493574
52
Verklein
Vergroot
Pagina terug
1/59
Pagina verder
E–52
4. MAINTENANCE
This section describes the simple maintenance procedures you should
follow to replace the lamp.
Replacing the Lamp
After your lamp has been operating for 1000 hours or longer, the
“Status” light in the cabinet will go on and the message will appear.
Even though the lamp may still be working, replace it at 1000 hours
to maintain optimal projector performance.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Turn the projector off, wait 90
seconds, and then disconnect the power cable. Allow at least
one hour for the lamp to cool before handling.
DO NOT REMOVE ANY SCREWS except the lamp cover
screw and three lamp case screws. You could receive an elec-
tric shock.
The projector will turn off and go into stand by mode after 1100
hours of service. If this happens, be sure to replace the lamp. If
you continue to use the lamp after 1000 hours of use, the lamp
bulb may shatter, and pieces of glass may be scattered in the lamp
case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
To replace the lamp:
1 Loosen the lamp cover screw until the screwdriver goes into a
freewheeling condition and remove the lamp cover. The lamp cover
screw is not removable.
2 Loosen the three screws securing the lamp housing until the screw-
driver goes into a freewheeling condition. The three screws are
not removable.
4 Insert a new lamp housing until the lamp housing is plugged into
the socket.
A
C
IN
PC CARD
USB
AUDIO
VIDEO
S-VIDEO
RGB
PC CONTROL
A
C
IN
PC CA
RD
USB
AUD
IO
VID
EO
S
-VID
EO
RG
B
PC
CON
TROL
A
U
D
I
O
R
G
P
C
C
O
N
T
R
O
L
Interlock
3 Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of electrical
shock. Do not attempt to circumvent this interlock.
AUDIO
RGB
PC CO
NTR
O
L
5 Secure it in place with the three screws.
A
U
D
I
O
S
-
V
I
D
E
O
R
G
B
P
C
C
O
N
T
R
O
L
6 Reattach the lamp cover.
A
U
D
IO
S
-V
ID
E
O
R
G
B
P
C
C
O
N
T
R
O
L
7 Tighten the lamp cover screw.
A
U
D
IO
R
G
B
P
C
C
O
N
T
R
O
L
8 After you install a new lamp, select the Main menu [Projector
Options] [Setup] [Page 4] [Clear Lamp Hour Meter] to
reset the lamp usage hours.
If the projector will not be turned on after using 1100 hours of
service, press and hold the [Help] button on the remote control for
ten seconds or longer to reset the lamp time clock to zero.
CAUTION: Do not use a lamp other than the NEC replacement lamp (LT50LP).
Order this from your NEC dealer.
Be sure to tighten the screws.
Be sure to tighten the screw.
52

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nec LT150 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nec LT150 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Nec LT150

Nec LT150 Gebruiksaanwijzing - Deutsch - 59 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info