493609
94
Verklein
Vergroot
Pagina terug
1/107
Pagina verder
85
7. Appendix
Common Problems & Solutions ( “Power/Status/Lamp Indicator” on page 84.)
Problem Check These Items
Does not turn on
or shut down
Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control
is on. ( pages 19 and 20)
Ensure that the lamp cover is installed correctly. ( page 83)
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the
room where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its life.
If so, replace the lamp. After replacing the lamp, reset the lamp hours used. ( page 79)
The lamp may fail to light. Wait a full minute and then turn on the power again.
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1700
meters (3000 feet/900 meters on V300X/V300W) or higher. Using the projector at altitudes approximately 5500
feet/1700 meters or higher without setting to [HIGH ALTITUDE] can cause the projector to overheat and the
projector could shut down. If this happens, wait a couple minutes and turn on the projector. ( page 70)
If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image
for some time and then the projector will display the image. Wait for a moment.
Will turn off
Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. ( page 65, 73)
No picture
Use the COMPUTER1, the VIDEO or the S-VIDEO button on the remote control to select your source (Com-
puter, Video or S-Video). ( page 22) If there is still no picture, press the button again.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. ( page 58)
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. ( page 79)
Enter your registered keyword if the Security function is enabled. ( page 34)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning
on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software.
See also the next page.
Picture suddenly be-
comes dark
Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case, lower
the internal temperature of the projector by selecting [HIGH] for [FAN MODE]. ( page 70)
Color tone or hue is
unusual
Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. ( page 64)
Adjust [HUE] in [PICTURE]. ( page 58)
Image isn’t square to the
screen
Reposition the projector to improve its angle to the screen. ( page 23)
Use the Keystone correction function to correct the trapezoid distortion. ( page 26)
Picture is blurred
Adjust the focus. ( page 25)
Reposition the projector to improve its angle to the screen. ( page 23)
Ensure that the distance between the projector and screen is within the adjustment range of the lens.
( page 11)
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Flicker appears on
screen
Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately
5500 feet/1700 meters (3000 feet/900 meters on V300X/V300W) or lower. Using the projector at altitudes less
than approximately 5500 feet/1700 meters (3000 feet/900 meters on V300X/V300W) and setting to [HIGH
ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO]. (
page
70
)
Image is scrolling ver-
tically, horizontally or
both
Check the computer's resolution and frequency. Make sure that the resolution you are trying to display is sup-
ported by the projector. ( page 93)
Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. ( page 61)
Remote control does
not work
Install new batteries.( page 8)
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. ( page 8)
Make sure that the remote control's ID corresponds with the projector's ID. ( page 69)
Indicator is lit or blink-
ing
See the POWER/STATUS/LAMP Indicator. ( page 84)
Cross color in RGB
mode
Press the AUTO ADJ. button on the projector cabinet or the remote control. ( page 28)
Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. ( page
60)
Cannot control the pro-
jector from external
equipment
Check to see if [STANDBY MODE] is set to [POWER-SAVING] and if it is, try to set it to [NORMAL]. ( page
72)
3D picture is not display
See "Troubleshooting on viewing 3D images" on page 51.
For more information contact your dealer.
94

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nec NP-V300X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nec NP-V300X in de taal/talen: Engels als bijlage per email.

De handleiding is 3,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Nec NP-V300X

Nec NP-V300X Snelstart handleiding - Nederlands - 6 pagina's

Nec NP-V300X Gebruiksaanwijzing - Deutsch - 108 pagina's

Nec NP-V300X Snelstart handleiding - English - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info