512562
14
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
14
TRACKER 5100/5100i/5500/5500i Installation and Operation Manual
NAVMAN
3-2 Distance and bearing calculator
The distance and bearing calculator can plot a course
of one or several legs and to show the bearing and length
of each leg, as well as the total distance along the course.
The completed course can be converted into a route.
To use the distance and bearing calculator:
1 Press ESC until the chart display is displayed.
Press MENU and select Distance.
2 Move the cursor to the start of the first leg. It
does not matter if this point is a waypoint or
not. Press ENT.
3 To add a leg to the course, move the cursor to
the end of the leg. It does not matter if this
point is a waypoint or not. The display shows
4 To change the data display:
i Select Data setup.
ii Change a data field:
a Press the cursor keys to highlight the
field.
b Press ENT to display a menu of the
data that can be shown in the field.
c Select the data to show in the field;
select None to leave the field empty.
iii Repeat the above step to set the other data
fields. Press ESC.
Tip: If less than four lines are used, the
numeric data will take up less of the chart area.
5 To turn the compass display off or on:
i Select Compass.
ii Select Off or On.
6 Finally, press ESC to return to the chart display.
3-3 Goto
Goto is a simple way of navigating straight to one
point.
To start the Goto
1 Choose the point to go to:
To go to a waypoint or to any point on the
chart:
i Press ESC until the chart display is
displayed.
ii Move the cursor to the destination.
iii Press MENU and select Goto.
To go to a waypoint from the waypoints
display:
i Press DISP and select Waypoints.
ii Press
or to highlight the
destination waypoint.
iii Press MENU and select Goto.
Warning: Make sure the course does not pass
over land or dangerous waters.
2 The TRACKER starts navigating to the
destination (see section 2-7). The chart shows:
The destination point marked with a circle.
The boat’s plotted course to the
destination.
Two CDI lines, parallel to the boat’s plotted
course (see appendix C, CDI).
To cancel a Goto
1 Press ESC until the chart display is displayed.
2 Press MENU and select Cancel goto.
the bearing and length of the leg, as well as
the total distance along the course. Press ENT.
4 To remove the last leg from the course, press
MENU and select Remove.
5 Repeat the above two steps to enter the whole
course.
6 To save the new course as a route, press
MENU and select Save. This also saves any
new points on the course as new waypoints,
with default names. If necessary, edit the route
later (see section 10-2-2) and edit any new
waypoints later (see section 9-2-3).
7 Finally, press ESC to return to the chart display.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Navman Tracker 5500i bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Navman Tracker 5500i in de taal/talen: Engels als bijlage per email.

De handleiding is 0,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Navman Tracker 5500i

Navman Tracker 5500i Gebruiksaanwijzing - Nederlands - 41 pagina's

Navman Tracker 5500i Gebruiksaanwijzing - Deutsch - 43 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info