493541
13
Verklein
Vergroot
Pagina terug
1/115
Pagina verder
1-9
USB
(
MOUSE/HUB
)
USB
(
PC
)
PC CARD
2
1
PC CONTROL
IN
IN
OUT
OUT
SC TRIGGER REMOTE 2
REMOTE 1
LAN
AC IN
12 3
7
4
8
9
10 11
5
6
1. USB Port [MOUSE/HUB] (Type A)
Connect a USB mouse. You can operate the menu or Viewer
with a USB mouse via this port.
• A USB-supported scanner or PC peripheral can be connected
to this port. (USB Hub Function. See page 4-3)
2. USB Port [PC] (Type B)
Connect this port to the USB port (type A) of your PC using a
USB cable. This port also serves as a PC Control port by using
Dynamic Image Utility 2.0 included on the supplied CD-ROM.
3. PC CARD Slot 1/2
Insert a PC card, commercially available flash memory card or
NEC optional wireless LAN card here.
There are two slots: Slot 1 and Slot 2.
4. PC CARD Eject Button 1/2
Press to eject a PC card partially. Each slot has its own eject
button: 1 and 2.
5. PC CONTROL Connectors (D-Sub 9 pin)
For system expansion such as PC-Control using Dynamic Im-
age Utility included on the supplied User Supportware CD-
ROM or RS232C control from an external control system.
IN: connect to the external equipment such as a PC or control
system.
OUT: for daisy-chaining multiple projectors and operating them
with the same external equipment. To do so, connect to a sec-
ond projector’ s IN terminal to relay the input at the IN terminal
of the first projector until all the projectors are connected.
6. SC. TRIGGER Mini Jack
When the projector is powered ON the screen trigger output
sends a low voltage trigger to the screen controller and the
screen will go down. When the projector is powered OFF the
screen trigger stops sending a low voltage trigger to the screen
controller and the screen will go up.
NOTE: To use this feature, you must turn on the Screen Trigger function. See
page 8-17.
Terminal Panel Features
1. Introduction
Tip (12V)
Ring (0V)
Sleave (ground. 0V)
Stereo mini cable
(not supplied)
NOTE: Screen controllers are supplied and supported by screen manufacturers.
NOTE: Do not use this jack for anything other than intended use. Connecting the
wired remote control to the SC. TRIGGER Mini Jack causes damage to the re-
mote control.
7. LAN Port (RJ-45)
This port is typically used for UTP Ethernet/Fast Ethernet. Use
this connector to control the projector on a LAN. See page
2-12.
8. REMOTE 1 (Mini D-Sub 15 Pin)
This terminal allows external control of the projector by use of
contact closure. See page 10-9.
9. REMOTE 2 Mini Jacks (IN/OUT)
IN: wired remote control input.
OUT: for daisy-chaining multiple projectors and operating them
with the same remote control. To do so, connect to a second
projector’ s IN terminal to relay the input at the IN terminal of
the first projector until all the projectors are connected.
10. Main Power Switch
When you plug the supplied power cable into an active wall
outlet and turn on the Main Power switch, the POWER indica-
tor turns orange and the projector is in standby mode. See
page 3-2.
11. AC IN
Connect the supplied power cable’s three-pin plug here.
Three types of power cable are supplied with this projector:
three-pin type for U. S. A. and Canada. Two-pin type for Europe
and Japan.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nec GT 5000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nec GT 5000 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Nec GT 5000

Nec GT 5000 Gebruiksaanwijzing - Deutsch - 115 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info