button turns off the image and sound for a short
period of time. Press again to restore the image and
sound.
6. PAGE UP/DOWN Button
(Not available on VT575 and VT47)
Use these buttons to operate your computer with the
supplied remote mouse receiver. See page 31. You
can use these buttons to scroll the viewing area of the
window or to move to the previous or next slide in
PowerPoint on your computer.
7. MENU Button
Displays the menu for various settings and adjust-
ments.
8. SELECT ̆̄̇̈ (Mouse) Button
̆̄ : Use these buttons to select the menu of the
item you wish to adjust.
̇̈ : Use these buttons to change the level of a se-
lected menu item. A press of the ̈ button ex-
ecutes the selection.
When an image is magnified, the SELECT ̆̄̇̈
button moves the image. See page 30.
9. ENTER Button
Use this button to enter your menu selection. It works
the same way as the ENTER button on the cabinet.
See page 6.
10. EXIT Button
It works the same way as the EXIT button on the cabi-
net. See page 6.
11. MOUSE L-CLICK Button
(Not available on VT575 and VT47)
This button works as the mouse left button when the
supplied remote mouse receiver is connected with your
computer. See page 31.
12. MOUSE R-CLICK Button
(Not available on VT575 and VT47)
This button works as the mouse right button when the
supplied remote mouse receiver is connected with your
computer. See page 31.
13. VIDEO Button
Press this button to select a video source from a VCR,
DVD player, laser disc player or document camera.
14. S-VIDEO Button
Press this button to select an S-Video source from a
VCR.
9
15. COMPUTER 1/2 Button
Press this button to select COMPUTER 1 or 2 (or Com-
ponent) input. (One COMPUTER port on VT47)
16. AUTO ADJ. Button
Use this button to adjust an RGB source for an opti-
mal picture.
See page 28.
17. VOLUME (+)(–) Button
Press (+) to increase the volume and (–) to decrease
it.
18. ASPECT Button
Press this button once to display the Aspect Ratio
select menu. Keep pressing will change aspect ratios.
See page 39.
19. PICTURE Button
Press this button to display the Picture adjustment
menu to adjust Wall Color, Picture Management,
Brightness, Contrast, Sharpness, Color and Hue. See
pages 37 to 38.
VOLUME
S-VIDEO
VIDEO
L-CLICK
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
MOUSE
R-CLICK
AUTO ADJ.COMPUTER
ASPECT HELP
FREEZEPICTURE
1
2
1
3
4
7
6
9
2
8
10
11
13
14
12
20
21
19
16
15
18
5
17
1. Introduction
20. HELP Button
Provides the information on the current signal and pro-
jector settings. See page 46.
21. FREEZE Button
This button will freeze a picture. Press again to re-
sume motion.
10
1. Introduction
30°
30°
30°
30°
Remote Control Precautions
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
If you will not be using the remote control for a long time, remove the batteries.
Do not place the batteries upside down.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
Operating Range for Wireless Remote Control
Battery Installation
1
Press firmly and slide the
battery cover off.
2
Remove both old batteries and
install new ones (AAA). Ensure
that you have the batteries' po-
larity (+/–) aligned correctly.
3
Slip the cover back over the bat-
teries until it snaps into place. Do
not mix different types of batter-
ies or new and old batteries.
Remote sensor on projector cabinet
Remote control
7m/22 feet
7m/22 feet
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of
the remote sensor on the projector cabinet.
The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
11
This section describes how to set up your projector and how to connect video and audio sources.
2. Installation and Connections
Setting Up the Screen and the Projector
Selecting a Location (VT676/VT670/VT575/VT470)
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 21" (0.53 m) measured diagonally when the projector is roughly 29 inches (0.73 m) from the wall or
screen. The largest the image can be is 300" (7.6 m) when the projector is about 393 inches (10 m) from the wall or
screen. Use the drawing below as a guide.
Your projector is simple to set up and use.
But before you get started, you must first:
z Set up a screen and the projector.
x Connect your computer or video equip-
ment to the projector. See pages 15 to
19.
c Connect the supplied power cable. See
page 20.
NOTE: Ensure that the power cable and any
other cables are disconnected before moving
the projector. When moving the projector or
when it is not in use, cover the lens with the
lens cap.
To the wall outlet.
300"
240
"
200
"
180"
150"
120"
100"
60"
40"
30"
21"
80"
Distance (Unit: m/inch)
Screen Size (Unit: cm/inch)
Screen Size
Lens center
609.6(W)ן457.2(H) / 240(W)ן180(H)
487.7(W)ן365.8(H) / 192(W)ן144(H)
406.4(W)ן304.8(H) / 160(W)ן120(H)
365.8(W)ן274.3(H) / 144(W)ן108(H)
304.8(W)ן228.6(H) / 120(W)ן90(H)
243.8(W)ן182.9(H) / 96(W)ן72(H)
203.2(W)ן152.4(H) / 80(W)ן60(H)
162.6(W)ן121.9(H) / 64(W)ן48(H)
121.9(W)ן91.4(H) / 48(W)ן36(H)
81.3(W)ן61.0(H) / 32(W)ן24(H)
61.0(W)ן45.7(H) / 24(W)ן18(H)
42.7(W)ן32(H) / 17(W)ן13(H)
1.0/38
0.7/
29
2.0/78
2.6/104
3.3/130
4.0/157
5.0/196
6.0/236
6.6/262
8.0/314
10.0/393
A
C
I
N
1.3/
51
3
2
1
12
2. Installation and Connections
Selecting a Location (VT47)
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 25" (0.64 m) measured diagonally when the projector is roughly 23 inches (0.6 m) from the wall or
screen. The largest the image can be is 300" (7.6 m) when the projector is about 287 inches (7.3 m) from the wall or
screen. Use the drawing below as a guide.
25"
300
"
240
"
200
"
180
"
150
"
120
"
100
"
60
"
40
"
80
"
Distance (Unit: m/inch)
Lens center
0.6/
23
1.0/37
1.4/56
1.9/76
2.4/95
2.9/114
3.6/143
4.4/172
4.9/191
5.8/229
7.3/287
Screen Size (Unit: cm/inch)
Screen Size
609.6(W)ן457.2(H) / 240(W)ן180(H)
487.7(W)ן365.8(H) / 192(W)ן144(H)
406.4(W)ן304.8(H) / 160(W)ן120(H)
365.8(W)ן274.3(H) / 144(W)ן108(H)
304.8(W)ן228.6(H) / 120(W)ן90(H)
243.8(W)ן182.9(H) / 96(W)ן72(H)
203.2(W)ן152.4(H) / 80(W)ן60(H)
162.6(W)ן121.9(H) / 64(W)ן48(H)
121.9(W)ן91.4(H) / 48(W)ן36(H)
81.3(W)ן61.0(H) / 32(W)ן24(H)
50.8(W)ן38.1(H) / 20(W)ן15(H)
AC
I
N
NOTE: Digital Zoom can cause result in a blurry image because zooming is made electronically.
13
2. Installation and Connections
Lens Center
Throw Angle (Ͱ)
Throw Distance (C)
Screen center
Screen Diagonal
Screen Width
Screen Height
Screen Bottom
(B)
(D)
A
C
I
N
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the
position of installation.
Distance Chart
B =Vertical distance between lens center and
screen center
C = Throw distance
D =Vertical distance between lens center and
bottom of screen (top of screen for ceiling
application)
α = Throw angle
NOTE: Distances may vary +/-5%.
α
Wide – Tele
degree
–– 9.9
12.0 9.8
11.9 9.8
11.7 9.7
11.6 9.6
11.6 9.6
11.6 9.6
11.6 9.6
11.5 9.6
11.5 9.6
11.5 9.5
11.5 9.5
11.5 9.5
11.5 9.5
11.5 9.5
11.5 9.5
11.4 9.5
11.4 9.5
inch
13
15
18
24
36
43
48
50
54
60
72
90
108
120
126
144
162
180
Screen Size B C
Wide – Tele
D
Diagonal Width Height
inch
–– 29
28 34
34 42
46 56
70 85
84 102
93 113
98 119
105 128
117 142
141 171
176 214
212 257
236 285
247 300
283 343
319 386
354 429
inch
-1
-2
-2
-2
-4
-4
-5
-5
-6
-6
-7
-9
-11
-12
-13
-15
-17
-18
inch
5
6
7
10
14
17
19
20
22
24
29
36
43
48
50
57
65
72
inch
21
25
30
40
60
72
80
84
90
100
120
150
180
200
210
240
270
300
inch
17
20
24
32
48
58
64
67
72
80
96
120
144
160
168
192
216
240
α
Wide – Tele
degree
–– 9.9
12.0 9.8
11.9 9.8
11.7 9.7
11.6 9.6
11.6 9.6
11.6 9.6
11.6 9.6
11.5 9.6
11.5 9.6
11.5 9.5
11.5 9.5
11.5 9.5
11.5 9.5
11.5 9.5
11.5 9.5
11.4 9.5
11.4 9.5
mm
320
381
457
610
914
1097
1219
1280
1372
1524
1829
2286
2743
3048
3200
3658
4115
4572
Screen Size B C
Wide – Tele
D
Diagonal Width Height
mm
––– 730
720 870
870 1060
1170 1420
1770 2150
2130 2590
2370 2880
2490 3020
2670 3240
2970 3600
3580 4330
4480 5420
5380 6520
5980 7240
6280 7610
7190 8700
8090 9790
8990 10880
mm
-30
-40
-50
-60
-90
-110
-120
-130
-140
-160
-190
-230
-280
-310
-330
-370
-420
-470
mm
130
150
180
240
360
440
490
510
550
610
730
910
1090
1210
1270
1460
1640
1820
mm
533
635
762
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620
mm
427
508
610
813
1219
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096
α
inch
15
18
24
36
43
48
50
54
60
72
90
108
120
126
144
162
180
Screen Size
BD
Diagonal Width Height
inch
-2
-2
-2
-4
-4
-5
-5
-6
-6
-7
-9
-11
-12
-13
-15
-17
-18
inch
6
7
10
14
17
19
20
22
24
29
36
43
48
50
57
65
72
inch
25
30
40
60
72
80
84
90
100
120
150
180
200
210
240
270
300
inch
20
24
32
48
58
64
67
72
80
96
120
144
160
168
192
216
240
C
inch
23
28
37
56
68
76
80
85
95
114
143
172
191
201
229
258
287
degree
14.6
14.5
14.4
14.2
14.2
14.2
14.2
14.1
14.1
14.1
14.1
14.1
14.0
14.0
14.0
14.0
14.0
α
mm
381
457
610
914
1097
1219
1280
1372
1524
1829
2286
2743
3048
3200
3658
4115
4572
Screen Size
BD
Diagonal Width Height
mm
-40
-50
-60
-90
-110
-120
-130
-140
-160
-190
-230
-280
-310
-330
-370
-420
-470
mm
150
180
240
360
440
490
510
550
610
730
910
1090
1210
1270
1460
1640
1820
mm
635
762
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620
mm
508
610
813
1219
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096
C
mm
580
700
950
1440
1730
1920
2020
2170
2410
2900
3630
4360
4850
5100
5830
6560
7290
degree
14.6
14.5
14.4
14.2
14.2
14.2
14.2
14.1
14.1
14.1
14.1
14.1
14.0
14.0
14.0
14.0
14.0
VT47
VT676/VT670/VT575/VT470
14
2. Installation and Connections
WARNING
* Installing your projector on the ceiling must be done
by a qualified technician. Contact your NEC dealer for
more information.
* Do not attempt to install the projector yourself.
Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 41˚F (5˚C) and 95˚F (35˚C).
Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.
Ensure that you have adequate ventilation around your
projector so heat can dissipate. Do not cover the vents
on the side or the front of the projector.
Reflecting the Image
Using a mirror to reflect your projector's image enables
you to enjoy a much larger image. Contact your NEC
dealer if you need a mirror system. If you're using a mir-
ror system and your image is inverted, use the MENU
and SELECT buttons on your projector cabinet or your
remote control to correct the orientation. See page 41.
15
2. Installation and Connections
Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the
power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after
connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power
management software.
AC IN
AUDIO OUT
MONITOR OUT
PC CONTROL
AUDIO
S-VIDEO IN
COMPUTER 2 IN
VIDEO IN
COMPUTER 1 IN
AUDIO
L/MONO
R
AUDIO
L/MONO
R
COMPUTER 1 IN
AUDIO
COMPUTER 2 IN
AUDIO
S-VIDEO IN
VIDEO IN
COMPUTER IN
MONITOR OUT
PC CONTROL
L/MONO
R
PHONE
PHONE
COMPUTER IN
AUDIO
Connecting Your PC or Macintosh Computer
RGB/VGA signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It
is recommended that you use a commercially
available distribution amplifier if connecting a
signal cable longer than the supplied one.
Audio cable
(not supplied)
IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type)
NOTE: For older Macintosh, use a
commercially available pin adapter
(not supplied) to connect to your
Mac's video port.
IBM VGA or Compatibles (Notebook
type) or Macintosh (Notebook type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image
for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied RGB/VGA signal cable to connect your PC or Macintosh to the projector.
3. Connect the supplied power cable. See page 20.
4. Turn on the projector and the computer.
5. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer
you've connected to the projector.
NOTE: • VT676/VT670/VT575/VT470: The COMPUTER 1 connector supports Plug & Play (DDC2).
• VT47: The COMPUTER connector supports Plug & Play (DDC2).
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.
VT47
VT676/VT670/VT575/VT470
16
NOTE: The projector is not compatible with video decoded outputs of either the NEC ISS-6020 and ISS-6010 switchers.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the projector cabinet.
2. Installation and Connections
AC IN
AUDIO OUT
MONITOR OUT
PC CONTROL
AUDIO
S-VIDEO IN
COMPUTER 2 IN
VIDEO IN
COMPUTER 1 IN
AUDIO
L/MONO
R
AUDIO
L/MONO
R
COMPUTER 1 IN
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re-
quired for this connection.
NOTE: Audio signal is not available for this connection.
1. Turn off the power to the projector and your video equipment.
2. Use the NEC ADP-SC1 SCART adapter and a commercially available SCART cable to connect the RGB input of
your projector and a SCART output (RGB) of your video equipment.
3. Connect the supplied power cable. See page 20.
4. Turn on the power to the projector and your video equipment.
5. Use the COMPUTER 1 button on the projector cabinet to select the COMPUTER 1 input.
Use the COMPUTER button on the projector cabinet to select the COMPUTER input on VT47.
6. Press the MENU button on the projector cabinet to display the menu.
7. From the menu, select [Advanced] [Signal Select] [Computer 1 ([Computer] on VT47)] [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as
Euro-connector.
NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Europe. Contact your NEC dealer in Europe for more
information.
To connect SCART output (RGB)
Video equipment such as DVD player
Commercially available SCART cable
Female
ADP-SC1
Projector
To COMPUTER 1 input
(COMPUTER input on VT47)
17
2. Installation and Connections
Connecting an External Monitor
MONITOR OUT
AUDIO
AC IN
AUDIO OUT
MONITOR OUT
PC CONTROL
AUDIO
S-VIDEO IN
COMPUTER 2 IN
VIDEO IN
COMPUTER 1 IN
AUDIO
L/MONO
R
AUDIO
L/MONO
R
MONITOR OUT
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
image you're projecting.
To do so:
1. Turn off the power to your projector, monitor and computer.
2.
Use an RGB/VGA cable to connect your monitor to the MONITOR OUT (Mini D-Sub 15 pin) connector on your projector.
3. Connect the supplied power cable. See page 20.
4. Turn on the projector, monitor and the computer.
NOTE: Daisy chain connection is not possible.
RGB/VGA signal cable (supplied)
RGB/VGA signal cable (not supplied)
18
AUDIO IN
LR
AUDIO OUT
L R
Component
YCbCr
AC IN
AUDIO OUT
MONITOR OUT
PC CONTROL
AUDIO
S-VIDEO IN
COMPUTER 2 IN
VIDEO IN
COMPUTER 1 IN
AUDIO
L/MONO
R
AUDIO
L/MONO
R
COMPUTER 1 IN
AUDIO
AUDIO
S-VIDEO IN
VIDEO IN
COMPUTER IN
MONITOR OUT
PC CONTROL
L/MONO
R
COMPUTER IN
AUDIO
2. Installation and Connections
You can connect your projector to a DVD player with component output or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a commercially available component video cable
(RCAן3) and the optional 15-pin-to-RCA (female)ן3 cable to connect your DVD player to the COMPUTER IN
connector on the projector.
For a DVD player without component video (Y,Cb,Cr) output, use common RCA cables (not provided) to connect a
composite VIDEO output of the DVD player to the Video Input of the projector.
3. Connect the supplied power cable. See page 20.
4. Turn on the projector and DVD player.
A component signal will be automatically displayed. If not, from the menu, select [Advanced] [Signal Select]
[Computer], and then place a check mark in the Component radio button.
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.
Connecting Your DVD Player with Component Output
DVD player
Audio Equipment
Audio cable (not supplied)
Optional 15-pin - to - RCA (female)
ן
3 cable (ADP-CV1)
Component video RCA
ן
3
cable (not supplied)
VT47
VT676/VT670/VT575/VT470
19
2. Installation and Connections
AUDIO IN
LR
AUDIO OUT
L R
VIDEO OUT
S-VIDEOVIDEO
AC IN
AUDIO OUT
MONITOR OUT
PC CONTROL
AUDIO
S-VIDEO IN
COMPUTER 2 IN
VIDEO IN
COMPUTER 1 IN
AUDIO
L/MONO
R
AUDIO
L/MONO
R
S-VIDEO IN
VIDEO IN
AUDIO
AUDIO
Connecting Your VCR or Laser Disc Player
S-Video cable (not supplied)
Video cable (not supplied)
VCR/ Laser disc player
Audio equipment
Audio cable (not supplied)
Use an RCA or S-Video cable (not provided) to connect the video and use RCA cables (not provided) to connect
the audio from your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of an RCA cable to the video output (or one end of an S-Video cable to the S-Video output
connector) on the back of your VCR or laser disc player, connect the other end to the appropriate video input
on your projector. Connect one end of a pair RCA cables (not supplied) to the audio output on the back of your
VCR or laser disc player, connect the other end to your audio equipment or to the appropriate audio input on
the projector.
Be careful to keep the right and left channel connections correct for stereo sound.
NOTE: The AUDIO IN L/MONO and R jacks (RCA) are shared between the Video and S-Video inputs on VT47.
3. Connect the supplied power cable. See page 20.
4. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output
requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter.
20
2. Installation and Connections
A
C
IN
ZOOM
F
O
CU
S
SE
LECT
L
A
M
P
S
T
A
T
U
S
P
O
W
E
R
V
ID
E
O
S
-V
ID
E
OCO
M
P
U
T
E
R
-1
C
O
M
P
U
T
E
R
-2
O
N
/S
TA
N
D
B
Y
AUTO
ADJ.
AUDIO OUT
S-VIDEO IN
COMPUTER 1 IN
COMPUTER OUT
PC CONTROL
AUDIO AUDIO
COMPUTER 2 IN
VIDEO IN
AUDIO
L/M
ONO
R
AUDIO
L/MO
NO
R
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's two-pin plug to the AC IN of the projector, and then connect the other plug of
the supplied power cable in the wall outlet.
Make sure that the prongs are fully inserted into
both the AC IN and the wall outlet.
To wall outlet
CAUTION:
Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
While the Hour Glass icon appears.
While the cooling fans are running. The cooling fans continue to work for 30 seconds after the projector is
turned off.
21
3.
Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
Turning on the Projector
NOTE:
The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button (POWER ON and OFF on the
remote control).
When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (
)
position. Failure to do so may cause damage to the projector.
A
C
I
N
Z
O
O
M
F
O
C
U
S
STATUS
LAMP
POWER
1. To turn on the main power to the projector, press the
Main Power switch to the on position ( I ).
The POWER indicator will light orange.
See the Power Indicator section on page 53 for more
details.
2. Press the POWER (ON/STAND BY) button on the
projector cabinet or the POWER ON button on the
remote control for a minimum of 2 seconds. The
POWER indicator will turn to green and the projector
will become ready to use.
After you turn on your projector, ensure that the
computer or video source is turned on and that your
lens cap is removed.
NOTE: When no signal is available, a blue, black or logo screen is
displayed.
When the projector displays a blue or a black screen (not logo),
the Eco mode will be automatically selected in "Lamp Mode."
NOTE: If you turn on the projector immediately after the lamp is
turned off or when the temperature is high, the fans runs without
displaying an image for some time and then the projector will
display the image.
LAMP
STATUS
POWER VIDEO S-VIDEO
ON/STAND BY
SELECT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
POWER
POWER POWER
STATUS
LAMP
STATUS
LAMP
STATUS
LAMP
Standby Blinking Power On
Steady orange light Blinking green
light
Steady green
light
See page 53 for more details.
22
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 8 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT
̆
or
̄
button to select one of the 8
languages for the menu.
LAMP
STATUS
POWER VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
SELECT
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu opera-
tion.
If you want, you can select the menu language later. See "Lan-
guage" on pages 35 and 41.
LAMP
STATUS
POWER VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
SELECT
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp
lighting is stabilized.
When the Lamp mode is set to Eco, the LAMP indicator will light green.
If one of the following things happens, the projector will not turn on.
If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal
components to cool down.
When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and
then turn on the power.
23
3. Projecting an Image (Basic Operation)
Selecting a Source
Selecting the computer or video source
VIDEO S-VIDEO COMPUTER-1 COMPUTER-2
LAMP
STATUS
POWER
AUTO
ADJ.
ON/STAND BY
SELECT
VOLUME
L-CLICK
MOUSE
R-CLICK
AUTO ADJ.
ASPECT HELP
FREEZEPICTURE
S-VIDEO
VIDEO
COMPUTER
1
2
NOTE: Turn on the computer or VCR connected to the projector.
Using the cabinet buttons
Press any one of the COMPUTER 1/2 (COMPUTER button on VT47),
VIDEO and S-VIDEO buttons.
The corresponding indicator will light green.
Using the Remote Control
Press any one of the COMPUTER 1/2, VIDEO or S-VIDEO buttons.
(One COMPUTER port on VT47)
24
3. Projecting an Image (Basic Operation)
Place your projector on a flat level surface and ensure that the projector is
square to the screen.
Lift the front edge of the projector to center the image vertically.
* If the projected image does not appear square to the screen then use the
Keystone feature for proper adjustment. See page 26.
Adjusting the Picture Size and Position
A
C
I
N
Z
OOM
F
O
CU
S
AC
I
N
Z
O
O
M
F
OC
U
S
Adjust the Tilt Foot
1. Lift the front edge of the projector.
2. Push up the Adjustable Tilt Foot Levers on the right and left sides
of the projector to extend the adjustable tilt feet (maximum height).
3. Push down the Adjustable Tilt Foot Levers.
4. Lower the front of the projector to the desired height and release
the Adjustable Tilt Foot Lever to lock the Adjustable tilt foot. There
is approximately 10 degrees of up and down adjustment for the
front of the projector.
CAUTION
Do not use the tilt-foot for purposes other than originally intended. Misuses
such as gripping the tilt-foot or hanging on the wall can cause damage to the
projector.
2
Z
O
O
M
F
O
C
U
S
S
E
L
E
C
T
L
A
M
P
S
T
A
T
U
S
P
O
W
E
R
V
ID
E
O
S
-
V
I
D
E
O
C
O
M
P
U
T
E
R
-
1
C
O
M
P
U
T
E
R
-
2
O
N
/
S
T
A
N
D
B
Y
AUTO
ADJ.
1
2
ZOOM
F
O
CU
S
SELECT
LAMP
STATUS
POWER VIDEO
S-VIDEO
COM
PUTER-1
C
OMPU
TER-2
ON/STAND BY
A
U
T
O
A
D
J
.
3
4
4
Adjustable Tilt Foot
Move the projector left to center the image horizontally on the screen.
Adjustable Tilt
Foot Lever
Adjustable Tilt
Foot Lever
25
3. Projecting an Image (Basic Operation)
A
C
I
N
Z
O
O
M
F
O
C
U
S
ZOOM
F
O
C
U
S
F
O
C
U
S
ZOOM
A
C
I
N
Z
O
O
M
F
O
C
U
S
F
O
C
U
S
Focus
Use the FOCUS ring to obtain the best focus.
Zoom
VT676/VT670/VT575/VT470
Use the ZOOM lever to finely adjust the image size on the
screen.
VT47
Use the Digital ZOOM button on the projector cabinet to
electronically enlarge or reduce the image size.
NOTE: Digital Zoom can cause result in a blurry image because
zooming is made electronically.
VT47
VT676/VT670/VT575/VT470
26
Correcting Keystone Distortion
Auto Keystone Correction
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
Note that the vertical keystone angle can be corrected between 30 degrees upward and 30 degrees downward of
projector tilt from level.
3. Projecting an Image (Basic Operation)
NOTE: Auto and Manual Keystone correction angle could be less than 30 degrees depending on some kinds of signal and aspect
ratios.
NOTE: The Auto Keystone Correction feature can cause an image to be slightly blurred because the correction is made electroni-
cally.
Manual Keystone Correction
You can also correct the vertical keystone distor-
tion manually.
To do so:
1. Press the MENU button.
The menu will be displayed.
2. Turn off the Auto Keystone function.
Use the SELECT
̄
button to select
“Image” and then press the SELECT
̈
button. The “Auto Keystone” will be
displayed. Press the SELECT
̈
to select
“Off”.
3. Select the Keystone function.
Use the SELECT
̄
button to select
“Keystone”.
4. Correct the vertical distortion.
Use the SELECT
̇
or
̈
button to correct
the vertical keystone distortion.
NOTE: The Keystone Correction feature can cause
an image to be slightly blurred because the
correction is made electronically.
27
3. Projecting an Image (Basic Operation)
5. Press the MENU button to close the menu.
NOTE: You can save the changes using the Keystone Save
feature when you turn off the projector. See page 39.
28
3. Projecting an Image (Basic Operation)
Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the AUTO ADJ. button to optimize an RGB image automatically.
[Poor picture]
[Normal picture]
VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
VOLUME
S-VIDEO
VIDEO
L-CLICK
MOUSE
R-CLICK
AUTO ADJ.COMPUTER
ASPECT HELP
FREEZEPICTURE
1
2
Press the AUTO ADJ. button to fine-tune the computer image or to remove any vertical banding that might appear and
to reduce video noise, dot interference or cross talk (this is evident when part of your image appears to be shimmer-
ing). This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This function also
adjusts the clock phase to reduce video noise, dot interference or cross talk. (This is evident when part of your image
appears to be shimmering.)
This adjustment may be necessary when you connect your computer for the first time.
NOTE:
Some signals may not be displayed correctly or take time.
The Auto Adjust function does not work for component and video signal.
If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Horizontal/Vertical Position Clock and Phase
manually. See pages 45 and 46.
Turning Up or Down Volume
Increase volume
Decrease volume
VOLUME
S-VIDEO
VIDEO
L-CLICK
MOUSE
R-CLICK
AUTO ADJ.COMPUTER
ASPECT HELP
FREEZEPICTURE
1
2
Sound level from the speaker and the AU-
DIO OUT jack (Stereo mini) on the projec-
tor can be adjusted.
VIDEO S-VIDEO
AUTO
ADJ.
COMPUTER
VT47
VT676/VT670/VT575/VT470
29
Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
LAMP
STATUS
POWER VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
SELECT
L-CLICK
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
R-CLICK
First, press the POWER (ON/STAND BY) button on the
projector cabinet or the POWER OFF button on the re-
mote control. The “Power Off / Are you sure?” message
will appear.
CAUTION
Do not unplug the power cable from the wall outlet or do not turn off
the main power under any one of the following circumstances. Doing
so can cause damage to the projector:
While the Hour Glass icon appears.
While the cooling fans are running. (The cooling fans continue to
work for 30 seconds after the projector is turned off)
A
C
IN
Z
O
O
M
F
O
C
U
S
After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt feet if extended.
4. Cover the lens with the lens cap.
5. Put the projector and its accessories in the supplied soft carrying case.
Secondly, press the ENTER button or press the POWER
(ON/STAND BY) or the POWER OFF button again.
The power indicator will glow orange. After the projector
turns off, the cooling fans keep operating for 30 seconds
(Cooling-off time).
Immediately after turning on the projector and displaying
an image, you cannot turn off the projector for 60 sec-
onds.
Finally, turn off the Main Power switch. The power indica-
tor will go out.
POWER
STATUS
LAMP
POWER
POWER
STATUS
LAMP
STATUS
LAMP
Power On Fan running Standby
Steady green light Blinking
orange light
Steady orange
light
30
4. Convenient Features
³ Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
· Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume
motion.
Enlarging and Moving a Picture
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
You can enlarge the picture up to 400 percent.
To do so:
1. Press the MAGNIFY (+) button to magnify the picture.
To move the magnified image, use the SELECT button.
2. Return the image to the original size.
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
VOLUME
S-VIDEO
ASPECT HELP
FREEZEPICTURE
1
2
31
4. Convenient Features
Using Remote Mouse Receiver (VT676/VT670/VT470 only)
The remote mouse receiver enables you to operate your computer’s mouse functions from the remote control. It is a
great convenience for clicking through your computer-generated presentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change
your computer settings.
30˚
30˚
Remote mouse receiver
Computer
To USB port of PC or Macintosh
When operating a computer via the remote mouse receiver
Remote sensor on the
remote mouse receiver
7m/22 feet
When connecting using the USB terminal
For PC, the mouse receiver can only be used with a Windows 98/Me/XP* or Windows 2000 operating system.
* NOTE: In Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may
not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.
Operating your computer’s mouse from the remote control
You can operate your computer's mouse from the remote control.
PAGE UP/DOWN Button: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint
on your computer.
̆̄̇̈ / Mouse Buttons: moves the mouse cursor on your computer.
MOUSE L-CLICK Button: works as the mouse left button.
MOUSE R-CLICK Button: works as the mouse right button.
32
Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.
1. Press the MENU button on the remote control or projector cabinet to display the Menu.
5. Using On-Screen Menu
ENTER
EXIT
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
MENU
2. Press the SELECT
̆
or
̄
button on the remote control or the projector cabinet to highlight the menu for
the item you want to adjust or set.
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
3. Press the SELECT
̈
button or the ENTER button on the remote control or the projector cabinet to select
a submenu or item.
33
5. Using On-Screen Menu
4. Use the SELECT
̆
or
̄
button on the remote control or the projector cabinet to select the item you want
to adjust or set.
5. Adjust the level or turn the selected item on or off by using
SELECT
̇
or
̈
button on the remote control or the projector
cabinet.
The on-screen slide bar will show you the amount of increase
or decrease.
Changes are stored until you adjust it again.
EXIT ...................... Return to the previous menu.
6. Repeat steps 2-5 to adjust an additional item, or press the
MENU button to close the menu.
ENTER
EXIT
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
MENU
ENTER
EXIT
MENU
UP
MAGNIFY PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
34
5. Using On-Screen Menu
· Menu Elements
Highlight
Title
Slide bar
Off Timer remaining
time
Source
Radio button
Solid triangle
Check mark
Ta b
Thermometer symbol
Key symbol
Menu windows or dialog boxes typically have the following elements:
Title .......................................... Indicates the menu title.
Highlight................................... Indicates the selected menu or item.
Source ...................................... Indicates the currently selected source.
Remaining countdown time ..... Indicates the remaining countdown time when the Off Timer is preset.
Solid triangle ............................ Indicates further choices are available. A highlighted triangle indicates the item is active.
Tab ........................................... Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button ............................ Use this round button to select an option in a dialog box.
Check mark .............................. Indicates the item is selected.
Slide bar ................................... Indicates settings or the direction of adjustment.
Key symbol .............................. Indicates the Cabinet Button Lock is enabled.
Thermometer symbol ............... Indicates the lamp mode is forcibly set to Eco mode because the internal temperature is too
high.
35
» List of Menu Items
5. Using On-Screen Menu
Picture
Wall Color Off, Blackboard, Light yellow, Light green, Light blue, Sky blue, Light rose, Pink
Picture Management
Presentation, Video, Movie, Graphic, sRGB
User
Base Setting Presentation, Video, Movie, Graphic, sRGB
Gamma Correction Dynamic, Black Detail, Natural
Brightness R,G,B
Contrast R,G,B
Brightness
Contrast
Sharpness
Color
Hue
Image
Auto Keystone On, Off
Keystone
Keystone Save On, Off
Aspect Ratio Normal, Wide Zoom, Cinema, Native
Cinema Position
Setup
Off Timer Off, 0:30, 1:00, 2:00, 3:00, 4:00, 6:00, 8:00
Lamp Mode Normal, Eco
Language Language-1 English, Deutsch, Français, Italiano, Español, Português, Nederlands
Language-2 Svenska, Norsk, Suomi,
C
esk
y
, Magyar, Polski, Türkçe
Language-3 , , , , , , Dansk
Menu Color Select Color, Monochrome
Menu Display Time Manual, Auto 5 sec, Auto 15sec, Auto 45 sec
Background Blue, Black, Logo
Orientation Desktop Front, Ceiling Rear, Desktop Rear, Ceiling Front
Beep On, Off
Advanced
Security On, Off
Cabinet Button Lock, Unlock
Fan Mode High, Auto
Signal Select COMPUTER1*
RGB/Component, RGB, Component, Scart
COMPUTER2
RGB/Component, RGB, Component
Video Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
S-Video Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Page2 Power Management On, Off
Noise Reduction On, Off
Flicker Reduction On, Off
Auto Adjust Off, Normal, Fine
Horizontal
Ver tical
Clock
Phase
Communication Speed 4800, 9600, 19200
* Only COMPUTER on VT47.
36
5. Using On-Screen Menu
NOTE: Some menu items are not available depending on the input source.
Default
Factory Default Current Signal
All Data
Clear Filter Usage
Clear Lamp Hour Meter
Information
Page1 Remaining Lamp Time, Lamp Hour Meter, Filter Usage, Projector Usage,
BIOS Version, Firmware Version, Data Version
Page2 Source Index, Horizontal Frequency, Vertical Frequency, Sync Polarity
Signal Type, Video Type, Sync Type, Interlace
37
5. Using On-Screen Menu
¿ Menu Descriptions & Functions [Picture]
Using the Wall Color Correction [Wall Color]
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following eight options are available.
• OFF • Blackboard
• Light yellow • Light green
• Light blue • Sky blue
• Light rose • Pink
Using Picture Management [Picture Management]
This option allows you to adjust neutral tint for yellow, cyan or magenta.
There are 5 factory presets optimized for various types of images, or you can set user adjustable settings.
Presentation .......... Recommended for making a presentation using a PowerPoint file
Video ..................... Recommended for regular picture such as TV program
Movie .................... Recommended for movies
Graphic.................. Recommended for graphics
sRGB ..................... Standard color values
User ...................... User adjustable
38
5. Using On-Screen Menu
NOTE: When “sRGB”, “Graphic”, “Video” or “Movie” is selected, the brightness decreases slightly when compared to “Presenta-
tion”. This is not a malfunction.
User Adjust (when using User)
When selecting user adjustable presetting (User), the submenu will be displayed.
You can customize each gamma or color. To do so, first select “User” and press the ENTER button, and then proceed
the following steps.
Selecting Base Setting [Base Setting]
This feature allows you to use white balance or gamma values as reference data to optimize for various types of
images. You can select one of the following five settings.
• Presentation Video
• Movie • Graphic
• sRGB
Selecting Gamma Correction Mode [Gamma Correction]
Each mode is recommended for :
Dynamic ................ Creates a high-contrast picture
Black Detail ........... Emphasizes detail in dark areas of the picture
Natural .................. Natural reproduction of the picture
Adjusting White Balance [Brightness RGB/Contrast RGB]
This allows you to adjust the white balance. Brightness for each color (RGB) is used to adjust the black level of the
screen; Contrast for each color (RGB) to adjust the white level of the screen.
Adjusting Brightness, Contrast, Sharpness, Color and Hue
Brightness ............. Adjusts the brightness level or the back raster intensity.
Contrast ................ Adjusts the intensity of the image according to the incoming signal.
Sharpness ............. Controls the detail of the image for Video.
Color ..................... Increases or decreases the color saturation level (not valid for RGB).
Hue........................ Varies the color level from +/– green to +/– blue. The red level is used as reference. This adjustment is only
valid for Video and Component inputs (not valid for RGB).
39
5. Using On-Screen Menu
´ Menu Descriptions & Functions [Image]
Enabling Auto Keystone [Auto Keystone]
This feature allows the projector to detect its tilt and correct vertical distortion automatically.
To turn on the Auto Keystone feature, select “On”.
Correcting Vertical Keystone Distortion Manually [Keystone]
You can correct vertical distortion manually from the menu when “Auto Keystone” is turned off.
You can save the changes using the Keystone Save feature when you turn off the projector.
Saving Vertical Keystone Correction [Keystone Save]
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are saved when the projector is off.
Selecting Aspect Ratio [ Aspect Ratio]
Aspect Ratio allows you to select the best Aspect mode to display your source image. You can also display the Aspect
Ratio menu by pressing the “ASPECT” button on the remote control.
Normal
Standard
4:3 Aspect
When 16:9 is selected from
the source (i.e. DVD player),
the following selections will
display:
Normal
16:9 image displayed
in 4:3 mode
Wide Zoom Cinema Native
Left and right
stretched
Left and right
stretched
Wide Zoom Cinema Native
Left and right
stretched
Left and right stretched to
display the true aspect
Native (RGB only): Turns off the Advanced AccuBlend feature. The projector displays the current image in its true
resolution.
NOTE:
While you are displaying an image at the projector’s native resolution or higher, “Native” is not available.
•You can adjust the image position for Cinema aspect. See “Cinema Position” for setting the image position.
Copyright
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a
coffee shop or hotel and employing compression or expansion of the screen image with a "Aspect Ratio" setting may raise
concern about the infringement of copyrights which are protected by copyright law.
When 4:3 is selected from
the source (i.e. DVD player),
the following selections will
display:
40
5. Using On-Screen Menu
Adjusting the Vertical Position of Image [Cinema Position] (for Cinema only)
This feature adjusts the vertical position of the image when viewing video with Cinema aspect ratio selected.
When “Cinema” is selected in “Aspect Ratio”, the image is displayed with black borders on the top and bottom.
You can adjust the vertical position between top and bottom.
NOTE: This option is available only when “Cinema” is selected in Aspect Ratio.
² Menu Descriptions & Functions [Setup]
Using Off Timer [Off Timer]
You can set the timer so that the projector turns itself off at the preset time.
1. Use the SELECT
̆
or
̄
button to select your desired time between 30 minutes and 8 hours: Off, 0:30,
1:00, 2:00, 3:00, 4:00, 6:00 and 8:00.
2. Press the ENTER button.
3. The Off Timer starts counting down remaining time.
4. The projector turns off after the countdown is complete.
NOTE:
•To cancel the preset time, select “Off” for the preset time or turn off the power.
When the remaining time reaches 3 minutes before the projector is turned off, the “Projector will turn off in 3 minutes”
message will be displayed on the bottom of the screen.
Selecting Lamp Mode [Lamp Mode]
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended by using the Eco mode.
Normal Mode ........ This is the default setting (100% Brightness).
Eco Mode .............. Select this mode to increase the lamp life (80% Brightness).
NOTE: If the projector is overheated in Normal mode, there may be a case where the Lamp mode automatically changes to Eco
mode to protect the projector. When the projector is in Eco mode, the picture brightness decreases. When the projector comes
back to normal temperature, the Lamp mode returns to Normal mode.
NOTE: Thermometer symbol indicates the lamp mode is automatically set to Eco mode because the internal temperature is too
high.
41
5. Using On-Screen Menu
Selecting Menu Language [Language]
You can choose one of 21 languages for on-screen instructions.
Selecting Menu Color [Menu Color Select]
You can choose between two color modes for menu color: color and monochrome.
Selecting Menu Display Time [Menu Display Time]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu.
The preset choices are “Manual”, “Auto 5 sec”, “Auto 15 sec”, and “Auto 45 sec”. The “Auto 45 sec” is the factory
preset.
Selecting a Color or Logo for Background [Background]
Use this feature to display a black/ blue screen or logo when no signal is available.
Selecting Projector Orientation [Orientation]
This sets your image for your type of projection. The options are:
desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection.
Enabling Key Sound and Error Sound [Beep]
This feature turns on or off the keypad sound or alarm when a button on the cabinet and the remote control is pressed
or an error occurs.
42
5. Using On-Screen Menu
Menu Descriptions & Functions [Advanced]
Security
A keyword can be set for your projector to avoid operation by an unauthorized user using the Menu. When a keyword
is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the
projector cannot project an image.
To enable the Security function:
1. Select [Advanced]
[Security] and press the
̇
button to select “On”.
The [Keyword] screen will be displayed.
The [Confirm Keyword] screen will be displayed.
2. Type in a combination of the four SELECT buttons
̆̄̇̈
and press the ENTER button.
NOTE: A keyword must be four to 10 digits in length.
43
5. Using On-Screen Menu
3. Type in the same combination of SELECT buttons
̆̄̇̈
and press the ENTER button.
The confirmation screen will be displayed.
4. Select “Yes” and press the ENTER button.
The Security function has been enabled.
To disable the Security function:
1. Select [Advanced]
[Security] and press the
̈
button to select “Off”.
2. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the Security function will be disabled.
When the Security function is enabled and the projector is turned on, the projector will display a blue
background.
To display an image at this time, press the MENU button to display the Keyword input screen.
The Keyword confirmation screen will be displayed.
Type in the correct keyword and press the ENTER button. The projector will display an image.
NOTE:
The security disable mode is maintained until the main power is turned off (by setting the main power switch to “O” or
unplugging the power cable).
If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request
code. Your request code is displayed in the Keyword Confirmation screen. In this example “K992-45L8-JNGJ-4XU9-1YAT-
EEA2” is a request code.
44
5. Using On-Screen Menu
Disabling the Cabinet Buttons [Cabinet Button Lock]
This option turns on or off the Cabinet Button Lock function.
NOTE:
This Cabinet Button Lock does not affect the remote control and the PC Control functions.
When the cabinet buttons are unlocked, pressing and holding the EXIT button for about 10 seconds will change the setting to
enable.
Key symbol indicates the Cabinet Button Lock is enabled.
Enabling High Speed Fan Mode [Fan Mode]
This option allows you to select two modes for fan speed: High speed mode and Auto mode.
High ...................... The built-in fans run at a fixed high speed.
Auto ...................... The built-in fans automatically run at a variable speed according to the internal temperature.
When you wish to cool down the temperature inside the projector quickly, select “High”.
NOTE: Select “High” if you continue to use the projector for consecutive days.
Selecting Signal Format [Signal Select]
[Computer]
Allows you to choose “Computer” for an RGB source such as a computer, or “Component” for a component video
source such as a DVD player. Normally select “RGB/Component” and the projector automatically detects a compo-
nent signal. However there may be some component signals that the projector is unable to detect. If this is the
case, select “Component”. Select “Scart” in Computer 1 (Computer on VT47) for the European Scart signal.
[Video & S-Video System Select]
This feature enables you to select composite video standards manually. Normally select “Auto”.
When you select the video standard for Video and S-Video, select the video standard from the pull-down menu.
This must be done for Video and S-Video respectively.
45
5. Using On-Screen Menu
(Advanced Page 2)
Enabling Power Management [Power Management]
When this option is on and there is no input for five minutes or more, the projector will automatically turn itself off.
Turning On Noise Reduction [Noise Reduction] (not available for Video and S-Video signals)
Reduces video noise. Select “On” to enable the Noise Reduction feature.
Turning On Flicker Reduction [Flicker Reduction]
Reduces flicker which can occur in an interlaced signal. This feature is not available for RGB and HDTV signals.
NOTE: When the Flicker Reduction is ON, jagged lines can be visible depending on the signal. In that case, select OFF.
NOTE: This feature may not be available depending on your video equipment connected to the projector.
Setting Auto Adjust [Auto Adjust]
This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise
and stability. You can automatically make adjustment in two ways: Normal and Fine
Off ......................... The RGB image will not be automatically adjusted.
You can manually optimize the RGB image.
Normal .................. Default setting. The RGB image will be automatically adjusted. Normally select this option.
Fine ....................... Select this option if fine adjustment is needed. It takes more time to switch to the source than when “Nor-
mal” is selected.
Adjusting Position/Clock (when Auto Adjust is off)
This allows you to manually adjust the image horizontally and vertically, and adjust Clock and Phase.
[Horizontal/Vertical]
Adjusts the image location horizontally and vertically.
This adjustment is made automatically when the Auto Adjust is turned on.
[Clock] (available for RGB and HDTV signals only)
Use this item with the “Auto Adjust off” to fine tune the computer image or to remove any vertical banding that
might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This
adjustment may be necessary when you connect your computer for the first time. This adjustment is made auto-
matically when the Auto Adjust is turned on.
46
5. Using On-Screen Menu
[Phase] (available for RGB and HDTV signals only)
Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident
when part of your image appears to be shimmering.)
Use “Phase” only after the “Clock” is complete.
This adjustment is made automatically when the Auto Adjust is turned on.
Selecting Communication Speed [Communication Speed]
This feature sets the baud rate of the PC Control port (DIN 8 Pin). It supports data rates from 4800 to 19200 bps.
The default is 19200 bps.
Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate
may be recommended for long cable runs).
º Menu Descriptions & Functions [Information]
Displays the status of the current signal, remaining lamp (%), lamp/filter/projector usage time (hours) and version
information. The Information has two pages. The Information included is as follows:
[Page 1]
Remaining Lamp Time (%)*
Lamp Hour Meter (H)
Filter Usage
Projector Usage
* The progress indicator shows the percentage of remaining bulb life. The value informs you of the amount of
lamp usage. When the remaining lamp time reaches 0, the Remaining Lamp Time bar indicator changes
from 0% to 100 Hours and starts counting down.
If the remaining lamp time reaches 0 hours, the projector will not turn on regardless of whether the lamp
mode is set to Normal or Eco.
BIOS Version
Firmware Version
Data Version
Model
VT676/VT670/
VT470
VT575/VT47
Lamp life(H)
Normal Eco
2000 3000
3000 4000
Replacement lamp
VT75LP
VT70LP
47
5. Using On-Screen Menu
¾ Menu Descriptions & Functions [Default]
Returning to Factory Default [Factory Default]
The Factory Default feature allows you to change adjustments and setting to the factory preset.
[Current Signal]
Resets the adjustments for the current signal to the factory preset levels.
The items that can be reset are: Brightness, Contrast, Color, Hue, Sharpness, Noise Reduction, Aspect Ratio,
Horizontal Position, Vertical Position, Clock, Phase and Picture Management.
[All Data]
Reset all the adjustments and settings for all the signals to the factory preset for source except the following:
Language, Security, Communication Speed, Remaining Lamp Time, Lamp Hour Meter, Filter Usage and Projector
Usage. To reset the lamp usage time, see “Clear Lamp Hour Meter” and “Clear Filter Usage”.
Resetting the Filter Usage Hours [Clear Filter Usage]
Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select “Yes” and press
the ENTER button.
Clearing Lamp Hour Meter [Clear Lamp Hour Meter]
Resets the lamp clock back to zero. Selecting this option displays submenu for a confirmation. Select “Yes” and press
the ENTER button.
NOTE: The projector will turn off and go into standby mode after 2100* hours (up to 3100* hours in Eco mode) of service.
If this happens, press the HELP button on the remote control for ten seconds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
Do this only after replacing the lamp.
* VT575 and VT47: 3100 hours (up to 4100 hours in Eco mode).
[Page 2]
Source Index
Horizontal Frequency
Vertical Frequency
Sync Polarity
Signal Type
Video Type
Sync Type
Interlace
48
6. Maintenance
Z
O
O
M
F
O
CU
S
S
E
L
E
C
T
L
A
M
P
S
T
A
T
U
S
P
O
W
E
R
V
ID
E
O
S
-V
ID
E
O
C
O
M
P
U
T
E
R
-1
C
O
M
P
U
T
E
R
-2
O
N
/S
T
A
N
D
B
Y
A
U
T
O
A
D
J
.
This section describes the simple maintenance procedures you should follow to clean the filter and replace the lamp.
Cleaning or Replacing the Filter
The air-filter sponge keeps dust and dirt from getting inside the projector and should be cleaned after every 100 hours
of operation (more often in dusty conditions). If the filter is dirty or clogged, your projector may overheat.
CAUTION
•Turn off the projector, turn off the main power switch and unplug the projector before replacing the filter.
Only clean the outside of the filter cover with a vacuum cleaner.
Do not attempt to operate the projector without the filter cover.
To clean the air-filter:
Vacuum the filter-through the filter cover.
To reset the filter usage time, from the menu, select [Default] [Clear Filter Usage].
See also page 47 for resetting the filter usage time.
To replace the filter (sponge):
1. Remove the filter cover by pushing down on the catch of the cover until you feel it detach.
Catch
2. Gently peel off the filter (sponge) and replace it with the new one.
49
6. Maintenance
3. Reinstall the new filter cover.
NOTE: Do not wash the filter with soap and water. Soap and water will damage the filter membrane. Before replacing the filter,
remove dust and dirt from the projector cabinet. Keep out dust and dirt during filter replacement.
NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement
lamp.
· Cleaning the Cabinet and the Lens
1. Turn off the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong
detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.
A
C
I
N
Z
O
O
M
F
O
C
U
S
S
E
L
E
C
T
L
A
M
P
S
T
A
T
U
S
P
O
W
E
R
V
ID
E
OS
-
V
ID
E
O
C
O
M
P
U
T
E
R
-1
C
O
M
P
U
T
E
R
-
2
O
N
/S
T
A
N
D
B
Y
A
U
T
O
A
D
J
.
AUDIO OUT
S-VIDEO IN
COMPUTER 1 IN
COMPUTER OUT
PC CONTROL
AUDIO AUDIO
COMPUTER 2 IN
VIDEO IN
AUDIO
L
/M
O
N
O
R
AUDIO
L
/M
O
N
O
R
Z
O
O
M
F
O
CU
S
SELECT
LAMP
STATUS
POWER
VIDEO
S-VIDEO
COMPUTER-1
COMPUTER-2
ON/STAND BY
A
U
T
O
A
D
J
.
50
» Replacing the Lamp
After your lamp has been operating for 2000* hours (up to 3000* hours in Eco mode) or longer, the LAMP indicator in
the cabinet will blink red and the message “The lamp has reached the end of its usable life. Please replace the
lamp. will appear. Even though the lamp may still be working, replace it at 2000* (up to 3000* hours in Eco mode)
hours to maintain optimal projector performance. After replacing the lamp, be sure to clear the lamp hour meter. See
page 47.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,
wait 30 seconds, turn off the main power switch and then disconnect the power cable. Allow at least one hour
for the lamp to cool before handling.
DO NOT REMOVE ANY SCREWS except two lamp case screws. You could receive an electric shock.
Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints in the glass surface might
cause an unwanted shadow and poor picture quality.
The projector will turn off and go into standby mode after 2100* (up to 3100* hours in Eco mode) hours of
service. If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000* hours (up to
3000* hours in Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp
case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for
lamp replacement.
*NOTE: Lamp life for VT575/VT47 is 3000 hours in Normal mode and 4000 hours in Eco mode.
The projector will turn off and go into standby mode after 3100 (up to 4100 hours in Eco mode) hours of service.
To replace the lamp:
Optional lamp and tools needed for replacement:
Replacement lamp VT75LP (VT676/VT670/VT470) or VT70LP (VT575/VT47)
Phillips screwdriver or equivalent
NOTE: The two lamp houses are slightly different in appearance.
The following explanation uses drawings for the lamp VT75LP.
1. Place the projector on a soft cloth and turn it over to access the lamp cover on the bottom.
6. Maintenance
2. Use a Philips screwdriver to push and release the tab.
Push up and remove the lamp cover.
Catch
Philips
screwdriver
51
3. Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling
condition. The two screws are not removable.
Remove the lamp housing by holding it.
6. Maintenance
NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
4. Insert a new lamp housing until the lamp housing is plugged into the socket.
CAUTION
Do not use a lamp other than the NEC replacement lamp VT75LP (VT676/VT670/VT470) or VT70LP (VT575/
VT47).
Order this from your NEC dealer.
Secure it in place with the two screws.
Be sure to tighten the screws.
5. Reattach the lamp cover.
Slip the lamp cover back until it snaps into place.
Interlock
52
6. Maintenance
6. Connect the supplied power cable, turn on the Main Power switch and turn on the projector.
7. Finally, select the menu
[Default]
[Clear Lamp Hour Meter] to reset the lamp usage hours.
NOTE: When the lamp exceeds 2100* hours (up to 3100* hours in Eco mode) of service, the projector cannot turn on and the
menu is not displayed.
If this happens, press the HELP button on the remote control for ten seconds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
* VT575 and VT47: 3100 hours (up to 4100 hours in Eco mode).
53
7. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady light
Green
Orange
Green
Orange
0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
The main power is off
The projector is getting ready to turn on.
Off Timer is enabled.
The projector is cooling down.
The projector is turned on.
The projector is in Standby.
Wait for a moment.
Wait for a moment.
Status Indicator
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady light
Red
Green
Orange
1 cycle (0.5 sec On,
2.5 sec Off)
2 cycle (0.5 sec On,
0.5 sec Off)
4 cycle (0.5 sec On,
0.5 sec Off)
6 cycle (0.5 sec On,
0.5 sec Off)
Normal
Lamp cover error or lamp housing error
Temperature error
Fan error
Lamp error
Re-firing the lamp (The projector is cool-
ing down.)
Cabinet button is locked
Replace the lamp cover or lamp
housing correctly.
The projector is overheated. Move
the projector to a cooler location.
Fans will not work correctly.
Lamp fails to light. Wait a full
minute and then turn on again.
The projector is re-firing.
Wait for a moment.
You have pressed cabinet button
when Cabinet Button is locked.
Lamp Indicator
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady light
Normal
Lamp has reached its end of life. Lamp
replacement message will be displayed.
Lamp has been used beyond its limit. The
projector will not turn on until the lamp is
replaced.
Lamp mode is set to Eco mode
Red
Red
Green
Replace the lamp.
Replace the lamp.
54
7. Appendix
Common Problems & Solutions (See also "Power/Status/Lamp Indicator" on page 53.)
Does not turn on
Will turn off
No picture
Picture suddenly
becomes dark
Color tone or hue is
unusual
Image isn’t square to
the screen
Picture is blurred
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or
blinking
Cross color in RGB
mode
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. See pages 20 and 21.
Ensure that the lamp cover is installed correctly. See page 51.
Check to see if the projector has overheated or the lamp usage exceeds 2100* hours (up to 3100* hours : Eco
mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is par-
ticularly warm, move the projector to a cooler location.
* VT575 and VT47: 3100 hours (up to 4100 hours in Eco mode).
The lamp may fail to light. Wait a full minute and then turn on the power again.
The lamp has reached the end of its usable life. Replace the lamp.
Ensure that the Power Management is off. See page 45.
Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Computer,
Video or S-Video). See page 23. If there is still no picture, press the button again.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. See page 38.
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the “Default” in the Menu. See page 47.
Enter your registered keyword if the Security function is enabled. See page 42.
When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
See also the next page.
When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
* When there are no signals (blue or black screen) To return to the Normal mode, select another available
source.
* When the image is muted using the PIC-MUTE button on the remote control Press the PIC-MUTE button
again to return to the Normal mode.
* When the room where you' re presenting is particularly warm Move the projector to a cooler location.
Check if an appropriate color is selected in "Wall Color". If so, select an appropriate option. See page 37.
Adjust "Hue" in "Picture". See page 38.
Reposition the projector to improve its angle to the screen. See page 24.
Use the Keystone correction function to correct the trapezoid distortion. See page 26.
Adjust the focus. See page 25.
Reposition the projector to improve its angle to the screen. See page 24.
Ensure that the distance between the projector and screen is within the adjustment range of the lens. See
pages 11 for VT676/VT670/VT575/VT470 and 12 for VT47.
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Video, S-
Video or Computer). See page 23.
Adjust the computer image manually with the Horizontal/Vertical in the “Advanced Page 2”. See page 45.
Install new batteries.See page 10.
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. See page 10.
See the POWER/STATUS/LAMP Indicator on page 53.
Press the AUTO ADJ. button on the projector cabinet or the remote control. See page 28.
When “Off” is selected in Auto Adjust, adjust the computer image manually with Clock/Phase in “Advanced
Page 2” in the menu. See pages 45 and 46.
Problem Check These Items
For more information contact your dealer.
55
7. Appendix
If there is no picture, or the picture is not displayed correctly.
Power on process for the projector and the PC.
Be sure to connect the RGB cable between the projector and the computer before turning on the computer.
There are some notebook PCs, which do not output signal unless there is a projector or monitor connected first.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads
“0kHz”, this means there is no signal being output from the computer. See page 46 or go to next step.
Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projec-
tor. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come
on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle
through external display selections.
Non-standard signal output from the computer
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.
Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the
previous step. Refer to your computer’s documentation for detailed information.
Image displayed is incorrect when using a Macintosh
When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projec-
tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP
switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP
switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a
displayable mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.
Mirroring on a PowerBook
* When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirror-
ing” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
Folders or icons are hidden on the Macintosh screen
Folders or icons may not be seen on the screen. Should this happen, select [View] [Arrange] from the Apple
menu and arrange icons.
56
7. Appendix
Specifications
This section provides technical information about the VT676/VT670/VT575/VT470/VT47 Projector's performance.
Model Number VT676/VT670/VT575/VT470/VT47
Optical
LCD Panel 0.7" p-Si TFT active-matrix (with Micro Lens Array on VT676, VT670 and
VT575 only)
Resolution VT676/VT670/VT575: 1024 ן 768 pixels* native, up to UXGA with Ad-
vanced AccuBlend
VT470: 800 ן 600 pixels* native, up to UXGA with Advanced AccuBlend
VT47: 800 ן 600 pixels* native, up to SXGA with Advanced AccuBlend
Lens VT676/VT670/VT575/VT470: Manual zoom and manual focus
F1.7 - 2.0 f=21.6 - 25.9 mm
VT47: Digital zoom and manual focus
F2.0 f=17.5 mm
Lamp VT676 : 190W DC lamp (150W Eco mode)
VT670/VT470: 180W DC lamp (150W Eco mode)
VT575/VT47: 130W DC lamp (110W Eco mode)
Image Size (Diagonal) VT676/VT670/VT575/VT470: 21 - 300 inches / 0.5 - 7.6 m
VT47: 25 - 300 inches / 0.6 - 7.6 m
Projection Distance VT676/VT670/VT575/VT470: 2.4 - 35.89 ft / 0.73 - 10.9 m
VT47: 1.9 - 23.92 ft / 0.58 - 7.3 m
Projection Angle VT676/VT670/VT575/VT470: Tele: 9.5° - 9.9°/ Wide: 11.5° - 12.0°
VT47: 14.0° - 14.6°
Keystone Correction +/- 30° Vertical (auto)
Electrical
Inputs VT676/VT670/VT575/VT470: 2 RGB/Component (D-Sub 15 Pin),
1 S-Video (DIN 4 Pin), 1 Video (RCA), 2 (L/R) RCA Audio,
1 Stereo Mini Audio, 1 PC Control (DIN 8 Pin)
VT47: 1 RGB/Component (D-Sub 15 Pin), 1 S-Video (DIN 4 Pin),
1 Video (RCA), 1 (L/R) RCA Audio, 1 Stereo Mini Audio,
1 PC Control (DIN 8 Pin)
Outputs 1 RGB (D-Sub 15 Pin), 1 Stereo Mini Audio (not available on VT47)
Video Compatibility NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM,
HDTV: 1080i, 1080i/50Hz, 720p, 576p, 480p, 480i/60Hz
Scan Rate Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Ver tical: 50 Hz to 120 Hz
Video Bandwidth RGB: 80 MHz (-3dB)
Color Reproduction 16.7 million colors simultaneously, Full color
Horizontal Resolution NTSC / NTSC4.43/PAL/PAL-M/PAL-N/PAL60: 540 TV lines
SECAM: 300 TV lines
YCbCr: 800 TV lines
RGB: VT676/VT670/VT575: 1024 dots (H)ן768 dots (V),
VT470/VT47: 800 dots (H)ן600 dots (V)
External Control RS232, IR
* Effective pixels are more than 99.99%.
57
7. Appendix
Sync Compatibility Separate Sync / Composite Sync / Sync on G
Built-in Speaker 1W (monaural)
Power Requirement 100 - 240V AC, 50 / 60 Hz
Input Current VT676/VT670/VT470: 2.7 - 1.4A
VT575/VT47: 2.1 - 1.2A
Power Consumption VT676/VT670/VT470: 8W in Standby mode /
250W in Lamp Normal mode / 200W in Lamp Eco mode
VT575/VT47: 8W in Standby mode /
190W in Lamp Normal mode / 155W in Lamp Eco mode
Mechanical
Installation Orientation Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
Dimensions 11.6" (W)ן3.7" (H)ן10.2" (D)
294mm (W)ן93mm (H)ן260mm (D)
(not including protrusions)
Net Weight 6.5 lbs / 2.9 kg
Environmental Considerations Operational Temperatures : 41° to 95°F (5° to 35°C),
20% to 80% humidity (non-condensing)
Storage Temperatures : 14° to 122°F (-10° to 50°C),
20% to 80% humidity (non-condensing)
Regulations
For United States:
UL Approved (UL 60950)
Meets FCC Class B requirements
For Canada:
UL Approved (CSA 60950)
Meets DOC Canada Class B requirements
For Australia/New Zealand:
Meets AS/NZS CISPR.22 Class B
For Europe:
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950, TUV GS Approved)
For additional information visit:
US : http://www.necvisualsystems.com
Europe : http://www.neceurope.com/
Global : http://www.nec-pj.com/
The specifications are subject to change without notice.
58
7. Appendix
Cabinet Dimensions
LAMP
STATUS
POWER VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
ZOOM
FOCUS
SELECT
AC IN
AUDIO OUT
AUDIO
S-VIDEO IN
COMPUTER 2 IN
VIDEO IN
COMPUTER 1 IN
MONITOR OUT
PC CONTROL
L/MONO
R
AUDIO
L/MONO
R
AUDIO
112.5 (4.4)
260 (10.2)
20.3 (0.8)
64.6 (2.5)
294 (11.6)
71.5 (2.8)
Lens center
Lens center
Unit: mm (inch)
VT676/VT670/VT575/VT470
59
LAMP
STATUS
POWER VIDEO S-VIDEO COMPUTER
ON/STAND BY
ZOOM
FOCUS
SELECT
AC IN
112.5 (4.4)
260 (10.2)
20.3 (0.8)
64.6 (2.5)
294 (11.6)
71.5 (2.8)
ZOOM
AUDIO
S-VIDEO IN
VIDEO IN
COMPUTER IN
MONITOR OUT
PC CONTROL
L/MONO
R
AUTO
ADJ.
AUDIO
Lens center
Lens center
Unit: mm (inch)
VT47
7. Appendix
60
Mini D-Sub 15 Pin Connector
Pin Assignments of D-Sub COMPUTER Input Connector
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
51423
10
1112131415
6978
7. Appendix
* Only COMPUTER 1 input connector supported on VT676/VT670/VT575/VT470.
Pin No. RGB Signal (Analog) YCbCr Signal
1 Red Cr
2 Green or Sync on Green Y
3 Blue Cb
4Ground
5Ground
6 Red Ground Cr Ground
7 Green Ground Y Ground
8 Blue Ground Cb Ground
9 No Connection
10 Sync Signal Ground
11 SCART Sync
12 Bi-directional DATA (SDA)*
13
Horizontal Sync or Composite Sync
14 Vertical Sync
15 Data Clock*
61
7. Appendix
Compatible Input Signal List
Signal Resolution Frequency H. Refresh Rate
( Dots ) ( kHz ) ( Hz )
NTSC 15.734 60
PAL–15.625 50
PAL60 15.734 60
SECAM 15.625 50
VESA 640 ן 480 31.47 59.94
IBM 640 ן 480 31.47 60
MAC 640 ן 480 31.47 60
MAC 640 ן 480 34.97 66.67
MAC 640 ן 480 35 66.67
VESA 640 ן 480 37.86 72.81
VESA 640 ן 480 37.5 75
IBM 640 ן 480 39.375 75
VESA 640 ן 480 43.269 85.01
IBM 720 ן 350 31.469 70.09
VESA 720 ן 400 37.927 85.04
IBM 720 ן 350 39.44 87.85
IBM 720 ן 400 39.44 87.85
VESA 800 ן 600 35.16 56.25
VESA 800 ן 600 37.879 60.32
VESA 800 ן 600 48.077 72.19
VESA 800 ן 600 46.88 75
VESA 800 ן 600 53.674 85.06
MAC 832 ן 624 49.725 74.55
@ VESA 1024 ן 768 35.5 43 Interlaced
@ VESA 1024 ן 768 48.363 60
@ VESA 1024 ן 768 56.476 70.07
@MAC 1024 ן 768 60.241 74.93
@ VESA 1024 ן 768 60.023 75.03
@ VESA 1024 ן 768 68.677 85
@#VESA 1152 ן 864 67.5 75
@#MAC1152 ן 870 68.681 75.06
@#SUN 1152 ן 900 61.796 65.95
@#SGI 1152 ן 900 71.736 76.05
@#VESA 1280 ן 960 60 60
@#VESA 1280 ן 1024 63.981 60.02
@#MAC1280 ן 1024 69.89 65.18
@#HP 1280 ן 1024 78.125 72.01
@#SUN 1280 ן 1024 81.13 76.11
@#VESA 1280 ן 1024 79.976 75.03
@#VESA 1280 ן 1024 91.146 85.02
@#SXGA+ 1400 ן 1050
@#
HDTV
(1080p)
1920 ן 1080 67.5 60 Progressive
@#
SDTV(576i)(625i)
15.6 50
@#
SDTV(576p)(625p)
31.5 50
@#
HDTV
(1080i)(1125i)
1920 ן 1080 33.75 60 Interlace
@#
HDTV
(1080i)(1125i)
1920 ן 1080 28.125 50 Interlace
@#
HDTV (720p)(750p)
1280 ן 720 45 60 Progressive
@#
SDTV (480p)(525p)
31.47 59.94 Progressive
@# * VESA 1600 ן 1200 75.0 60
@# * VESA 1600 ן 1200 81.25 65
@# * VESA 1600 ן 1200 87.5 70
@# * VESA 1600 ן 1200 93.75 75
DVD YCbCr 15.734 59.94 Interlaced
DVD YCbCr 15.625 50 Interlaced
#:Images in above flagged with # are compressed with Advanced AccuBlend on VT676/VT670/
VT575.
@: Images in above flagged with @ are compressed with Advanced AccuBlend on VT470/VT47.
*:Images in above flagged with * are not supported on VT47.
NOTE: Some composite sync signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change
the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
UXGA (1600
ן
1200) is supported for separate sync signal only.
62
7. Appendix
PC Control Codes and Cable Connection
PC Control Codes (VT676/VT670/VT575/VT470)
Function Code Data
POWER ON 02H 00H 00H 00H 00H 02H
POWER OFF 02H 01H 00H 00H 00H 03H
INPUT SELECT COMPUTER 1 02H 03H 00H 00H 02H 01H 01H 09H
INPUT SELECT COMPUTER 2 02H 03H 00H 00H 02H 01H 02H 0AH
INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH
INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H
PICTURE MUTE ON 02H 10H 00H 00H 00H 12H
PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H
SOUND MUTE ON 02H 12H 00H 00H 00H 14H
SOUND MUTE OFF 02H 13H 00H 00H 00H 15H
PC Control Codes (VT47)
Function Code Data
POWER ON 02H 00H 00H 00H 00H 02H
POWER OFF 02H 01H 00H 00H 00H 03H
INPUT SELECT COMPUTER 02H 03H 00H 00H 02H 01H 01H 09H
INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH
INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H
PICTURE MUTE ON 02H 10H 00H 00H 00H 12H
PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H
SOUND MUTE ON 02H 12H 00H 00H 00H 14H
SOUND MUTE OFF 02H 13H 00H 00H 00H 15H
Cable Connection
Communication Protocol
Baud rate ........................................ 19200 bps
Data length ..................................... 8 bits
Parity .............................................. No parity
Stop bit .......................................... One bit
X on/off .......................................... None
Communications procedure ........... Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
NOTE: Contact your local dealer for a full list of the PC Contorol Codes if needed.
63
7. Appendix
12
54 3
6
7
8
To RxD of PC
PC Control Connector (DIN-8P)
To TxD of PCTo GND of PC
NOTE: Pins 2, 3, 5, 6 and 8 are used inside the projector.
70

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nec VT 676 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nec VT 676 in de taal/talen: Engels als bijlage per email.

De handleiding is 3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info