493586
6
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
E – 1
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
L
E
C
T
P
O
W
E
R
S
T
A
T
U
S
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
A
C
IN
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
U
S
B
P
C
-C
A
R
D
C CONTROL
MOUSE
OUT
REMO
CONTR
INPU
MultiSync MT1055/MT1050/MT850
LCD Projector
Users Manual
English
E 2
IMPORTANT INFORMATION
Precautions
Please read this manual carefully before using your NEC MultiSync
MT1055/MT1050/MT850 Projector and keep the manual handy for fu-
ture reference.
Your serial number is located under the name plate label on the left
side of your MultiSync MT1055/MT1050/MT850. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from
power outlet.
The power outlet socket should be installed as near to
the equipment as possible, and should be easily acces-
sible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE
PERSONNEL.
This symbol warns the user that uninsulated voltage
within the unit may be sufficient to cause electrical shock.
Therefore, it is dangerous to make any kind of contact
with any part inside of the unit.
This symbol alerts the user that important information
concerning the operation and maintenance of this unit
has been provided. The information should be read care-
fully to avoid problems.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTEN-
SION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN
BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM-
PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI-
FIED NEC SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
3. GSGV Acoustic Noise Information Ordinance:
The sound pressure level is less than 70 dB (A) according to ISO 3744
or ISO 7779.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified by
NEC Technologies in this manual. Failure to comply with this gov-
ernment regulation could void your right to operate this equip-
ment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following mea-
sures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
In UK, a BS approved power cable with moulded plug has a Black (five
Amps) fuse installed for use with this equipment. If a power cable is not
supplied with this equipment please contact your supplier.
CAUTION
LASER RADIATION-
DO NOT STATE INTO BEAM
RADIACION LASER
NO MIRE AL RAYO
PRODUCTO LASER CLASSE2
LASER-STRAHLUNG
NICHT IN DEN STRAHL
BLICKEN ! LASER KLASSE2
RAYONNEMENT LASER NE PAS
REGARDER DANS LE FAISCEAU
APPAREIL A LASER DE CLASSE2
EN60825-1 : 1994 + A11 : 1996 MADE IN CHINA
WAVE LENGTH: 650nm
MAX. OUTPUT: 1mW
CLASS 2 LASER PRODUCT
REMOTE
CONTROL
MODEL:
RD-367E
7N900011
IBM is a registered trademark of International Business Machines
Corporation.
Macintosh and PowerBook are registered trademarks of Apple Com-
puter, Inc.
Other product and company names mentioned in this user's manual
may be the trademarks of their respective holders.
This label is located on the back of the remote control.
E 3
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed all
warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from
dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat
radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal com-
ponents.
5. Handle your projector carefully. Dropping or jarring can damage in-
ternal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order to ensure
proper operation and reduce the risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the projector
and the installation must be in accordance with any local building codes.
d. Please consult your dealer for more information.
Power Supply
1. The projector is designed to operate on a power supply of 100-120
or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this
requirement before attempting to use your projector.
2. Handle the power cable carefully and avoid excessive bending. A
damaged cord can cause electric shock or fire.
3. If the projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,
use a mild detergent. Never use strong detergents or solvents such
as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to
scratch or mar the lens.
CAUTION
Do not unplug the power cable from the wall outlet under any one
of the following circumstances. Doing so can cause damage to
the projector:
While the Hour Glass icon appears.
While the message "Please wait a moment." appears. This message
will be displayed after the projector is turned off.
Immediately after the power cable is plugged into the wall outlet (the
POWER indicator has not changed to a steady orange glow).
Immediately after the cooling fan stops working (The cooling fan con-
tinues to work for ONE minute after the projector is turned off with the
POWER button).
While the POWER and the STATUS indicators are alternately flashing.
CAUTION
Do not put the projector on its side when the lamp is turned on.
Doing so may cause damage to the projector.
Lamp Replacement
To replace the lamp, follow all instructions provided on page E-47.
Be sure to replace the lamp when the message "The Lamp has
reached the end of its usable life. Please replace the lamp."
appears. If you continue to use the lamp after the lamp has reached
the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury. If this happens, contact your NEC
dealer for lamp replacement.
Allow a minimum of ONE minute to elapse after turning off the pro-
jector. Then disconnect the power cable and allow 60 minutes to
cool the projector before replacing the lamp.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unob-
structed to prevent the build-up of heat inside your projector. Allow
at least 3 inches (10 cm) of space between your projector and a
wall.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector. Do not attempt to retrieve any objects that
might fall into your projector. Do not insert any metal objects such as
a wire or screwdriver into your projector. If something should fall into
your projector, disconnect it immediately and have the object re-
moved by a qualified NEC service personnel.
3. Do not place any liquids on top of your projector.
Do not look into the lens while the projector is on. Serious damage
to your eyes could result.
Keep any items such as magnifying glass out of the light path of the
projector. The light being projected from the lens is extensive, there-
fore any kind of abnormal objects that can redirect light coming out
of the lens, can cause unpredictable outcome such as fire or injury
to the eyes.
Do not cover the lens with the supplied lens cap or equivalent while
the projector is on. Doing so can lead to melting of the cap and
possibly burning your hands due to the heat emitted from the light
output.
Do not look into the laser pointer while it is on and do not point the
laser beam at another person. Serious injury could result.
E 4
TABLE OF CONTENTS
1. INTRODUCTION
Introduction to the MultiSync MT1055/MT1050/MT850 Projector
.......... E-5
Getting Started............................................................................. E-5
What's in the Box ......................................................................... E-6
Getting to Know Your MultiSync MT1055/MT1050/MT850 Projector
...... E-7
Front / Side Features ............................................................. E-7
Rear / Side Features.............................................................. E-7
Top Features .......................................................................... E-8
Terminal Panel Features ........................................................ E-9
Remote Control Features .................................................... E-10
Remote Control Battery Installation .............................. E-12
Operating Range ........................................................... E-12
Remote Control Precautions ......................................... E-12
Switching Operation mode between mouse and projector
..... E-13
2. INSTALLATION
Setting Up Your Projector ........................................................... E-14
Selecting a Location ................................................................... E-14
Using a Tabletop or Cart ............................................................ E-14
Adjusting the Tilt Foot................................................................. E-15
Distance Chart ........................................................................... E-16
Ceiling Installation ...................................................................... E-16
Reflecting the Image .................................................................. E-16
Wiring Diagram .......................................................................... E-18
Connecting Your PC ............................................................. E-19
Connecting Your Macintosh Computer................................. E-20
Connecting Your Computer to the Mouse Output Port ......... E-21
Connecting an External Monitor .......................................... E-21
Connecting Your DVD Player ............................................... E-22
Connecting Your VCR or Laser Disc Player ......................... E-23
About Startup screen (Menu Language Select screen) ............. E-24
3. OPERATION
General Controls ........................................................................ E-25
Using the Menus .................................................................. E-25
Using a USB Mouse ............................................................ E-25
Basic Operation ................................................................... E-26
Adjust the Image Using Auto Adjust .................................... E-26
Using Pointer ....................................................................... E-27
Enlarging and Moving a Picture ........................................... E-27
Correcting Keystone Distortion ............................................ E-28
Freezing a Picture ................................................................ E-28
Customizing Basic/Custom Menu ........................................ E-28
Menu Tree .................................................................................. E-30
Menu Elements .......................................................................... E-31
Menu Descriptions & Functions ................................................. E-32
Source Select............................................................................. E-32
RGB1&2/Video/S-Video/PC Card Viewer
Picture ........................................................................................ E-32
Brightness/Contrast/Color/Hue/Sharpness
Volume ....................................................................................... E-32
Image Options ............................................................................ E-33
Keystone .............................................................................. E-33
Color Temperature ............................................................... E-33
Lamp Mode .......................................................................... E-33
Gamma Correction .............................................................. E-33
Aspect Ratio ........................................................................ E-33
Noise Reduction .................................................................. E-34
Color Matrix ......................................................................... E-34
White Balance ..................................................................... E-34
Position/Clock ...................................................................... E-34
Resolution ............................................................................ E-34
Video Filter .......................................................................... E-34
Factory Default .................................................................... E-35
Projector Options ....................................................................... E-35
Menu .................................................................................... E-35
Menu Mode ................................................................... E-35
Advanced Menu, Basic/Custom Menu ...................... E-35
Language ...................................................................... E-35
Projector Pointer............................................................ E-35
Source Display .............................................................. E-35
Direct Button (Volume Bar and Keystone Bar) .............. E-35
Menu Display Time ........................................................ E-35
Setup ................................................................................... E-36
Orientation ..................................................................... E-36
Background ................................................................... E-36
Mouse Settings ............................................................. E-36
Button/Sensitivity ....................................................... E-36
PC Card Viewer Options ............................................... E-36
Capture Options ............................................................ E-36
Signal Select ................................................................. E-36
Auto Adjust (RGB only) ................................................. E-37
Auto Start ...................................................................... E-37
Power Management ...................................................... E-37
Power Off Confirmation ................................................. E-37
Keystone Save .............................................................. E-37
Fan High Speed Mode .................................................. E-37
Auto Mute for Built-in Speaker....................................... E-37
Clear Lamp Hour Meter ................................................. E-37
Remote Sensor ............................................................. E-37
S-Video Mode Select .................................................... E-37
RGBOUT Terminal ........................................................ E-37
Communication Speed .................................................. E-38
Default Source Select.................................................... E-38
Tools ........................................................................................... E-38
Capture ................................................................................ E-38
PC Card Files ...................................................................... E-38
Changing Background Logo .......................................... E-39
Chalk Board ......................................................................... E-39
Help ............................................................................................ E-39
Contents .............................................................................. E-39
Information ........................................................................... E-39
Using the PC Card Viewer Function........................................... E-40
Features............................................................................... E-40
Inserting and Ejecting a PC Card ........................................ E-40
Installing the PC Card Viewer Software ............................... E-41
Starting Up the PC Card Viewer Software on your PC
(PC Card Viewer Utility 10) ........ E-41
Operating the PC Card Viewer Function from the Projector
(playback) .................................. E-42
Capturing Images Displayed on the Projector ..................... E-44
Viewing Digital Images ........................................................ E-44
Uninstalling the PC Card Viewer Software .......................... E-45
Terminology ......................................................................... E-46
4. MAINTENANCE
Replacing the Lamp ................................................................... E-47
Cleaning or Replacing the Filters ............................................... E-48
5. TROUBLESHOOTING
Power / Status Light Messages.................................................. E-49
Common Problems & Solutions ................................................. E-49
6. SPECIFICATIONS
Optical/Electrical/Mechanical ..................................................... E-51
Cabinet Dimensions ................................................................... E-52
D-Sub Pin Assignments ............................................................. E-54
Timing Chart .............................................................................. E-55
PC Control Codes ...................................................................... E-56
Cable Connection....................................................................... E-56
E 5
1. INTRODUCTION
Introduction to the MultiSync MT1055/MT1050/
MT850 Projector
This section introduces you to your new MultiSync MT1055 and MT1050
(XGA)/ MT850 (SVGA) Projector and describes the features and con-
trols.
Congratulations on Your Purchase of The
MultiSync MT1055/MT1050/MT850 Projector
The MultiSync MT1055/MT1050/MT850 is one of the very best projec-
tors available today. The MultiSync MT1055/MT1050/MT850 enables
you to project precise images up to 300 inches across (measured di-
agonally) from your PC or Macintosh computer (desktop or notebook),
VCR, DVD player, document camera, a laser disc player or PC Card
Viewer.
You can use the projector on a tabletop or cart, you can use the projec-
tor to project images from behind the screen, and the projector can be
permanently mounted on a ceiling*
1
. The remote control can be used
wirelessly.
Features you’ll enjoy:
Simple set up and operation.
Hot air blown from the vents does not bother the audience during
your presentation since the vents are located at the front of the pro-
jector.
A high-performance 200 watt NSH lamp.
The supplied wireless remote control that operates the projector from
any angle.
The image can be projected between 30 and 300 inches (measured
diagonally).
Keystone correction allows you to correct trapezoidal distortion so
that the image is square.
You can choose between video modes depending on your source:
"normal" for a typical picture, "natural" for true color reproduction.
The built-in PC Card Viewer allows you to start your presentation
even when a PC is not available at the site.
The "Capture" enables you to capture the current projected image.
An image can be projected from in front or behind a screen, and the
projector can even be installed on the ceiling.
NEC Technologies exclusive Advanced AccuBlend intelligent pixel
blending technology - an extremely accurate image compression
technology - offers a crisp image with UXGA (1600ן1200) resolu-
tion*
3
.
Supports most IBM VGA, SVGA, XGA*
2
, SXGA/UXGA(with Ad-
vanced AccuBlend)*
3
, Macintosh, component signal (YCbCr / YPbPr)
or any other RGB signals within a horizontal frequency range of 15
to 100 kHz and a vertical frequency range of 50 to 120 Hz. This
includes NTSC, PAL, PAL60, SECAM and NTSC4.43 standard video
signals.
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
The supplied remote control can be used without a cable, and you
can even use the remote control and mouse adapter to operate your
PC or Macintosh mouse wirelessly from across the room with the
built-in remote mouse receiver.
You can control the projector with a PC using the PC Control port*
4
.
USB terminal allows USB mouse operation *
5
.
The contemporary cabinet design is light, compact, easy to carry,
and complements any office, boardroom or auditorium.
Eight pointers are available for your presentation.
*
1
Do not attempt to mount the projector on a ceiling yourself. The pro-
jector must be installed by qualified technicians in order to ensure
proper operation and reduce the risk of bodily injury. In addition, the
ceiling must be strong enough to support the projector and the in-
stallation must be in accordance with any local building codes. Please
consult your dealer for more information.
*
2
An XGA image (1024ן768) is converted into an 800ן600 crisp
image with NEC technologys Advanced AccuBlend on MT850.
*
3
A UXGA (1600ן1200) and SXGA image (1280ן1024) are displayed
with NEC technologys Advanced AccuBlend on MT1055/MT1050.
*
4
The PC Control Utility 1.0 is required. This program is included on
the supplied CD-ROM.
*
5
The USB terminal meets the USB1.1 specification and accepts a
USB mouse only.
Getting Started
The fastest way to get started is to take your time and do everything
right the first time. Take a few minutes now to review the users manual.
This may save you time later on. At the beginning of each section of
the manual youll find an overview. If the section doesnt apply, you can
skip it.
E 6
What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your MultiSync MT1055/MT1050/MT850 Projector.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
O
N
/
STAND BY
SOURCE
AUTO ADJUST
A
C
IN
S
-V
ID
E
O
V
ID
E
O
A
U
D
IO
R
G
B
IN
P
U
T
2
A
U
D
I
O
R
G
B
IN
P
U
T
1
L
/
M
O
N
O
R
A
U
D
IO
R
G
B
M
O
N
IT
O
R
O
U
T
P
U
T
USB
PC-CARD
C
C
O
N
T
R
O
L
M
O
U
S
E
O
U
T
R
E
M
O
C
O
N
T
R
IN
P
U
+
-
KEYSTONE
F
R
E
E
Z
E
PIC
-
MUTE
H
E
L
P
POINTER
P
C
C
A
R
D
V
ID
E
O
S
-
V
ID
E
O
A
U
T
O
A
D
J
.
R
G
B
1
M
E
N
U
LA
S
E
R
R
-
C
L
I
C
K
/
C
A
N
C
E
L
R
G
B
2
P
J
O
NO
F
F
M
A
G
N
I
F
Y
V
O
L
.
S
L
ID
E
F
O
L
D
E
R
S
LID
E
L
IS
T
Quick
Connect
Guide
User's
Manual
NEC MultiSync MT1055, MT1050 or MT850 projector
Lens cap
String and rivet
Batteries (AAן2)
Power cable
Serial cable RGB signal cable
(15-Pin Mini D-Sub To 15-Pin Mini D-Sub connector)
Mouse adapter
(For IBM PS/2)
Mouse adapter
(For Macintosh)
Remote cable
CD-ROM
Remote control
Mouse adapter
(USB)
E 7
Getting to Know Your MultiSync MT1055/MT1050/MT850 Projector
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
L
E
C
T
P
O
W
E
R
S
T
A
T
U
S
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
A
C
I
N
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
U
S
B
P
C
-
C
A
R
D
C CONTROL
MOUSE
OUT
REMO
CONTR
INPU
Zoom
Remote Sensor
Air-Filter
Lenscap
AC Input
Connect the supplied power cable’s three-
pin plug here.
Adjustable Tilt Foot
Lens
Ventilation (outlet)
Carrying Handle
Terminal Panel
Air Filter
Slot for Kensington
Micro saver Security
System
PC Card Slot
USB (Mouse)
Terminal
Controls
Remote Sensor
Front/Side Features
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
L
E
C
T
P
O
W
E
R
S
T
A
T
U
S
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
Rear/Side Features
Remote Sensor
One-touch Tilt Button
Lamp Cover
Lamp Cover Screw
Rear Foot
Built-In Stereo Speaker (1W)
Remote Sensor
Rear Foot
Built-In Stereo Speaker (1W)
Focus
E 8
1. Source Button
Use this button to select a video source such as a PC, VCR, DVD
player or PC Card Viewer (PC card).
Each time this button is pressed, the input source will change as fol-
lows:
RGB1 RGB2 Video S-Video PC Card Viewer
If no input signal is present, the input will be skipped.
2. Auto Adjust Button (RGB only)
Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture. Some signals may not be displayed correctly or take
time to switch between sources.
3. Menu Button
Displays the menu.
4. Select ▲▼ / Volume (+) (-) Buttons
▲▼: Use these buttons to select the menu of the item you wish to
adjust.
When no menus appear, these buttons work as a volume con-
trol.
: Use these buttons to change the level of a selected menu item.
A press of the button executes the selection.
When the menus or the Viewer tool bar is not displayed, these
buttons can be used to select a slide, or to move the cursor in
Folder List or Slide List.
When the pointer is displayed, these ▲▼ buttons move
the pointer.
5. Enter Button
Executes your menu selection and activates items selected from the
menu.
Top Features
6. Cancel Button
Press this button to exit "Menus". Press this button to return the adjust-
ments to the last condition while you are in the adjustment or setting
menu.
7. Status Indicator
When this is lit red (orange in Eco mode) continually, it's warning you
that the projection lamp has exceeded 1500 hours (2500 hours in Eco
mode) of service. After this light appears, it is advisable to replace the
projection lamp as soon as possible. (See page E-47). In addition the
message "The lamp has reached the end of its usable life. Please re-
place the lamp." appears continually until the lamp is replaced.
If this light blinks red rapidly, it indicates that the lamp cover is not
attached properly or the projector is overheated.
See the Power / Status Light Messages on page E-49 for more details.
8. Power Indicator ( )
When this indicator is green, the projector is on; when the indicator is
orange, it is in standby mode.
9. Power Button (ON / STAND BY)
Use this button to turn the power on and off when the power is sup-
plied and the projector is in standby mode.
NOTE: To turn off the projector, press and hold this button for a minimum of
two seconds.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
STAND BY
SOURCE AUTO ADJUST
1
5
7
8
2
3
4
6
9
E 9
M
E
N
U
R
C
E
A
U
T
O
A
D
J
U
S
T
U
S
B
P
C
-
C
A
R
D
Terminal Panel Features
Slot for Kensington
MicroSaver Security System
14
USB
12 3
4
1. USB Terminal
Connect a commercially available mouse that supports USB. You can
operate the menu or PC Card Viewer with the USB mouse via this
terminal.
Note that this terminal is not used with a computer and that there may
be some brands of USB mouse that the projector does not support.
2 PC Card Slot
Insert a PC card here.
3. PC Card Access Indicator
Lights while accessing a PC card.
4. PC Card Eject Button
Press to eject a PC card.
5. PC Control Port (Mini DIN 8 Pin)
Use this port to connect your PC to control your projector via a serial
cable. This enables you to use your PC and serial communication pro-
tocol to control the projector. The NEC optional serial cable is required
to use this port. Also PC Control Utility 1.0 included in the supplied CD-
ROM must be installed on your PC.
If you are writing your own program, typical PC control codes are on
page E-56.
A cap is put on the port at the factory. Remove the cap when using the
port.
6. Mouse Output Port (Mini DIN 8 Pin)
Use this port to operate your computer's mouse functions from the
remote control.
7. Remote Control Input Jack
Connect your remote control cable here for wired operation.
8. Audio Monitor Output Mini Jack
Connect additional external speakers here to listen to audio coming
from your computer, Video or S- Video input.
RGB Monitor Output Connector (Mini D-Sub 15 pin)
You can use this connector to loop your computer image to an external
monitor from the RGB input source.
9. RGB Audio Input 1 Connector
This is where you connect RGB audio output from a computer or an-
other RGB source.
RGB Input 1 Connector (Mini D-Sub 15 pin)
Connect your PC or other RGB equipment. Use the signal cable that's
supplied to connect to a PC.
10. RGB Audio Input 2 Connector
This is where you connect RGB audio output from a computer or an-
other RGB source.
RGB Input 2 Connector (Mini D-Sub 15 pin)
Connect your PC or other RGB equipment. Use the signal cable that's
supplied to connect to a PC.
11. S-Video Input Port
Here is where you connect the S-Video input from an external source
like a VCR.
12. Left Channel/Mono Audio Input Jack (RCA)
This is the left channel audio input for stereo sound coming from video
equipment or audio system. This also serves as your monaural audio
input. (Video and S-video only)
Right Channel Audio Input Jack (RCA)
This is the right channel audio input for stereo sound. (Video and S-
video only)
NOTE: When using two Video sources simultaneously, the Left Channel Audio
Input jack is available for the S-Video source only and the Right Channel Audio
Input jack is available for the composite video source only.
13. Video Input
Connect a VCR, DVD player, laser disc player, or document camera
here to project video.
14. Built-in Security Slot ( )
This security slot supports the MicroSaver
®
Security System.
MicroSaver
®
is a registered trademark of Kensington Microware
Inc. The logo is trademarked and owned by Kensington Microware Inc.
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
8
9
10
11 12 13
PC CONTROL
REMOTE
CONTROL
INPUT
MOUSE
OUTPUT
5
6
7
E 10
Remote Control Features
NOTE: If you are using a Macintosh computer, you can click either the right-
click or left-click button to activate the mouse.
NOTE: If any one of the buttons is pressed and held for 60 seconds or more,
the button operations will cease to operate. This is not a malfunction, rather it
is a feature used to prolong battery power. To cancel this feature, press any one
of the buttons other than the Mouse button.
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projector
cabinet.
2. Laser Pointer
Beams a laser light when "Laser" button is pressed.
3. LED
Flashes when any button is pressed.
4. Power On Button
If the main power is applied, you can use this button to turn your pro-
jector on.
5. Power Off Button
If the main power is applied, you can use this button to turn your pro-
jector off.
NOTE: To turn off the projector, press and hold the POWER OFF button for a
minimum of two seconds.
6. Video Button
Press this button to select an NTSC, PAL, SECAM or NTSC4.43 com-
patible video source from a VCR, DVD player, laser disc player or docu-
ment camera.
7. S-Video Button
Press this button to select an S-Video source from a VCR.
8. RGB 1 Button
Press this button to select a video source from computer or compo-
nent equipment connected to your RGB 1 port.
9. RGB 2 Button
Press this button to select a video source from computer or compo-
nent equipment connected to your RGB 2 port.
10. Auto Adjust Button (RGB only)
Press this button to automatically adjust the vertical/horizontal posi-
tion, clock frequency/phase and resolution if the projected picture is
not centered, if there are vertical stripes on the picture or if the picture
is flickering.
11. PJ Button
Press this button to switch the Mouse, Cancel/Right Click, and Enter/
Left Click buttons between the Projector mode (lit red) and the Com-
puter mode. Press this button or any one of the Menu, Help, Pointer,
PC Card, Folder List or Slide List buttons to switch to the Projector
mode and the PJ button lights red. To switch back to the Computer
mode, press the PJ button again.
12. Laser Button
Press and hold this button to activate the laser pointer. When lit, you
can use the laser to draw your audience's attention to a red dot that
you can place on any object.
13. Menu Button
Displays the menu for various settings and adjustments.
14. Mouse (▲▼
) / (+) (–) Button
When you are in the Computer mode, these buttons work as a com-
puter mouse.
When you are in the Projector mode, which is indicated by lighting the
PJ button:
▲▼: Use these buttons to select the menu of the item you wish to
adjust.
: Use these buttons to change the level of a selected menu item.
A press of the
button executes the selection.
When the pointer is displayed, these ▲▼
buttons move the
pointer.
1
2
KEYSTONE
FREEZE
PIC
-
MUTE
HELP
POINTER
PC CARD
VIDEO S
-
VIDEO
AUTO ADJ.
RGB 1
MENU LASER
R-CLICK /CANCEL
RGB 2 P
J
ONOFF
MAGNIFY
VOL.
SLIDE
FOLDER
SLIDE
LIST
3
54
10
11
*
12
9
6
8
7
13
*
14
E 11
16. Cancel/ Right Click Button
When you are in the Computer mode, this button works as the mouse
right button.
When you are in the Projector mode, which is indicated by lighting the
PJ button:
Press this button to exit "Menus". It works the same way as the Can-
cel button on the cabinet.
17. Pointer Button
Press this button to display one of the eight pointers; press again to
hide the pointer. You can move your pointer icon to the area you want
on the screen using the Mouse button.
18. Help Button
Provides information about operation and adjustment procedures or
the set information for the current menu or adjustment during menu
operation.
19. Keystone (+) () Button
Press the (+) or () button to correct the keystone (trapezoidal) distor-
tion, and make the image square.
20. Magnify (+) () Button
Use this button to adjust the image size up to 400%.
When the pointer is displayed, the image is magnified about the center
of the pointer. When the pointer is not displayed, the image is magni-
fied about the center of the screen.
When the image is magnified, the pointer is changed to the magnifying
icon.
21. Freeze Button
This button will freeze a picture. Press again to resume motion.
22. Picture Mute Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
NOTE: When the menu is displayed, a press of this button mutes an
image and sound without turning off the menu.
23. Volume (+) () Button
Press (+) to increase the volume and () to decrease it.
24. PC Card Button
Press this button to select the PC Card Viewer source.
25. Slide (+) () Button
Press (+) to select the next folder or slide and () to select the previous
folder or slide.
26. Folder List Button
Press this button to select PC Card Viewer source to display a list of
folders included in a PC card.
27. Slide List Button
Press this button to select PC Card Viewer source to display a list of
slides included in a PC card.
28. Remote Jack
Connect your remote control cable here for wired operation.
*NOTE: The default is the Computer mode, which allows you to use the Mouse,
R-Click/Cancel, and L-Click/Enter buttons as your computer mouse. When the
MENU, HELP, POINTER, PC CARD, FOLDER LIST, or SLIDE LIST button is
pressed, the PJ button lights red to indicate that you are in the Projector mode.
If no buttons are pressed within 10 seconds, the light goes out and the Projec-
tor mode is canceled.
15
KEYSTONE
FREEZE
PIC
-
MUTE
HELP
POINTER
PC CARD
VIDEO S
-
VIDEO
AUTO ADJ.
RGB 1
MENU LASER
R-CLICK /CANCEL
RGB 2 P
J
ONOFF
MAGNIFY
VOL.
SLIDE
FOLDER
SLIDE
LIST
17
*
18
*
19
20
21
22
23
16
24
*
25
26
*
27
*
15. Enter / Left Click Button
When you are in the Computer mode, this button works as the mouse
left button.
When you are in the Projector mode, which is indicated by lighting the
PJ button:
Use this button to enter your menu selection. It works the same way as
the "Enter" button on the cabinet.
E
L
F
R
E
E
Z
E
PIC
-
M
UTE
P
C
C
A
R
D
M
A
G
N
IF
Y
VOL.
SLIDE
F
O
L
D
E
R
SLIDE
LIST
28
E 12
Operating Range
7m
Remote Control Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries' polarity (+/–) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place.
Do not mix different types of batteries or new and old batteries.
Remote Control Precautions
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
If you will not be using the remote control for a long time, remove the
batteries.
Do not place the batteries upside down.
Do not look into the laser pointer while it is on.
Do not point the laser beam at a person.
E 13
Switching operation mode between mouse and projector
The three shaded buttons shown on the drawing work as a computer mouse in the Computer mode.
In the Computer mode the PJ button is not lit.
When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode, which allows the projector menu
operation using the three buttons.
When the POINTER button is pressed, the PJ button lights red to indicate that you are in the Projector mode and that the MOUSE ▲▼
button
works as a moving button for the POINTER or magnified image.
If no buttons are pressed within 10 seconds, the PJ button's light goes out to indicate that you are in the Computer mode. To enable the projector
menu operation again, press the PJ button to light red. To move the pointer or a magnified image again, turn off the pointer and then turn on the
pointer (press the POINTER button two times).
When the PJ button is lit, if you want to use the mouse function immediately, press the PJ button to return to the Computer mode (not lit).
KEYSTONE
FREEZE
PIC
-
MUTE
HELP
POINTER
PC CARD
VIDEO S
-
VIDEO
AUTO ADJ.
RGB 1
MENU LASER
R-CLICK /CANCEL
L-CLICK/ENTER
RGB 2 P
J
ONOFF
MAGNIFY
VOL.
SLIDE
FOLDER
SLIDE
LIST
KEYSTONE
FREEZE
PIC
-
MUTE
HELP
POINTER
PC CARD
VIDEO S
-
VIDEO
AUTO ADJ.
RGB 1
MENU LASER
R-CLICK /CANCEL
L-CLICK/ENTER
RGB 2 P
J
ONOFF
MAGNIFY
VOL.
SLIDE
FOLDER
SLIDE
LIST
Not lit
Works as a mouse for your computer.
Works as a right-click button
for your computer.
Works as a left-click button
for your computer.
Lit red
Works as the Select button
on the projector.
Works as the Cancel
button on the projector.
Works as the Enter
button on the projector.
E 14
2. INSTALLATION
This section describes how to set up your MultiSync MT1055/MT1050/
MT850 projector and how to connect video and audio sources.
Setting up Your Projector
Your MultiSync MT1055/MT1050/MT850 Projector is simple to set up
and use. But before you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you
can project your image.
Carrying the Projector: Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video
sources are disconnected before moving the projector.
When moving the projector or when it is not in use, cover the lens with
the lens cap.
Carrying handle
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE
AUTO ADJUST
U
S
B
AC IN
Attaching the lens cap to the lens hood
with the supplied string and rivet.
Selecting a Location
The further your projector is from the screen or wall, the larger the
image. The minimum size the image can be is approximately 30" (0.76
m) measured diagonally when the projector is roughly 4 feet (1.3 m)
from the wall or screen. The largest the image can be is 300" (7.6 m)
when the projector is about 36.8 feet (11.2 m) from the wall or screen.
Using a Tabletop or Cart
1. Place your projector on a flat level surface at the optimal dis-
tance from the screen or wall so you realize the size image you
want.
(Avoid having bright room lighting or sun light directly on the screen
or wall where youll be projecting the image.)
2. Connect the power cable, remove the lens cap and turn the pro-
jector on. (If no input signal is available, the projector will display a
background image.)
3. Ensure that the projector is square to the screen.
Lens cap
String
4. Move the projector left or right to center the image horizontally
on the screen.
5. To center the image vertically, lift the front edge of the projector
and press the One-Touch Tilt button on the front-left side of the
projector to release the Front Adjustable foot.
Top view
Screen
(There is approximately 5 degrees of up and down adjustment for the front
of the projector.)
6. If the projected image does not appear square to the screen then
use keystone correction for proper adjustment.
7. Adjust the size of the image using the Zoom ring on the lens.
Side view
Screen
AC IN
Rivet
E 15
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWE
R
STATUS
ON
/
OFF
SOURCE
AUTO ADJUST
A
C
I
N
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
L
E
C
T
P
O
W
E
R
S
T
A
T
U
S
O
N
/
O
F
F
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
A
C
I
N
Adjusting the Tilt Foot
Press and hold the Tilt button on the left side of the projector.
Lift the front edge of the projector to the height you want, and release
the button to lock the Adjustable Tilt Foot.
To fine-tune the images position vertically on the screen, rotate the
foot. Each of the rear feet height can be changed up to 0.6 (4mm).
E 16
Ceiling Installation
Screen top
2.9” (79.5mm)
Lens Center
Screen center
Screen Bottom
Throwing Distance (C)
Throwing Angle (α)
Projector Foot
D
B
WARNING
Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more information.
* Do not attempt to install the projector yourself.
Only use your projector on a solid, level surface. If the projector
falls to the ground, you can be injured and the projector se-
verely damaged.
Do not use the projector where temperatures vary greatly. The
projector must be used at temperatures between 32˚F (0˚C)
and 104˚F (40˚C).
Do not expose the projector to moisture, dust, or smoke. This
will harm the screen image.
Ensure that you have adequate ventilation around your projec-
tor so heat can dissipate. Do not cover the vents on the side or
the front of the projector.
If your projector is mounted on the ceiling and your image is upside
down, use the Menu and Select buttons on your projector cabinet or
▲▼ button on your remote control to correct the orientation. (See page
E-36.)
Reflecting the Image
Using a mirror to reflect your projectors image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror. If
youre using a mirror and your image is inverted, use the Menu and
Select buttons on your projector cabinet or ▲▼ buttons on your re-
mote control to correct the orientation. (See page E-36.)
Distance Chart
Throwing Angle (α)
Throwing Distance (C)
2.9” (79.5mm)
Lens Center
Screen top
Screen center
Screen Bottom
D
B
Projector Foot
B=Vertical distance between lens center and screen center
C=Throw distance
D=Vertical distance between lens center and screen bottom (screen top for ceiling installation)
E 17
10.3
10.1
10.1
10.0
10.0
10.0
10.0
9.9
9.9
9.9
9.8
9.8
9.8
9.8
Diagonal
Width Height wide telephoto wide telephoto
B
C
Screen Size
D α
40
1016
60
1524
67
1701.8
72
1828.8
84
2133.6
90
2286
100
2540
120
3048
150
3810
180
4572
210
5334
240
6096
270
6858
300
7620
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
32
812.8
48
1219.2
53.6
1361.44
57.6
1463.04
67.2
1706.88
72
1828.8
80
2032
96
2438.4
120
3048
144
3657.6
168
4267.2
192
4876.8
216
5486.4
240
6096
24
609.6
36
914.4
40.2
1021.08
43.2
1097.28
50.4
1280.16
54
1371.6
60
1524
72
1828.8
90
2286
108
2743.2
126
3200.4
144
3657.6
162
4114.8
180
4572
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
10.2
259.5
15.3
389.2
17.1
434.7
18.4
467.1
21.5
544.9
23.0
583.9
25.5
648.7
30.6
778.5
38.3
973.1
46.0
1167.7
53.6
1362.3
61.3
1557.0
69.0
1751.6
76.6
1946.2
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
56.3
1430.3
86.1
2185.8
96.5
2450.2
103.9
2639.0
121.7
3092.3
130.7
3318.9
145.5
3696.6
175.3
4452.1
219.9
5585.2
264.5
6718.4
309.1
7851.5
353.7
8984.7
398.3
10117.8
443.0
11251.0
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
68.6
1743.7
104.3
2649.9
116.8
2967.1
125.7
3193.7
147.1
3737.4
157.8
4009.3
175.7
4462.4
211.4
5368.7
264.9
6728.0
318.4
8087.4
371.9
9446.8
425.4
10806.2
479.0
12165.5
532.5
13524.9
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
1.8
45.3
2.7
68.0
3.0
75.9
3.2
81.5
3.7
95.1
4.0
101.9
4.5
113.3
5.4
135.9
6.7
169.9
8.0
203.9
9.4
237.9
10.7
271.8
12.0
305.8
13.4
339.8
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
8.5
8.4
8.3
8.3
8.3
8.3
8.3
8.3
8.2
8.2
8.2
8.2
8.2
8.2
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
40
1016
60
1524
67
1701.8
72
1828.8
84
2133.6
90
2286
100
2540
120
3048
150
3810
180
4572
210
5334
240
6096
270
6858
300
7620
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
32
812.8
48
1219.2
53.6
1361.44
57.6
1463.04
67.2
1706.88
72
1828.8
80
2032
96
2438.4
120
3048
144
3657.6
168
4267.2
192
4876.8
216
5486.4
240
6096
24
609.6
36
914.4
40.2
1021.08
43.2
1097.28
50.4
1280.16
54
1371.6
60
1524
72
1828.8
90
2286
108
2743.2
126
3200.4
144
3657.6
162
4114.8
180
4572
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
10.2
259.5
15.3
389.2
17.1
434.7
18.4
467.1
21.5
544.9
23.0
583.9
25.5
648.7
30.6
778.5
38.3
973.1
46.0
1167.7
53.6
1362.3
61.3
1557.0
69.0
1751.6
76.6
1946.2
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
56.5
1434.7
85.8
2179.8
96.1
2440.5
103.4
2626.8
121.0
3073.8
129.8
3297.3
144.5
3669.8
173.8
4414.9
217.8
5532.4
261.8
6650.0
305.8
7767.6
349.8
8885.1
393.8
10002.7
437.8
11120.3
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
68.2
1732.7
103.4
2626.7
115.7
2939.7
124.5
3163.2
145.7
3699.6
156.2
3967.8
173.8
4414.8
209.0
5308.9
261.8
6649.9
314.6
7991.0
367.4
9332.0
420.2
10673.1
473.0
12014.1
525.8
13355.2
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
1.8
45.3
2.7
68.0
3.0
75.9
3.2
81.5
3.7
95.1
4.0
101.9
4.5
113.3
5.4
135.9
6.7
169.9
8.0
203.9
9.4
237.9
10.7
271.8
12.0
305.8
13.4
339.8
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
10.3
10.1
10.1
10.1
10.1
10.0
10.0
10.0
10.0
10.0
9.9
9.9
9.9
9.9
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
8.5
8.4
8.4
8.4
8.4
8.4
8.4
8.3
8.3
8.3
8.3
8.3
8.3
8.3
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
Diagonal
Width Height wide telephoto wide telephoto
B
C
Screen Size
D α
40
1016
60
1524
67
1701.8
72
1828.8
84
2133.6
90
2286
100
2540
120
3048
150
3810
180
4572
210
5334
240
6096
270
6858
300
7620
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
32
812.8
48
1219.2
53.6
1361.44
57.6
1463.04
67.2
1706.88
72
1828.8
80
2032
96
2438.4
120
3048
144
3657.6
168
4267.2
192
4876.8
216
5486.4
240
6096
24
609.6
36
914.4
40.2
1021.08
43.2
1097.28
50.4
1280.16
54
1371.6
60
1524
72
1828.8
90
2286
108
2743.2
126
3200.4
144
3657.6
162
4114.8
180
4572
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
10.3
261.6
15.4
392.3
17.2
438.1
18.5
470.8
21.6
549.3
23.2
588.5
25.7
653.9
30.9
784.7
38.6
980.8
46.3
1177.0
54.1
1373.2
61.8
1569.3
69.5
1765.5
77.2
1961.7
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
57.0
1446.5
86.5
2197.5
96.9
2460.3
104.3
2648.1
122.0
3098.6
130.9
3323.9
145.6
3699.4
175.2
4450.4
219.6
5576.8
263.9
6703.2
308.3
7829.6
352.6
8956.1
396.9
10082.5
441.3
11208.9
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
68.8
1746.9
104.3
2648.0
116.7
2963.4
125.5
3188.7
146.8
3729.4
157.5
3999.7
175.2
4450.3
210.7
5351.4
263.9
6703.1
317.1
8054.8
370.3
9406.5
423.6
10758.2
476.8
12109.9
530.0
13461.6
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
1.7
43.2
2.6
64.9
2.9
72.4
3.1
77.8
3.6
90.8
3.8
97.3
4.3
108.1
5.1
129.7
6.4
162.2
7.7
194.6
8.9
227.0
10.2
259.5
11.5
291.9
12.8
324.3
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
10.2
10.1
10.1
10.1
10.1
10.0
10.0
10.0
10.0
10.0
9.9
9.9
9.9
9.9
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
8.5
8.4
8.4
8.4
8.4
8.4
8.4
8.3
8.3
8.3
8.3
8.3
8.3
8.3
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
degree
Diagonal
Width Height wide telephoto wide telephoto
B
CScreen Size D α
MT850
MT1050
MT1055
NOTE: Distances may vary +/5%.
E 18
PC CONTROL
REMOTE
CONTROL
INPUT
MOUSE
OUTPUT
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
Wiring Diagram
NOTE: When using with a notebook PC, be sure to connect between the projec-
tor and the notebook PC before turning on the power to the notebook PC. In
most cases signal cannot be output from RGB output unless the notebook PC
is turned on after connecting with the projector.
NOTE: If using video, S-video, or audio cables, the cables should be 3 m (9.8
feet) or shorter.
Remote Control Guideline for the Remote Control
1. Plug the supplied serial cable with the mouse output port of the pro-
jector into your computers mouse port and restart your computer to
gain remote mouse control.
2. When using the remote controls built-in infrared mouse on a laptop
computer, the laptops mouse, trackball or trackpad will be disabled.
Disconnect the serial cable from the mouse output port and restart
your computer to regain trackball or trackpad mouse control.
3. If the screen goes blank while using your remote control, it may be
the result of the computers screen-saver or power management
software.
4. If you accidentally hit the OFF button on the remote control, wait one
full minute and then press the ON button to resume.
Supplied serial cable
Supplied mouse adapter
(For Macintosh or USB)
Supplied mouse adapter
(For IBM PS/2 or USB)
Macintosh or Compatibles
(Desktop type or notebook type)
IBM VGA or Compatibles
(Desktop type or notebook type)
Signal cable (supplied)
To mini D-Sub 15-pin connector on the
projector. It is recommended that you
use a commercially available distribu-
tion amplifier if connecting a signal
cable longer than the supplied one.
DVD Player (with component output)
Optional Component V cable
Document Camera
To video, S-video, and audio
inputs on the projector.
VCR, DVD Player or LaserDisc Player
Monitor
Connecting Your PC or Macintosh Computer
Connecting your PC or Macintosh computer to your MultiSync MT1055
and MT1050 (XGA) / MT850 (SVGA) projector will enable you to project
your computers screen image for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the signal cable thats supplied to connect your PC or Macintosh
computer to the projector.
NOTE:The new Macintosh computer such as G3 will have the 15 pin HD
connector. The MT1055/MT1050/MT850's "Plug and Play" data will be down-
loaded to the Macintosh. Therefore, the Mac adapter will not be necessary.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be caused
by a screen saver installed on the computer youve connected to the
projector.
E 19
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
L
E
C
T
P
O
W
E
R
S
T
A
T
U
S
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
A
C
I
N
S
-V
IDE
O
VIDE
O
AUD
IO
RG
B INPUT
2
A
U
D
I
O
R
G
B
I
N
P
U
T
1
L
/
M
ON
O
R
A
U
D
I
O
R
G
B
M
O
N
I
T
O
R
O
U
T
P
U
T
U
S
B
P
C
-
C
A
R
D
C
C
O
N
T
R
O
L
M
O
U
S
E
O
U
T
R
E
M
O
C
O
N
T
R
I
N
P
U
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO
RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
RGB INPUT
AUDIO
IBM VGA or Compatibles (Notebook type)
RGB signal cable (supplied)
To mini D-Sub 15-pin connector on the
projector. It is recommended that you
use a commercially available distribu-
tion amplifier if connecting a signal
cable longer than the supplied one.
IBM VGA or Compatibles (Desktop type)
Audio cable (not supplied)
Connecting Your PC
Connecting your PC to your MultiSync MT1055 and MT1050 (XGA)/
MT850 (SVGA) projector will enable you to project your computers
screen image for an impressive presentation.
To connect to a PC, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC to the projector.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be caused
by a screen saver installed on the computer youve connected to the
projector.
E 20
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
STAND BY
SOURCE A
UTO ADJUST
A
C
I
N
S-VIDEO
VIDEO
AUDIO
R
GB IN
PUT 2
A
U
D
I
O
R
G
B
I
N
P
U
T
1
L
/
M
ONO
R
A
U
D
I
O
R
G
B
M
O
N
I
T
O
R
O
U
T
P
U
T
U
SB
PC-
CARD
C
C
O
N
T
R
O
L
M
O
U
S
E
O
U
T
R
E
M
O
C
O
N
T
R
I
N
P
U
S
-V
ID
E
O
V
ID
E
O
A
U
D
IO
R
G
B
IN
P
U
T
2
AUDIO
RGB INPUT 1
L
/
M
O
N
O
R
AUDIO
RG
B MONITOR
OUTPUT
RGB INPUT
AUDIO
Macintosh (Notebook type)
RGB Signal cable (supplied)
Audio cable (not supplied)
1
O
N
D
I
P
2
3
4
56
Pin adapter for Macintosh
(not supplied)
For older Macintosh, use a commercially
available pin adapter to connect to your
Mac's video port.
The new Macintosh computer such as
G3 will have the 15 pin HD connec-
tor. The MT1055/MT1050/MT850's
"Plug and Play" data will be down-
loaded to the Macintosh. Therefore,
a Mac adapter will not be necessary.
Connecting Your Macintosh Computer
To connect to a Macintosh, simply:
1. Turn off the power to your projector and your Macintosh computer.
2. Use the supplied signal cable to connect your Macintosh computer
to the projector.
3. Turn on the projector and the Macintosh computer.
Macintosh (Desktop type)
E 21
External monitor
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
L
E
C
T
P
O
W
E
R
S
T
A
T
U
S
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
A
C
I
N
S
-
V
I
D
E
O
V
I
D
E
O
A
U
D
I
O
R
G
B
I
N
P
U
T
2
A
U
D
I
O
R
G
B
I
N
P
U
T
1
L
/
M
O
N
O
R
A
U
D
I
O
R
G
B
M
O
N
I
T
O
R
O
U
T
P
U
T
U
S
B
P
C
-
C
A
R
D
C
C
O
N
T
R
O
L
M
O
U
S
E
O
U
T
R
E
M
O
C
O
N
T
R
I
N
P
U
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
RGB INPUT
RGB OUTPUT
AUDIO IN
AUDIO OUT
Connecting an External Monitor
You can connect a separate, external monitor to your MT1055/MT1050/MT850 to simultaneously view on a monitor the image you're projecting. To
do so:
1. Turn off the power to your projector, monitor and computer.
2. Use a 15-pin cable to connect your monitor to the RGB Monitor Output (Mini D-Sub 15 pin) connector on your projector.
3. Turn on the projector, monitor and the computer.
PC CONTROL
REMOTE
CONTROL
INPUT
MOUSE
OUT
Serial cable (suppried)
Macintosh
IBM PS2
Connecting Your Computer to the Mouse Output Port
The built-in remote mouse receiver enables you to operate your
computer's mouse functions from the remote control. It is a great con-
venience for clicking through your computer-generated presentations.
To connect the mouse output port:
1. Turn off your computer.
2. For PCs: Remove your current mouse and connect the supplied
serial cable from the mouse output to your PC's mouse port. (Use
the 6-pin adapter for connecting to a PS/2 computer or the supplied
USB adapter.)
For Macintosh: Remove your current mouse from your computer,
attach the Macintosh adapter or the supplied USB adapter to the
mouse output port's serial cable, and connect the projector to your
mouse port.
3. When the built-in remote mouse receiver is available, it will disable
your regular mouse, disconnect the serial cable and restart your
computer.
NOTE: The mouse adapter for USB is not compatible with the USB terminal on
the projector.
RGB Signal cable (suppried)
E 22
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SE
LECT
P
O
W
E
R
ST
AT
U
S
O
N
/
ST
AN
D B
Y
SO
URC
E
AUT
O
AD
J
US
T
A
C
I
N
S-VIDEO
VIDEO
AUDIO
RGB INPUT 2
A
U
D
I
O
R
G
B
I
N
P
U
T
1
L
/
MONO
R
A
U
D
I
O
R
G
B
M
O
N
I
T
O
R
O
U
T
P
U
T
US
B
P
C
-C
A
R
D
C
C
O
N
T
R
O
L
M
O
U
S
E
O
U
T
R
E
M
O
C
O
N
T
R
I
N
P
U
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO
RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
RGB INPUT
Y Cb Cr
R L
R L
Red
White
Y
Cb
Cr
Red
White
DVD player
Optional 15-pin-to-RCAן3 cable (optional)
(Component V )
Audio cable (not supplied)
Audio Equipment
Connecting Your DVD Player
You can connect your projector to a DVD player with component out-
puts or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use
the optional 15-pin-to-RCAן3 cable to connect your DVD player to
the RGB INPUT connector on the projector.
For a DVD player without component video (Y,Cb,Cr) outputs, use
common RCA cables (not provided) to connect a composite VIDEO
output of the DVD player to the Video Input of the projector.
3. Turn on the projector and DVD player.
NOTE: Refer to your DVD players owners manual for more information about
your DVD players video output requirements,
E 23
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
LE
C
T
P
O
W
E
R
S
TA
TU
S
O
N
/
S
T
AN
D
B
Y
S
O
U
R
CE
A
U
TO
A
D
J
U
ST
A
C
I
N
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
A
U
D
I
O
R
G
B
I
N
P
U
T
1
L
/
MONO
R
A
U
D
I
O
R
G
B
M
O
N
I
T
O
R
O
U
T
P
U
T
U
S
B
PC
-C
A
R
D
C
C
O
N
T
R
O
L
M
O
U
S
E
O
U
T
R
E
M
O
C
O
N
T
R
I
N
P
U
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO
RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
VIDEO
S-VIDEO
R L
R L
VIDEO
VCR/ Laser disc player
S-video cable (not supplied)
Audio equipment
Audio cable (not supplied)
Document camera
Video cable (not supplied)
Connecting Your VCR or Laser Disc Player
Use common RCA cables (not provided) to connect your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video
input on your projector. Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio equipment (if your
VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.
3. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owners manual for more information about your equipments video output requirements.
E 24
About Startup screen
(Menu Language Select screen)
When you first turn on the projector, you will get the Startup screen.
This screen gives you the opportunity to select one of the seven menu
languages: English, German, French, Itilan, Spanish,Swedish and Japa-
nese.
To select a menu language, follow these steps:
1. Use the Select or button to select one of the seven languages
for the menu.
2. Press the Enter button to execute the selection.
3. The Basic/Custom menu will be displayed in the language you
have selected.
To close the menu, press the Cancel button.
After this has been done, you can proceed to the advanced menu op-
eration.
If you want, you can select the menu language later. See Language
on page E-35.
E 25
3. OPERATION
This section describes how to select a computer or video source, how
to adjust the picture, and how to customize the menu or projector set-
tings.
General Controls
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
1. Turn on the Projector
Plug the supplied power cable in the wall outlet. The projector
will go into its standby mode and the power indicator will glow
orange.
Only after you press the On button on the remote control (ON/
STAND BY button on the projector cabinet) will the power indi-
cator turn to green and the projector become ready to use.
NOTE: To turn the projector on by plugging in the power cable, use the
menu and enable the Auto Start feature. (See page E-37.)
2. Select the Computer, Video Source or PC Card Viewer
Press a source button on the remote control or the projector cabi-
net to select Video (VCR, document camera, or laser disc
player), S-Video, RGB 1 or 2 (computer or DVD with compo-
nent output) or PC Card Viewer to display the image.
Or press the Menu button on the remote control or the cabinet
and use the menu to select your video source: Video, S-Video,
RGB1 or 2, or PC Card Viewer.
3. Adjust the Image Size and the Focus
Use the Zoom ring to adjust the image size, then use the Focus
ring to obtain the best focus.
Use the Magnify button (+) or (-) on the remote control to make
the image larger up to 400%.
4. Turning off the Projector
First press the off button on the remote control (ON/STAND
BY button on the projector cabinet) for a minimum of two sec-
onds. The power indicator will glow orange. Then, unplug the
power cable. The power indicator will go out.
IMPORTANT:
The projector should be unplugged if it will not to be used for an
extended period.
To turn off the image and sound briefly (five minutes or less), use
the Picture Mute button instead of turning the projector off and on.
The projector will display a black, blue image or logo if no input sig-
nal is present.
Do not turn the projector off and then immediately back on. The
projector needs to cool for a minute before it can be restarted.
After the projector turns off, the cooling fans keep operating for a full
minute.
Do not disconnect the power cable during this time.
Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced
motion video image is projected.
1. Press the Menu button on the remote control or projector cabi-
net to display the Main Menu.
NOTE: When using a USB mouse, click the mouse button to display the
main menu. For other operations, do the same way as you use your PC
mouse.
2. Press the ▲▼ buttons on the remote control or the projector cabi-
net to highlight the menu for the item you want to adjust or set.
3. Press the
button or the Enter button on the projector cabinet
or the Left Click button on the remote control to select a submenu
or item.
4. Adjust the level or turn the selected item on or off by using Se-
lect
or
buttons on the cabinet, or the Mouse button on the
remote control. The on-screen slide bar will show you the amount
of increase or decrease.
5. Changes are stored until you adjust it again.
ENTER ......... Stores the setting or adjustments.
CANCEL ..........
Return to the previous screen without storing settings or ad-
justments.
NOTE: You can close the main and sub menus simultaneously by pressing
the PJ button to cancel the Projector mode.
6. Repeat steps 2-5 to adjust an additional item, or press Cancel
on the projector cabinet or the remote control to quit the menu
display.
Using a USB Mouse
Using a USB mouse gives you a smooth operation. A commercially
available USB mouse is required.
NOTE: There may be some brands of USB mouse that the projector does not
support.
Operate the Menus using the USB mouse:
Mouse Cursor:
When connecting a USB mouse to the projector, you get a mouse
cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse
cursor disappears.
Menu Display:
Clicking with a mouse button displays the main menu.
Clicking displays the pull-down menu.
To close the menu, click anywhere in the background.
Adjusting and Setting Display:
You can select a menu item and click with a mouse button to make
adjustments and setting.
Examples:
Click (or press and hold) the mouse button
or
to adjust the
brightness.
Or click and drag the mouse button on the slide bar horizontally to
adjust it.
To save the adjustments, click . The display is closed.
If you click anywhere in the background while displaying adjust-
ment and setting menu or dialog box, you will get the main menu at
the clicking point.
NOTE: The MOUSE OUTPUT port on the projector is not compatible with the
USB mouse.
E 26
Source display
SOURCE AUTO ADJUST
Each time the Source button is pressed, the input source will change
as follows:
RGB1 RGB2 Video S-Video PC Card Viewer
If no input signal is present, the input will be skipped.
Press the Auto Adjust button to fine-tune the computer image or to
remove any vertical banding that might appear and to reduce video
noise, dot interference or cross talk (this is evident when part of your
image appears to be shimmering). This function adjusts the clock fre-
quencies that eliminate the horizontal banding in the image. This func-
tion also adjusts the clock phase to reduce video noise, dot interfer-
ence or cross talk. (This is evident when part of your image appears to
be shimmering.)
This adjustment may be necessary when you connect your computer
for the first time.
NOTE: The Auto Adjust function does not work for component signal.
Basic Operation
Selecting the computer or video source:
Adjust the Image Using Auto Adjust
The Auto Adjust function automatically optimizes the image in RGB
mode.
VIDEO S
-
VIDEO
AUTO ADJ.
RGB 1
MENU LASER
RGB 2 P
J
ONOFF
AUTO ADJUST
HELP
POINTER
PC CARD
AUTO ADJ.
VIDEO S
-
VIDEO
RGB 1 RGB 2
P
J
[Poor picture]
[Normal picture]
E 27
Volume control:
Sound level from the speaker on the projector can be adjusted.
increase volume
VOL.
Volume bar
decrease volume
Turning off picture and sound:
Press the Picture Mute button to turn off the image and sound for a
short period of time. Press again to restore the image and sound.
PIC
-
MUTE
Getting Help about how to operate the projector:
You get the contents about Help.
Display Help
MENU LASER
R-CLICK /CANCEL
Exit Help
Using Pointer
You can use one of eight pointers to draw your audience's attention to
the portion of a projected image you want.
Press the Pointer button to
display the pointer.
Use the Select button to
move the pointer.
Enlarging and Moving a Picture
You can enlarge the area you want up to 400 percent.
To do so:
1. Press the Pointer button to display the pointer.
2. Move the pointer to the area you want to enlarge.
3. Enlarge the selected area.
When the Magnify (+) button is pressed, the pointer is changed to
a magnifying glass. To move the magnifying glass, use the Mouse
button.
MAGNIFY
HELP
POINTER
POINTER
E 28
Customizing Basic/Custom Menu
The Basic/Custom menu can be customized to meet your requirements.
Selecting a menu item from the Basic/Custom Menu Edit list, allows
you to custom tailor the menu items to your needs.
1. Select Basic/Custom Menu Edit to display the Basic/Custom
Menu Edit screen.
2. Use the or button to highlight your selection and press the
Enter button to place a check mark next to an option. This action
enables that feature.
Press the Enter button again to clear the check box.
If you select an item with a solid triangle
and press the Enter
button on the remote control or the projector cabinet, you can
enable all the items within that submenu.
Also you can turn on an item within the submenu without placing
a check mark on the main menu item.
NOTE: Up to 12 main menu items (within Basic/Custom Menu Edit, not
including submenu items) can be selected.
4. Return the image to the original size.
Correcting Keystone distortion
Press (+) or (-) to correct keystone (trapezoidal) distortion to make the
top or bottom of the screen longer or shorter so that the projected
image is rectangular.
KEYSTONE
NOTE: The maximum keystone angle that can be corrected is 40 degrees up-
ward and 20 degrees downward with the projector placed horizontally on the
ground plane.
Depending on the type of graphics being used, the picture may get blurred or
keystone correction may not be possible when excessive keystone correction
is used.
The idea is, the closer you are to native resolution, the better image you will
see.
Freezing a picture
Press the Freeze button to freeze a picture. Press again to resume
motion.
Keystone distortion Normal
MAGNIFY
FREEZE
E 29
3. In order for the changes to take effect, use the
or
button on
the remote control or the projector cabinet to highlight OK,
then press the Enter button. To cancel the changes, use the or
buttons to highlight Cancel and press the Enter button.
To return to the factory default, select Reset then press the En-
ter button.
The default Basic/Custom Menu items are:
Source Select (RGB1/2, Video, S-Video and PC Card Viewer), Pic-
ture, Volume, Image Options (Keystone, Color Temperature and
Lamp Mode), Projector Options (Menu and Setup), Tools (Capture,
PC Card Files and ChalkBoard) and Help (Contents and Informa-
tion)
NOTE: Once you have selected OK on the Basic/Custom Menu Edit screen, you
cannot cancel the changes on the Menu screen. However, you can re-edit the
menu items over again as described in the steps above.
NOTE: If the Advanced Menu item has been selected on the Menu mode, you
get the Confirmation Change Menu upon completion of Basic/Custom Menu
editing. In this case, selecting Yes then Enter will close all the menus and
apply the changes from the Advanced menu to the Basic/Custom Menu. If you
select No then Enter functions, then all menu items will return to the Ad-
vanced menu, but your changes will still be available within the Basic/Custom
Menu selection. To display the previously tailored Basic/Custom Menu, select
Basic/Custom Menu from the Menu Mode.
An item To Advanced Menu will be added to the bottom of the Basic/
Custom Menu.
Selecting this item and pressing the Enter button will display the Ad-
vanced Menu features.
E 30
Menu Tree
Advanced Menu
Source Select RGB2
RGB1
Picture Video
Volume S-Video Brightness/Contrast/Color/Hue/Sharpness
Image Options PC Card Viewer
Projector Options
Volume
High-Bright/Eco
Tools
Help Keystone
Normal/Natural 1/Natural 2
Color Temperature
Lamp Mode
Gamma Correction
Aspect Ratio Normal/Zoom/Wide Zoom/Cinema
Advanced Options
Noise Reduction Off/Low/Medium/High
Factory Default
Color Matrix Select Color Matrix HDTV/SDTV
Select Color Matrix Type B-Y/R-Y,Cb/Cr,Pb/Pr
White Balance Brightness R/G/B, Contrast R/G/B
Position/Clock Horizontal/Vertical/Clock/Phase
Resolution Auto/Native
Video Filter On/Off
All Data/Current Signal
Menu
Setup
Menu Mode (Advanced Menu, Basic/Custom Menu)
Basic/Custom Menu Edit
Language (English/German/French/Italian/Spanish/Swedish/Japanese)
Projector Pointer (Pointer 1-8)
Source Display (On/Off)
Direct Button Volume Bar (On/Off)
Keystone Bar (On/Off)
Menu Display Time (Manual/Auto 5 sec/Auto 10 sec/Auto 30 sec)
Orientation (Desktop Front/Ceiling Rear/Desktop Rear/Ceiling Front)
Background (Blue/Black/Logo)
Mouse Button(Right Hand/Left Hand)
Sensitivity(Fast/Medium/Slow)
PC Card Viewer Options Show Folder List (On/Off)
(Auto Play/Manual Play)
Interval (5-300 sec)
Capture Options (High Quality/Normal/High Compression)
Signal Select RGB1 (Auto/RGB/Component)
RGB2 (Auto/RGB/Component)
Video (Auto/NTSC3.58/NTSC4.43/PAL/PAL60/SECAM)
S-Video (Auto/NTSC3.58/NTSC4.43/PAL/PAL60/SECAM)
Auto Adjust (RGB Only) (On/Off)
Auto Start (On/Off)
Power Management (On/Off)
Power Off Confirmation (On/Off)
Keystone Save (On/Off)
Fan High Speed Mode (On/Off)
Auto Mute for Built-in Speaker (On/Off)
Clear Lamp Hour Meter
Remote Sensor (Front/ Back/ Left/ Right)
S-Video Mode Select (Off/S2)
RGBOUT Terminal (Disable/ RGB1/ RGB2)
Communication Speed(4800/9600/19200/38400)
Default Source Select (Last/Auto/Select)
(RGB1/RGB2/Video/S-Video/PC Card Viewer)
Capture
PC Card Files
ChalkBoard
Contents Contents
Information Page1 Source Name/Input Terminal/Horizontal Frequency/Vertical Frequency/Sync Polarity
Page2 Signal Type/Video Type/Sync Type/Interlace/Resolution
Page3 Aspect Ratio/Gamma Correction/Noise Reduction/Color Matrix/Matrix Type
Pa
g
e4 Lam
p
Remainin
g
Time/Lam
p
Hour Meter/Pro
j
ector Usa
g
e
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
E 31
Menu windows or dialog boxes typically have the following elements:
Title bar: Indicates the menu title.
Highlight: Indicates the selected menu or item.
Solid triangle: Indicates further choices are available. A highlighted triangle indicates the item is active.
Tab: Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button: Use this round button to select an option in a dialog box.
Check box: Place a checkmark in the square box to turn the option On.
Slide bar: Indicates settings or the direction of adjustment.
OK button: Press to confirm your setting. You will return to the previous menu.
Cancel button: Press to cancel your setting. You will return to the previous menu.
Close button: Click to close the window with saving changes. (USB mouse only)
Help button: Indicates that help about that feature is available (USB mouse only). Press the Help button on the remote control to display help.
Toolbar: Contains several icons for specific tasks. It is also referred to as "launcher".
Drag: Point the mouse here, and click and drag to move a toolbar.
Menu Elements
Title bar
Tab
Highlight
Help Button
Close Button
OK Button
Cancel Button
Solid triangle
Radio button
Slide bar
Check box
Drag
Tool bar
E 32
The launcher is a tool bar including the following buttons:
Drag ............. Drags to move the tool bar. (for USB mouse operation only)
Prev ............. Returns to the previous slide or folder.
Next ............. Advances to the next slide or folder.
Play .............. Plays back automatically or manually depending on the set-
ting on PC Card Viewer Options of the menu. This allows you
to move on to the next slide when "Manual Play" is selected.
Stop ............. Stops Auto Play while you are playing back and to resume
playing from the selected slide or folder when "Auto Play" is
selected.
Jump ........... Displays a list of slides while you are playing back.
Select ........... Displays a list of folders while you are playing back.
Setup ........... Displays the PC Card Viewer Options dialog box on Page 2 of
the Setup dialog box.
Delete ........... Deletes a captured slide(s) or all the captured slides in the
selected folder.
View ............. Hides the tool bar while you are playing back. Clicking with
the right button of a mouse shows it again.
Picture (not available for PC Card Viewer)
Menu Descriptions & Functions
Source Select
Enables you to select a video source such as a VCR, DVD player, laser
disc player, computer or document camera depending on what is con-
nected to your inputs.
Press the "Select" button on the projector cabinet or ▲▼ buttons on
your remote control to highlight the menu for the item you want to ad-
just.
RGB1 / RGB2
Selects the computer connected to your RGB or component signal.
NOTE: An optional component cable (Component V cable) is needed for a com-
ponent signal. Select "Component" from the Input Signal submenu to display
the component signal.
Video
Selects what is connected to your Video input-VCR, laser disc player,
DVD player or document camera.
S-Video
Selects what is connected to your S-Video input-VCR, DVD player, or
laser disc player.
NOTE: A frame may freeze for a brief period of time when a video is played back
in fast-forward or fast-rewind with a Video or S-Video source.
PC Card Viewer
This feature enables you to make presentations using a PC card that contains
captured images and slides created with the exclusive PC Card Viewer Utility
contained in the CD-ROM. See page E-41 for installing the PC Card Viewer
Utility. The starting screen for the PC Card Viewer varies depending on the
settings of the Setup's Page 2. See Setup on page E-36.
NOTE: Even if you switch the current PC Card Viewer source to another source,
the current slide is retained. When you return back to the PC Card Viewer, you
will get the slide that has been retained. A launcher will appear when you press
the MENU button.
A press of the MENU button displays the toolbar; a press of the MENU
button again displays the Menu and hereafter each press of the MENU
button switches displaying between the Menu and the toolbar.
Provides access to controls for your image. Use ▲▼ buttons on the
projector cabinet or the remote control to highlight the menu for the
item you want to adjust.
Brightness ... Adjusts the brightness level or the back raster intensity.
Contrast ....... Adjusts the intensity of the image according to the incoming
signal.
Color ............ Increases or decreases the color saturation level (not valid
for RGB).
Hue .............. Varies the color level from +/- green to +/-blue. The red level
is used as reference. This adjustment is only valid for Video
and Component inputs (not valid for RGB).
Sharpness .... Controls the detail of the image for Video (Not valid for RGB
and Component).
Volume (not available for PC Card Viewer)
Adjusts the sound level of the projector.
NOTE: You can also display the volume bar without opening the menu. See
"Volume Bar (Direct Button)"on page E-35 for more details.
Drag
Prev Play Jump Setup View
Next Stop Select Delete
E 33
Image Options
Keystone
This feature corrects the keystone (trapezoidal) distortion to make
the top of the screen longer or shorter to be the same as the bottom.
Use the
or
buttons on the slide bar to correct the keystone
(trapezoidal) distortion.
Keystone distortion
Normal
NOTE: The maximum keystone angle that can be corrected is 40 degrees up-
ward and 20 degrees downward with the projector placed horizontally on the
ground plane.
Depending on the type of graphics being used, the picture may get
blurred or keystone correction may not be possible when excessive
keystone correction is used.
The idea is, the closer you are to native resolution, the better image
you will see.
Color Temperature
This feature adjusts the color temperature using the slide bar.
Move the slide bar to the right to increase the color temperature for a
bluish image; to the left to decrease it for a reddish image.
Lamp Mode
Gamma Correction
Use the
or
button to choose "Normal" when in a lighted room and
"Natural 1&2" when in a darkened room. "Natural 1" for better flesh
tone; "Natural 2" for true reproduction of middle tones.
Each mode is recommended for :
Normal ......... For the regular picture
Natural 1 ...... For true color reproduction of natural tones
Natural 2 ...... For dark portions of a picture
Aspect Ratio (not available for RGB and PC Card Viewer)
Aspect Ratio allows you to select the best Aspect mode to display your
source image.
When 4:3 is selected from the source (i.e. DVD player), the following
selections will display:
Standard
4:3 Aspect
All 4 sides
stretched
Left & Right
stretched
Left and right
stretched
16:9 image
displayed
in 4:3 mode
All 4 sides
stretched
Normal Zoom Wide Zoom Cinema
Normal Zoom Wide Zoom Cinema
Left & right
stretched
Left and right
stretched to
display the true
aspect
This feature enables you to select two brightness mode of the lamp:
High-Bright and Eco modes. The lamp life can be extended up to 2500
hours by using the Eco mode.
High-Bright Mode ....... This is the default setting.
Eco Mode .................... Select this mode to increase the lamp life.
NOTE: If you have selected the Eco mode, the lamp lights in High-Bright mode
for 3 minutes after the projector is turned on. After 3 minutes the lamp will
change to Eco mode.
When 16:9 is selected from the source (i.e. DVD player), the following
selections will display:
E 34
Noise Reduction (not available for RGB and PC Card Viewer)
You can select three levels video noise reduction.
NOTE: The lower the Noise Reduction level, the better the image quality by way
of higher video bandwidth.
Color Matrix (available for component video signal only)
First select an appropriate color matrix to fit your component signal for
HDTV or SDTV. Then select an appropriate matrix type from B-Y/R-Y,
Cb/Cr or Pb/Pr.
White Balance
This allows you to adjust the white balance. Brightness for each color
(RGB)is used to adjust the black level of the screen;
Contrast for each color (RGB)to adjust the white level of the screen.
First use the or buttons to select R, G, or B for the brightness and
the contrast. Next use the
or
buttons to adjust the level.
Position/ Clock (when Auto Adjust is off)
This allows you to manually adjust the image horizontally and verti-
cally, and adjust Clock and Phase.
Horizontal/Vertical Position
.................... Adjusts the image location horizontally and vertically using
the
and
buttons.
This adjustment is made automatically when the Auto Adjust
is turned on.
Clock ............ Use this item to fine tune the computer image or to remove
any vertical banding that might appear. This function adjusts
the clock frequencies that eliminate the horizontal banding in
the image.
Press the
and
buttons until the banding disappears.
This adjustment may be necessary when you connect your
computer for the first time. This adjustment is made auto-
matically when the Auto Adjust is turned on.
Phase ........... Use this item to adjust the clock phase or to reduce video
noise, dot interference or cross talk. (This is evident when
part of your image appears to be shimmering.) Use the
and
buttons to adjust the image.
See "Auto Adjust (RGB Only) on page E-37 for turning on or off the
Auto Adjust feature.
Use "Phase" only after the "Clock" is complete.
This adjustment is made automatically when the Auto Adjust is turned
on.
Resolution (when Auto Adjust is off)
This allows you to activate or deactivate the Advanced AccuBlend fea-
ture.
Auto ............. Turns on the Advanced AccuBlend feature. The projector au-
tomatically reduces or enlarges the current image to fit the
full screen.
Native ........... Turns off the Advanced AccuBlend feature. The projector dis-
plays the current image in its true resolution.
See "Auto Adjust (RGB Only) on page E-37 for turning on or off the
Auto Adjust feature.
NOTE: While you are displaying an image with higher resolution than the
projector's native resolution, even when you are in the Native mode, the image
is displayed full screen using the Advanced AccuBlend feature.
Video Filter (when Auto Adjust is off)
This function reduces video noise.
On ................ The low-pass filter is applied.
Off ................ The filter is removed.
Screen adjustments are possible even when the filter is On.
E 35
Factory Default
Changes all adjustments and setting to the factory preset for each
source individually except Lamp Hour Meter, Projector Usage, Lan-
guage and Communication Speed. (To reset the lamp usage time, see
"Clear Lamp Hour Meter" on page E-37.)
All Data ............... Reset all the adjustments and settings for all the signals
to the factory preset.
Current Signal ..... Resets the adjustments for the current signal to the fac-
tory preset levels.
The items that can be reset for the currently projected image are:
Picture (Brightness, Contrast, Color, Hue and Sharpness) and Image
Options (Color Temperature, Gamma Correction, Advanced Options
[Aspect Ratio, Noise Reduction, Color Matrix, White Balance, Posi-
tion/Clock, Resolution and Video Filter] ).
NOTE: The Volume, Keystone, Lamp Mode and all the items in the Projector
Options can be reset only when "All Data" is selected.
Projector Options
Allows you to set preferences for the on-screen menu.
Press OK to save your changes for all the features.
Menu Mode:
This feature allows you to select two menu modes: Advanced Menu
and Basic/Custom Menu.
Advanced Menu .......... This is the menu that contains all the available menus
and commands.
Basic/Custom Menu ....This is the menu that you can customize using the
Basic/Custom Menu Edit to fit your needs.
The factory default Basic/Custom menu includes:
Source Select (RGB1/2, Video, S-Video and PC Card Viewer), Picture,
Volume, Image Options (Keystone, Color Temperatureand and Lamp Mode),
Projector Options (Menu and Setup), Tools (Capture, PC Card Files and
ChalkBoad) and Help (Contents and Information). See page E-28 for in-
structions about how to customize the Basic/Custom Menu.
Language:
You can choose one of seven languages for on-screen instructions.
The options are: English, German, French, Italian, Spanish, Swed-
ish and Japanese.
Projector Pointer:
This enables you to select from eight different Pointer icons for the
"Pointer" button on your remote control.
After moving your Pointer icon to the area you want on the screen,
press the Magnify button on the remote control to enlarge the se-
lected area on the screen. See page E-27 for more details.
NOTE: There may be cases where the Pointer function is not available (ex. a
non-interlace signal at 15kHz such as video game.)
Source Display:
You can turn on and off the information for input name such as
VIDEO and RGB.
When this option is on, the current input will be displayed each time
you switch sources or turn on the projector.
Direct Button:
Volume Bar: This option turns on or off the volume bar when you adjust
the sound volume using VOL+/ button on the remote control.
On ................ You can increase or decrease the sound volume with the vol-
ume bar on screen.
Off ................ You can increase or decrease the sound volume without hav-
ing to use the volume bar.
Keystone Bar: This option turns on or off the keystone bar when you ad-
just the keystone using KEYSTONE +/ button on the remote control.
On ................ You can increase or decrease the level with the keystone bar
on screen.
Off ................ You can increase or decrease the level without having to use
the keystone bar.
Menu Display Time :
This option allows you to select how long the projector waits after
the last touch of a button to turn off the menu.
The preset choices are "Manual", "Auto 5 sec", "Auto 10 sec", and
"Auto 30 sec". The "Auto 10 sec" is the factory preset.
Manual ......... The menu can be turned off manually.
Auto 5 sec .... The menu will automatically be turned off in 5 seconds if no
buttons are pressed within 5 seconds.
Auto 10 sec .. The menu will automatically be turned off in 10 seconds if no
buttons are pressed within 10 seconds.
Auto 30 sec .. The menu will automatically be turned off in 30 seconds if no
buttons are pressed within 30 seconds.
NOTE: If no buttons on the remote control are pressed within 10 seconds, the
PJ buttons light goes out to indicate that you are in the Computer mode. To
enable the projector menu operation again, press the PJ button again to light
red.
Menu
E 36
Setup
Enables you to set operating options.
Press "OK" to save your changes for all the features of Page1, Page2,
Page3, Page 4, Page5 and Page6.
[Page1]
Orientation:
This reorients your image for your type of projection.
The options are: desktop front projection, ceiling rear projection,
desktop rear projection, and ceiling front projection.
Background:
Use this feature to display a blue/ black screen or logo when no
signal is available. The default background is blue. You can change
the logo screen using the PC Card Files feature. See page E-39.
Mouse Settings:
This option lets you to change your USB mouse settings. The mouse
settings feature is available for USB mouse only. Choose the set-
tings you want:
Mouse Button ............. "Right Hand" or "Left Hand"
Mouse Sensitivity ......."Fast", "Medium" or "Slow"
[Page2] PC Card Viewer Options
Show Folder List:
If this option is checked, when PC Card Viewer input is selected on
the projector, the folder lists will be displayed and allows you to
select the presentation from a PC card.
Auto Play:
If this option is checked, any given slide will start to play automati-
cally.
Auto Play Interval:
You can specify interval time between 5 and 300 seconds.
NOTE: The Auto Play Interval time set on the PC Card Viewer Utility over-
rides the one set here.
Manual Play:
Views a slide manually when PC Card Viewer input is selected.
NOTE: The Auto Play and Manual Play options determine the behavior of
the Play/Stop [ / ] icon on the Viewer toolbar.
NOTE: If you check "Auto Play" and select "PC Card Viewer" on the projector,
the slides will automatically start to play back from any given slide.
Capture Options: (available for JPEG only)
These options are used for the Capture function that you can select
from Tools. You have three options for JPEG compression quality:
High quality, Normal and High Compression.
High Quality . Gives quality of JPEG a priority.
Normal ......... Gives normal JPEG quality.
High Compression Gives compression a priority.
[Page3] Signal Select
RGB1/2:
Allows you to choose "RGB" for an RGB source such as a com-
puter, or "Component" for a component video source such as a
DVD player. Normally select "Auto" and the projector automatically
detects a component signal. However there may be some compo-
nent signals that the projector is unable to detect. If this is the case,
select "Component".
VIDEO and S-VIDEO:
This feature enables you to select composite video standards manu-
ally. Normally select "Auto".
Select the video standard from the pull-down menu.
This must be done for Video and S-Video separately.
E 37
[Page4]
Auto Adjust (RGB Only):
When "Auto Adjust" is set to "On", the projector automatically de-
termines the best resolution for the current RGB input signal to
project an image using NEC's Advanced AccuBlend Intelligent Pixel
Blending Technology.
The image can be automatically adjusted for position and stability;
"Horizontal Position", "Vertical Position", "Clock", "Phase", and
"Resolution."
On ................ Automatically adjusts image "Horizontal Position", "Vertical
Position", "Clock", "Phase" and "Resolution".
Off ................ User can adjust the image display functions ("Horizontal Po-
sition", "Vertical Position", "Clock", "Phase" and "Resolution")
manually.
Auto Start:
Turns the projector on automatically when the power cable is in-
serted into an active power outlet. This eliminates the need to al-
ways use the "Power" button on the remote control or projector cabi-
net.
Power Management:
When this option is on and there is no RGB input for five minutes or
more, the projector will automatically turn itself off.
Power Off Confirmation:
This option determines whether a confirmation dialog for turning off
the projector will appear or not.
NOTE: When the confirmation message is displayed, you must be in the
Projector mode to operate your projector using the remote control. If not,
press the PJ button on the remote control to change your projector to the
Projector mode. The button lights to indicate that you are in the Projector
mode.
Keystone Save:
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are saved
when you turn off the projector.
Fan High Speed Mode:
This option allows you to select two modes for fan speed: high-
speed mode and normal speed mode.
When you wish to cool down the temperature inside the projector
quickly, check this box. This is convenient especially when the pro-
jector is installed on the ceiling.
Auto Mute for Built-in Speaker:
This option allows you to mute the built-in speakers automatically
when you connect an audio cable to the AUDIO OUT terminal.
Clear Lamp Hour Meter:
Resets the lamp clock back to zero. Pressing this button appears a
confirmation dialog box. To reset the lamp usage hour, press "OK".
NOTE: The projector will turn off and go into standby mode after 1600 hours
(up to 2600 hours in Eco mode) of service. If this happens, press the "Help"
button on the remote control for ten seconds to reset the lamp clock back
to zero. Do this only after replacing the lamp.
[Page5]
Remote Sensor:
This option determines which remote sensors on the projector are
enabled in wireless mode.
The options are: front, rear, right, or left. All checked boxes indicate
that they can accept the infrared signal from the supplied remote
control.
S-Video Mode Select:
This feature is used to select the S-Video signal detection mode.
This allows identifying of the S-Video signals with different aspect
ratio (Zoom signal 16:9, Wide Zoom signal 4:3).
S2 ............... Identifies Zoom or Wide Zoom signal.
OFF ............. Does not identify any S-video signal.
RGBOUT Terminal:
This option allows you to determine which RGB source is output
from the RGBOUT terminal when the Video, S-Video or Viewer
source is selected.
Disable ......... Neither RGB 1 nor RGB 2 is output from the RGBOUT termi-
nal.
RGB 1 .......... The signal from RGB 1 is output from the RGBOUT terminal.
RGB 2 .......... The signal from RGB 2 is output from the RGBOUT terminal.
NOTE: The AUDIO OUT mini jack outputs sound for the source that the
projector currently selects independently of setting "RGB OUT Terminal".
E 38
[Page6]
Communication Speed:
This feature sets the baud rate of the PC Control port (Mini DIN 8
Pin).
It supports data rates from 4800 to 38400 bps.
The default is 38400 bps. Select the appropriate baud rate for your
equipment to be connected.
Default Source Select:
You can set the projector to default to any one of its inputs each
time the projector is turned on.
Last .............. Sets the projector to default to the previous or last active
input each time the projector is turned on.
Auto ............. Searches for an active source in order of RGB1 RGB2
Video S-Video PC Card Viewer RGB1 and displays
the first found source.
Select ........... Displays the selected source input every time the projector is
started up. Select an input from the pull-down menu.
Tools
Provides tools for capturing images, displaying files in a PC Card and
drawing.
NOTE: The "Capture" and "PC Card Files" features are required for a PC card.
Capture:
Allows you to capture an image from a source that is currently be-
ing displayed. The image is saved as JPEG in the PC card.
When you select Capture from the menu, you will get a tool bar. You
can capture an image directly using the tool bar when the menu is
not displayed.
The tool bar includes the following buttons:
Drag ............. Drags to move the tool bar. (for USB mouse operation only)
Capture ........ Captures an image and save it as a JPEG file in a PC card.
Freeze .......... Freezes and unfreezes images.
Exit ............... Exits the Capture function.
Unless a PC card is inserted into the PC Card slot of the projector,
the Capture feature is not available.
The "Card Error" display means that the free space of the PC card
is insufficient for saving images. Make more space available on the
card by erasing unwanted images with your PC. The number of
images that can be captured depends on the size of the PC card.
NOTE: Be sure not to turn off the power or remove the PC card while cap-
turing an image. Doing so could cause a loss of the data in the PC card or
damage to the card itself.
NOTE: Captured images with higher resolution than the projector's native
resolution cannot be displayed correctly.
PC Card Files:
Displays a list of all the files stored in the PC card so that you can
select a file you want to display. You can also sort files by file name
or date, or display the file.
Although a list of all the files in the PC card is displayed, you can
view files in idx, text, HTML, JPEG and BMP format only.
Selecting BMP and JPEG files automatically switches to the PC
Card Viewer source.
NOTE: When an image with a resolution of XGA (1024
ן
768) or higher is
projected, the PC Card Files screen may not be correctly displayed.
Selecting "Execute" displays the file you selected.
When you select a JPEG or BMP file and press the Enter button on
the remote or the cabinet, or Execute on the above, you will get a
toolbar. This toolbar is used to return to the PC Card Files screen.
Drag
Return
Close
Drag ............. Drags to move the tool bar. (for USB mouse operation only)
Return .......... Returns to the PC Card Files screen.
Close ............ Close the toolbar.
Drag
Freeze
Exit
Capture
E 39
Changing Background Logo:
The Logo button allows you to select a background logo from graphic
files on a PC card and change to it as the background logo.
NOTE: File size must be 64KB or less. Other file formats than JPEG and
BMP are not available.
1. Use the or button to select a JPEG or BMP file for your back-
ground logo.
2. Use the
and then button to select Logo.
3. Press the Enter on the remote control or the cabinet. You will get the
confirmation dialog box.
4. Select OK and press the Enter button. This completes changing a
logo for the background.
* Once you have changed the background from the NEC logo to another,
you cannot return the logo to background even by using Factory De-
fault. To do so, repeat the above steps. The NEC logo file is included
on the supplied CD-ROM (/logo/nec_b_x.jpg).
ChalkBoard: (available only when using with USB mouse)
Provides the tool bar for producing freehand drawings.
Drag ............. Drags to move the tool bar. (for USB mouse operation only)
Pen .............. Left-click and drag to draw. Left-click [] or right-click the
pen icon to display the pen palette containing four lines of
different thickness from which you can select a line you pre-
fer by left-clicking.
Color ............ Selects a color. Left-click to display the color palette from
which you can select a color you prefer by left-clicking.
Eraser .......... Left-click and drag to erase part of a drawing. Left-click []
or right-click the eraser icon to display the eraser palette con-
taining four eraser of different thickness from which you can
select an eraser you prefer by left-clicking.
Clear ............ Left-click to clear the drawing completely from the ChalkBoard
screen.
View ............. Hides the tool bar by left-clicking. Right-clicking anywhere
on the screen displays the ChalkBoard tool bar again.
Exit ............... Clears the complete drawing and exits the ChalkBoard.
NOTE:
* The ChalkBoard feature is available only when a USB mouse is used. Free-
hand drawings cannot be saved or captured.
* The menu is not available while you display the ChalkBoard screen.
* The Capture function is not available on ChalkBoard screen.
* Switching slides clears a drawing completely.
Help
Contents:
Provides an online help about how to use the menus. An under-
lined link means that you can move to an adjustment item directly.
Selecting the underlined link and pressing ENTER moves to the
corresponding adjustment item.
NOTE: The Help Menu may not be displayed correctly when a UXGA signal
is displayed.
Information:
Displays the status of the current signal, and the lamp and the pro-
jector usage hours.
This dialog box has four pages.
The information included are as follows:
NOTE: The progress indicator shows the percentage of remaining bulb life. The
value informs you of the amount of lamp and projector usage respectively.
[Page 1]
Source Name
Input Terminal
Horizontal Frequency
Vertical Frequency
Sync Polarity
[Page 2]
Signal Type
Video Type
Sync Type
Interlace
Resolution
[Page 3]
Aspect Ratio
Gamma Correction
Noise Reduction
Color Matrix
Matrix Type
[Page 4]
Lamp Remaining Time (%)
Lamp Hour Meter (H)
Projector Usage (H)
Drag
Pen
Eraser View
Exit
ClearColor
E 40
Using the PC Card Viewer function
NOTE: When using the supplied software (CD-ROM)
The software is designed to use with a personal computer only. Do not play the
software on CD player. Doing so could cause damage to speakers.
Features
The Viewer feature allows slides stored on a PC memory card (re-
ferred to as PC card in this manual) to be displayed on the projector.
Even if no computer is available, presentations can be conducted sim-
ply with the projector. This feature is convenient for holding presenta-
tions at meetings and in offices, as well as for playing images taken on
digital cameras.
Easy to use
Presentations can be started immediately simply by inserting a PC
card (not supplied)
Easy slide switching
Remote control operation
Jumping to list of slides or any specific slide
High quality images
High resolution up to 1024ן768 dots(MT850: up to 800ן600 dots)
24-bit full color playback
Viewing of digital camera images
Simple utility software (for computer)
PC Card Viewer Utility operable on Windows 95 / 98 / NT4.0 (SP3 or
later) / 2000
Slides can be created by capturing the currently displayed image
Control screen for displaying lists of slides and editing
PC Card Viewer PPT Converter 1.0 [Add-In Version] converts files
created with Microsoft PowerPoint 95/97/2000 (hereafter referred to
as PowerPoint) into indexes playable with PC Card Viewer
* Microsoft, Windows and PowerPoint are registered trademarks of
Microsoft Corporation.
Inserting and Ejecting a PC Card
A PC card is used to view presentation data prepared on the computer
and to capture and play images projected with the projector.
Inserting the PC Card
Hold the PC card horizontally and insert it slowly into the card slot
with its top facing up.
The eject button pops out once the PC card is fully inserted.
Check that the PC card is fully inserted.
NOTE: Do not try to force the PC card into the slot.
PC Card
Ejecting the PC Card
Press the eject button. The PC card pops out a little. Grasp the edges
of the PC card and pull it out. Do not eject the PC card while its data is
being accessed.
Eject button
Direction for Inserting the PC Card
The PC card has a top and bottom and must be inserted into the
PC card slot in a specific direction. It cannot be inserted backwards
or upside-down. Attempting to force it into the slot in the wrong
direction may break the internal pin and damage the card slot.
Refer to the PC card's operating instructions for the proper direc-
tion of insertion.
PC Card Type
The PC Card slot accepts PCMCIA Type II only.
E 41
Installing the PC Card Viewer Software
Before Installing
Perform the following before installing the PC Card Viewer software:
If Windows is already started, exit all applications. Installation may
not be performed properly if any applications are running.
Installation
Install the viewer software as described below.
To quit installation before it is completed, press the "Cancel" button
then follow the instructions in the dialog box.
1. Start up Windows.
2. Insert the CD-ROM into the CD-ROM drive.
The auto CD play function automatically starts the CD-ROM's
program and the contents screen appears.
* The auto CD play function operates if the "Auto insert notification" box in
the computer's CD-ROM control panel is checked. (The box is checked
by default.)
3. Click [Installing the PC Card Viewer Utility 1.0]
The setup dialog appears.
* Follow the instructions in the setup dialog to complete the installation.
For instructions on uninstalling the PC Card Viewer software, see page
E-45.
Starting Up the PC Card Viewer Software
on your PC
(PC Card Viewer Utility 1.0)
Use the PC Card Viewer Utility 1.0 for creating viewer slides.
To start the PC Card Viewer software:
* Select [Start]-[Programs]-[NEC Projector Tools]-[PC Card Viewer
Utility 1.0].
Refer to online help for instructions on using the PC Card Viewer soft-
ware.
Contents of the English version PC Card Viewer software
(PC Card Viewer Utility 1.0)
This is the software used for creating PC Card Viewer slides. In this
manual it is referred to as the "PC Card Viewer software".
PC Card Viewer PPT Converter 1.0
This is an application that converts files created with Microsoft
PowerPoint 95/97/2000 into indexes so that they can be played directly
with the PC Card Viewer Utility 1.0.
PC Card Viewer PPT Converter is installed automatically when you
install the PC Card Viewer Utility.
To start PC Card Viewer PPT Converter:
* Select PC Card Viewer PPT Converter from NEC Projector Tools.
Basic Operation of the PC Card Viewer Software
PC Card Viewer Utility is an application for editing documents, con-
verting them into slides and storing them on PC cards as playback
data (indexes) for presentations using projectors.
E 42
Operating the PC Card Viewer Function
from the Projector (playback)
This section describes the operation for showing slides of presentation
documents created using the PC Card Viewer function with the projec-
tor.
It is also possible to make slides directly from the images projected
with the projector.
Projecting slides
1. Insert a PC card into the card slot.
Insert the PC card with the side with the insertion direction arrow
on the top.
* Press the eject button to eject the card.
2. Select the PC Card Viewer from the Source Select menu.
3. Project slides.
Checking “Show Folder List”, means that selecting PC Card Viewer
input displays a list of the folders in the PC card and if “Auto Play” is
checked the projector automatically starts to play slides at the first
slide of the folder you have selected.
A tool bar will appear when you press the MENU button on the remote
control or the projector cabinet or clicking with the right button of a
mouse.
Drag
Prev Play Jump Setup View
Next Stop Select Delete
The tool bar includes the following buttons:
Drag .......... Drags to move the tool bar (for USB mouse operation only).
Prev .......... Returns to the previous slide or folder. Or this lets you play
slides back in reverse.
Next .......... Advances to the next slide or folder. Or this lets you play
slides back.
Play ........... Plays back automatically or manually depending on the set-
ting on PC Card Viewer Options of the menu. This allows you
to move on to the next slide when Manual Play is selected.
Stop .......... This allows you to stop Auto Play while you are playing back
and to resume playing from the selected slide or folder when
Auto Play is selected.
Jump ......... Displays a list of slides while you are playing back.
Select ........ Displays a list of folders while you are playing back.
Setup ........ Displays the PC Card Viewer Options dialog box on Page 2 of
the Setup dialog box.
Delete ........ Deletes a captured slide(s) or all the captured slides in the
Capture specific folder.
View .......... Hides the tool bar while you are playing back. Pressing the
MENU button or clicking with the right button of a mouse
shows it again.
NOTE: If no PC card is inserted in the PC CARD slot, there is no signal, and a
black, blue or logo background is displayed, depending on the setting.
Playback is stopped when SLIDE +/ on the remote control or
/
button on the cabinet is pressed in Auto Play mode.
NOTE: Up to 12 indexes can be displayed on the list of folders. The folder in the
right bottom is always a folder exclusively for captured images, but is only
displayed when images have been captured. To display the list of folders when
there are 13 or more indexes stored on the PC card, select "Edit index" from the
PC Card Viewer software's "File" menu and move the index you want to display
to within 12 indexes from the top of the folder index. For details on indexes,
refer to the PC Card Viewer software's help folder.
E 43
When the tool bar is not displayed:
Press the FOLDER LIST button on the remote control to display fold-
ers from a PC card in the projectors PC Card slot.
Use the SLIDE +/- button to
advance to the next folder or
return to the previous folder.
Folder
02 : 0001 / 0008
Folder Folder Folder
Folder
Slide Slide Slide Slide
Slide Slide Slide Slide
02 : 0004 / 0008
Slide
Slide(Table) cursor (green marks)
Use the SLIDE +/- button to
advance to the next slide or re-
turn to the previous slide.
Auto Play Mode
If the Auto Play option is selected in PC Card Viewer Options of
the menu, any given slide will start to play automatically. You can
also specify Auto Play Interval between 5 and 300 seconds.
Switching to Slides Directly from Other Input
Modes
With this function it is possible to switch directly to a slide when the
picture of a VCR or computer is being projected.
Example:
When conducting presentations using a combination of slides and
moving pictures from a VCR, etc., it is possible to switch from a PC
Card Viewer slide to the video picture then back to the PC Card Viewer
slide simply by using a source button and PC CARD button.
NOTE: Even if you switch the current PC Card Viewer source to another source,
the current slide is retained. When you return back to the PC Card Viewer, you
will get the slide that has been retained.
NOTE: The PC card editing operation cannot be performed from the projector.
Do so using the PC Card Viewer software.
Folder
Lit red
Works as the Select button
on the projector.
RGB 1
MENU LASER
RGB 2 P
J
Multi cursor (blue marks)
SLIDE
NOTE: You can also use the
and
button on the remote control to select
folders or slides.
If you use the
and
button on the remote control for PC Card Viewer opera-
tion, press the PJ button to switch to the Projector mode and the PJ button
lights red.
KEYSTONE
FREEZE
PIC
-
MUTE
HELP
POINTER
PC CARD
VIDEO S
-
VIDEO
AUTO ADJ.
RGB 1
MENU LASER
R-CLICK /CANCEL
RGB 2 P
J
ONOFF
MAGNIFY
VOL.
SLIDE
FOLDER
SLIDE
LIST
Current folder number
Current slide number
Number of all slides
in folder
E 44
Capturing Images Displayed on the Projector
Storing images displayed on the projector on the PC card
Preparations:
Insert the PC card into the card slot.
Insert the PC card with the side with the insertion direction arrow on
the top.
* Press the eject button to eject the card.
1. Project the image you wish to store on the projector.
2. Select the Capture from the Tools menu.
3. A tool bar will appear.
The tool bar includes the following buttons:
Drag ............. Drags to move the tool bar (for USB mouse operation only).
Capture ........ Captures an image and save it as a JPEG file in a PC card.
Freeze .......... Freezes and unfreezes images.
Exit ............... Exits the Capture function. Another option to exit the Capture
function is to press MENU or CANCEL button on the remote
control or projector cabinet.
NOTE: You can compress a captured file (JPEG) using the Capture Options in
the Setup dialog. See page E-36.
NOTE: Captured images with higher resolution than the projector's native reso-
lution cannot be displayed correctly.
NOTE:
File size of the captured image varies depending on the resolution of an
input signal.
Since an image data is compressed with the JPEG format, the image is slightly
degraded.
NOTE: An hourglass indicating that an image is being captured appears on the
projector's display. Do not eject the PC card or turn off the projector's power
while this icon is displayed. Doing so will damage the PC card data. If the PC
card data is damaged, use a computer to repair the data.
NOTE: The folder in the right bottom is always a folder exclusively for captured
images. To display the list of folders when there are 13 or more indexes stored
on the PC card, select "Edit index" from the PC Card Viewer software's "File"
menu and move the index you want to display to within 12 indexes from the top
of the folder index. For details on indexes, refer to the PC Card Viewer software's
help file.
Drag
Freeze
Capture
Exit
Drag
Prev Play Jump Setup View
Next Stop Select Delete
Deleting Captured Images
Using the Delete button on the tool bar for PC Card Viewer can delete
captured images.
To delete captured images:
1. Select PC Card Viewer.
2. Use
button to select the Capture folder in the right bottom of
the screen.
3. Press the MENU button to display the tool bar.
4. Use the
or
button to select the Delete icon and press the
ENTER button or click with a mouse button.
Viewing Digital Images
Digital images can be played with the PC Card Viewer if the following
conditions are met:
If the image can be stored on an MS-DOS format PC card
If the image can be stored in a format supported by the PC Card
Viewer.
With the PC Card Viewer, images on the card are searched for in
directories and images in JPEG or BMP format are recognized as
slides.
Searchable directories are directories within two steps from the root
directory, and searchable images are images within the first 12 files
in the directory. Only file and slide switching are possible.
NOTE: The maximum number of images recognized as slides within one direc-
tory is 128.
E 45
Uninstalling the PC Card Viewer Software
Even if you do now know the PC Card Viewer software's file names or
where they are stored, the PC Card Viewer software files can be easily
removed from the system using the "Install/Uninstall Applications" con-
trol panel in Windows. (Normally there is no need to perform this op-
eration.)
Uninstalling the software
Use the procedure described below to uninstall the PC Card Viewer
software files.
1. From the "Start" menu, select "Settings" then "Control Panels".
2. In the "Control Panels" dialog box, double-click on "Add/Remove
Programs".
3. In the "Add/Remove Programs Properties" dialog box, click the
"Setup/Remove" tab, then select "PC Card Viewer Utility 1.0" from
the list of applications and click on "Add/Remove".
4. In the "Confirm File Deletion" dialog box, click "Yes".
5. Once the application is uninstalled, click on "OK" in the "Remove
Program From Your Computer" dialog box.
E 46
Terminology
PC card
ATA card
CompactFlash
TYPE (I, II and III)
BMP
JPEG
This is the name of a card currently being standardized by the Japan Electronic Industry Association (JEIDA) and PCMCIA
(Personal Computer Memory Card Interface Association) of the United States.
A type of PC card. ATA was originally a type of interface between computers and fixed disk devices. The ATA card is a standard
card-type recording medium.
CompactFlash card is a small removable card conforming to ATA specifications. It is one-fourth the volume of a PCMCIA card.
PCMCIA 2.1 PC cards are divided into three types according to their thickness: Type I (3.3 mm), Type II (5.0 mm) and Type III
(10.5 mm).
A type of image format. The standard Windows Bit Map format used for MS-DOS/Windows-compatible computers.
A type of image format. "JPEG" is the abbreviation of Joint Photographic Experts Group. JPEG compression offers efficient
data storage. The data not required for displaying the image is identified and deleted. Since the data is deleted, JPEG
algorithms are said to be irreversible. This means that once the image is compressed, the decompressed image it is not the
same as the original image.
E 47
This section describes the simple maintenance procedures you should
follow to replace the lamp and clean the filter.
Replacing the Lamp
After your lamp has been operating for 1500 hours (2500 hours : Eco
mode) or longer, the Status light in the cabinet will go on and the
message will appear. Even though the lamp may still be working, re-
place it at 1500 (2500 hours : Eco mode) hours to maintain optimal
projector performance.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been used. It will
be extremely hot. Turn the projector off, wait a full minute, and then
disconnect the power cable. Allow at least one hour for the lamp to
cool before handling.
DO NOT REMOVE ANY SCREWS except the lamp cover screw and two
lamp housing screws. You could receive an electric shock.
The projector will turn off and go into stand by mode after 1600 (2600
hours : Eco mode) hours of service. If this happens, be sure to replace
the lamp. If you continue to use the lamp after 1500 hours (2500 hours
: Eco mode) of use, the lamp bulb may shatter, and pieces of glass may
be scattered in the lamp housing. Do not touch them as the pieces of
glass may cause injury. If this happens, contact your NEC dealer for
lamp replacement.
To replace the lamp:
1. Loosen the lamp cover screw until the screwdriver goes into a
freewheeling condition and remove the lamp cover. The lamp cover
screw is not removable.
4. MAINTENANCE
E
N
T
E
R
C
A
N
C
E
L
S
E
LE
C
T
P
O
W
ER
STA
TU
S
S
O
N
/
S
TA
N
D
BY
M
E
N
U
S
O
U
R
C
E
A
U
T
O
2. Loosen the two screws securing the lamp housing until the screw-
driver goes into a freewheeling condition. The two screws are not
removable.
Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of electrical
shock. Do not attempt to circumvent this interlock.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
SOURCE
AUTO ADJUST
ON
/
STAND BY
M
E
N
U
E
N
T
E
R
S
E
L
E
C
T
P
O
W
S
T
A
T
U
S
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
3. Insert a new lamp housing until the lamp housing is plugged into
the socket.
CAUTION: Do not use a lamp other than the NEC replacement lamp
(MT50LP). Order this from your NEC dealer.
Secure it in place with the two screws.
Be sure to tighten the screws.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SE
L
EC
T
P
O
W
E
R
STA
T
US
O
N
/
O
F
F
SO
UR
CE
A
U
TO
A
DJU
S
T
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
L
E
C
T
P
O
W
E
R
S
T
A
T
U
S
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
4. Reattach the lamp cover.
Tighten the lamp cover screw.
Be sure to tighten the screw.
E
N
T
E
R
C
A
N
C
S
E
P
O
W
E
R
S
T
A
T
U
S
O
N
/
S
T
A
N
D
B
Y
5. After you install a new lamp, select [Menu] [Projector Op-
tions] [Setup][Page 4][Clear Lamp Hour Meter] to reset
the lamp usage hours.
NOTE: When the lamp exceeds 1600 hours (2600 hours : Eco mode) of ser-
vice, the projector cannot turn on and the message is not displayed. If this
happens, press the OFF or Help button on the remote control for a minimum of
10 seconds while in standby mode. When the lamp time clock is reset to zero,
the STATUS indicator goes out.
E 48
Cleaning or Replacing the Filters
The air-filter sponge keeps the inside of the MultiSync MT1055/MT1050/
MT850 Projector free from dust or dirt and should be cleaned after
every 100 hours of operation (more often in dusty conditions). If the
filter is dirty or clogged, your projector may overheat.
CAUTION
Turn off the power and unplug the projector before replacing the filter.
Only clean the outside of the filter cover with a vacuum cleaner.
Do not attempt to operate the projector without a filter cover.
Your projector will not operate unless the filter cover is installed cor-
rectly.
To clean the air-filter:
Vacuum the filter-through the filter cover.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
S
E
L
E
C
T
P
O
W
E
R
S
T
A
T
U
S
O
N
/
O
F
F
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
U
S
B
A
C
I
N
To replace the air-filter:
1. Remove the filter cover by pushing up on the catch of the cover
until you feel it detach.
M
E
N
U
E
L
L
E
C
T
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
U
S
B
AC IN
1
2
2. Reinstall the new filter cover.
NOTE: Do not detach the sponge from the filter cover. Do not wash the filter
cover with soap and water. Soap and water will damage the the filter mem-
brane. Before replacing the filter cover, remove dust and dirt from the pro-
jector cabinet. Keep out dust and during filter replacement.
A
C
I
N
1
2
E 49
5. TROUBLESHOOTING
This section helps you resolve problems you may encounter while setting up or using the projector.
Standby
Cooling down
Lamp in High-Bright mode
Lamp in Eco mode
3 minutes after lamp is turned on in
Eco mode
Lamp has reached its end of life
(1500 hours or over)
Lamp life has reached its end of life
(1600 hours or over)
Lamp or filter cover error (3 locations)
Temperature error
Fan error
Lamp error
Power/ Status Light Messages
Common Problems & Solutions
Condition
Does not turn on
No picture
Image isnt square to the
screen
Picture is blurred
Image is scrolling vertically,
horizontally or both
Remote control does not
work
Status indicator is lit or blink-
ing
Cross color in RGB mode
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on.
Ensure that the lamp cover is installed correctly. See page E-47.
Check to see if the projector has overheated or the lamp usage exceeds 1600 hours (2600 hours in Eco
mode). If there is insufficient ventilation around the projector or if the room where youre presenting is particu-
larly warm, move the projector to a cooler location.
Use the menu to select your source (Video, S-Video, RGB1, RGB2 or PC Card Viewer). See page E-32.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. See page E-32.
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the Factory Default on the Image Options
Menu in Advanced menu. See page E-35.
Reposition the projector to improve its angle to the screen. See page E-14.
Use the Keystone to correct the trapezoid distortion. See page E-28 or 33.
Adjust the focus. See page E-25.
Reposition the projector to improve its angle to the screen. See page E-14.
Ensure that the distance between the projector and screen is within the adjustment range of the lens. See
page E-17.
Use menus or a source button on the remote control or the cabinet to select the source you want to input.
Install new batteries. See page E-12.
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. See page E-12.
Make sure that you are in the Projector mode or the PJ button lights in red. If not, press the PJ button.
See the Power/ Status Light messages above.
If Auto Adjust is off, turn it on. If Auto Adjust is on, turn it off and balance the image with the Position and Clock
Adjust on the Advanced Options Menu. See page E-34.
Problem Check These Items
Steady orange
Blinking green
Steady green
Steady green
Steady green
Steady green
Steady orange
Steady orange
Steady orange
Steady orange
Steady orange
Steady green
Blinking green
Steady red (High-Bright mode)/
Steady orange (Eco mode)
Steady red
Blinking red (1 sec interval)
Blinking red (4 sec interval)
Blinking red (8 sec interval)
Blinking red (12 sec interval)
Blinks green for 60 seconds
Fixed at High-Bright mode. Lamp mode
can be changed on the menu
Message appears on screen during 1500-
1600 hours of lamp usage. The projector
reaches its end of life. Please replace the
lamp as soon as possible.
The projector is in standby mode and can-
not be turned on.
The projector is in standby mode and can-
not be turned on.
The projector is in standby mode and can-
not be turned on.
The projector is in standby mode and can-
not be turned on.
The projector is in standby mode and can-
not be turned on.
Power Indicator Status Indicator
Note
E 50
Is PC Card Viewer selected from the Source menu?
Is the PC card seated in the PC CARD slot completely?
Are slide data stored in the PC card?
Have the contents of the PC card been destroyed?
While an image with over 1024ן768 dots (MT850: 800ן600 dots) is projected, several lines of information
will be lost. Use the supplied software change the image to 1024ן768 dots in size.
Use a computer, etc., to repair the data.
Condition Status
When using the PC Card Viewer function
For more information contact your dealer.
No picture
Part of a slide is not displayed
Contents of PC Card are
damaged
E 51
6. SPECIFICATIONS
This section provides technical information about the MultiSync MT1055/MT1050/MT850 Projectors performance.
Model Number MT1055/MT1050/MT850
Optical
LCD Panel 1.3 p-Si TFT active-matrix, 800ן600 dots (MT850) / 1024ן768 dots (MT1055/MT1050)
1.3 p-Si TFT active-matrix with Micro Lens Array (MT1055)
Lens Manual zoom, manual focus
MT1050/MT850 : F2.3 2.7 f=48.6 58.4 mm
MT1055 : F1.8 2.2 f=49.3 59.3 mm
Lamp 200W NSH lamp (160W in Eco mode)
The lamp, under normal operating conditions, is warranted for 1500 hours of operation time within 6 months.
Image Size 30 300 inches (762 7620 mm) diagonal
Projection Distance MT1050/MT850 : 4.3 36.7 ft (1.3 - 11.2 m)
MT1055 : 4.3 37.1 ft (1.3 - 11.3 m)
Electrical
Inputs Video (NTSC / PAL / PAL60 / SECAM / NTSC4.43)
Horizontal Frequency : 15 100 kHz (RGB : 24 kHz or over)
Vertical Frequency : 50 120 Hz
Video Bandwidth RGB: 80 MHz
Color Reproduction Full color, 16.7 million colors simultaneously.
Horizontal Resolution 550 TV lines : NTSC / PAL / NTSC4.43 / YCbCr
350 TV lines : SECAM
RGB MT850 : 800 dots horizontal, 600 dots vertical
MT1055/MT1050 : 1024 dots horizontal, 768 dots vertical
Power Requirement 100 120 / 200 240 VAC, 50 / 60 Hz
Input Current 3.5 A (100 120 VAC) / 1.7A (200 240 VAC)
Mechanical
Dimensions
MT1050/MT850 : 11.1" (W)ן4.8" (H)ן14.3" (D) / 281mm (W)ן121mm (H)ן364mm (D) (not including lens and feet)
MT1055 : 11.1" (W)ן4.8" (H)ן14.9" (D) / 281mm (W)ן121mm (H)ן376mm (D) (not including lens and feet)
Net Weight MT1050/MT850 : 13.0 lbs / 5.9 kg
MT1055 : 13.3 lbs / 6.0 kg
Environmental Considerations
Operational Temperatures: 32˚ 104˚F (0˚ to 40˚C), 20 80% humidity
Storage Temperatures: 14˚ 122˚F (-10˚ to 50˚C), 20 80% humidity
Regulations UL Approved (UL 1950, CSA 950)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS3548 Class B
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950, TUV GS Approved)
LCD panels are inherently susceptible to bad pixels.
The LCD panel may have pixel failures at the rate of 0.01% or less.
We provide information about our projectors through the World Wide Web at http://www.nec-pj.com/
The specifications are subject to change without notice.
E 52
Cabinet Dimensions
Unit = mm (inch)
MT1055
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
STAND BY
SOURCE AUTO ADJUST
AC IN
USB
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO RGB INPUT 1
L
/
MONO
R
PC-CARD
AUDIO
RGB MONITOR
OUTPUT
1.5(0.06")
281(11.06")
73.5
(2.89")
121 (4.76")
4
(0.16")
7.5 (0.3")
39.5
(1.56")
376 (14.9")
PC CONTROL
MOUSE
OUTPUT
REMOTE
CONTROL
INPUT
Lens center
Lens center
E 53
Unit = mm (inch)
MT1050/MT850
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
SOURCE AUTO ADJUST
AC IN
USB
S-VIDEO
VIDEO
AUDIO RGB INPUT 2
AUDIO RGB INPUT 1
L
/
MONO
R
AUDIO
RGB MONITOR
OUTPUT
1.5 (0.06")
281 (11.06")
73.5 (2.89")
121 (4.76")
4
(0.16")
6.6
(0.26")
364 (14.33")
39.5
(1.56")
ON
/
STAND BY
PC CONTROL
MOUSE
OUTPUT
REMOTE
CONTROL
INPUT
Lens center
Lens center
E 54
D-Sub Pin Assignments
Mini D-Sub 15 Pin Connector
Pin No. RGB Signal (Analog) YCbCr Signal
1 Red Cr
2 Green or Sync on Green Y
3Blue Cb
4 Ground
5 Ground
6 Red Ground Cr Ground
7 Green Ground Y Ground
8 Blue Ground Cb Ground
9 No Connection
10 Sync Signal Ground
11 Ground
12 Bi-directional DATA (SDA)*
13 Horizontal Sync or Composite Sync
14 Vertical Sync
15 Data Clock*
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
* RGB Input 1 only
51423
10
1112131415
6978
E 55
Timing Chart
Y / N Signal Resolution Frequency H. Refresh Rate Dot Clock
( Dots ) ( kHz ) ( Hz ) ( MHz )
Y NTSC 640 ן 480 15.734 60 -
Y PAL 768 ן 576 15.625 50 -
Y SECAM 768 ן 576 15.625 50 -
Y VESA 640 ן 480 31.47 59.94 25.175
Y IBM 640 ן 480 31.47 60 25.175
Y MAC 640 ן 480 31.47 60 25.175
Y MAC 640 ן 480 34.97 66.67 31.334
Y MAC 640 ן 480 35 66.67 30.24
Y VESA 640 ן 480 37.86 72.81 31.5
Y VESA 640 ן 480 37.5 75 31.5
Y IBM 640 ן 480 39.375 75 31.49
Y VESA 640 ן 480 43.269 85.01 36
Y IBM 720 ן 350 31.469 70.09 28.322
Y VESA 720 ן 400 37.927 85.04 40
Y IBM 720 ן 350 39.44 87.85 35.5
Y IBM 720 ן 400 39.44 87.85 35.5
Y VESA 800 ן 600 35.16 56.25 36
Y VESA 800 ן 600 37.879 60.32 40
Y VESA 800 ן 600 48.077 72.19 50
Y VESA 800 ן 600 46.88 75 49.5
Y VESA 800 ן 600 53.674 85.06 56.25
#Y MAC 832 ן 624 49.725 74.55 57.283
#Y VESA 1024 ן 768 35.5 43 Interlaced 44.9
#Y VESA 1024 ן 768 48.363 60 65
#Y VESA 1024 ן 768 57.476 70.07 75
#Y IBM 1024 ן 768 58.131 72.03 79
#Y MAC 1024 ן 768 60.241 74.93 80
#Y VESA 1024 ן 768 60.023 75.03 78.75
#Y VESA 1024 ן 768 68.677 85 94.5
##Y VESA 1152 ן 864 67.5 75 108
##Y MAC 1152 ן 870 68.681 75.6 100
##Y SUN 1152 ן 900 61.796 65.95 92.94
##Y SGI 1152 ן 900 71.736 76.05 105.6
##Y VESA 1280 ן 960 60 60 108
##Y SGI 1280 ן 1024 63.9 60 107.35
##Y VESA 1280 ן 1024 64.286 60.02 108
##Y MAC 1280 ן 1024 64.31 60.38 107
##Y MAC 1280 ן 1024 65.2 69.89 118.5
##Y HP 1280 ן 1024 78.125 72.01 135
##Y SUN 1280 ן 1024 81.13 76.11 135
##Y VESA 1280 ן 1024 79.976 75.03 135
##Y VESA 1280 ן 1024 91.146 85.02 157.5
##Y
HDTV (1080i)(1125i)
1920 ן 1080 33.75 60 Interlace 74.25
##Y
HDTV (720p)(750p)
1280 ן 720 45 60 Progressive 74.25
##Y
SDTV (480p)(525p)
31.47 59.94 Progressive 27
##Y
SDTV (480i)(525i)
15.73 59.9 Interlace
##Y VESA 1600 ן 1200 75.0 60 162
##Y VESA 1600 ן 1200 81.3 65 175.5
##Y VESA 1600 ן 1200 87.5 70 189
##Y VESA 1600 ן 1200 93.75 75 202.5
#Y: Images in above flagged with # and Y are compressed with Advanced AccuBlend on MT850 only.
##Y: Images in above flagged with ## and Y are compressed with Advanced AccuBlend on MT1055/MT1050 and MT850.
NOTE1: Some composite sync signals may not be displayed correctly.
NOTE2: Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh rate or resolution on your PC.
Refer to Display Properties help section of your PC for procedures.
NOTE3: UXGA can be supported for separate sync signal only.
E 56
12
54 3
6
7
8
PC Control Codes
Function Code Data
POWER ON 02H 00H 00H 00H 00H 02H
POWER OFF 02H 01H 00H 00H 00H 03H
INPUT SELECT RGB 1 02H 03H 00H 00H 02H 01H 01H 09H
INPUT SELECT RGB 2 02H 03H 00H 00H 02H 01H 02H 0AH
INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH
INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H
INPUT SELECT PC CARD VIEWER
02H 03H 00H 00H 02H 01H 1FH 27H
PICTURE MUTE ON 02H 10H 00H 00H 00H 12H
PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H
SOUND MUTE ON 02H 12H 00H 00H 00H 14H
SOUND MUTE OFF 02H 13H 00H 00H 00H 15H
ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H
ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.
Cable Connection
Communication Protocol
Baud rate: 38400 bps
Data length: 8 bits
Parity: No parity
Stop bit: One bit
X on/off: None
Communications Full duplex
procedure:
PC Control Connector (DIN-8P)
To RxD of PC
To TxD of PC
To GND of PC
NOTE: Pins 2, 3, 5, 6 and 8 are used inside the projector.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nec MT850 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nec MT850 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Nec MT850

Nec MT850 Gebruiksaanwijzing - Deutsch - 56 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info