512563
34
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
34
TRACKER 5100/5100i/5500/5500i Installation and Operation Manual
NAVMAN
Power/data cable for display unit
Wire the cable as shown on the next page.
Note:
The unit requires 12 V DC power. This power
supply must be protected with a fuse or circuit
breaker of between 2 and 3 A. If it does not
have this, fit a 2 A fuse in the power supply line.
To enable auto power (see section 2-1),
connect the yellow Power/data cable wire to
the positive power supply as shown.
To disable auto power, leave the wire
disconnected; make sure it can not touch any
other conductor.
If the external beepers and lights require more
than 200 mA DC total, fit a relay.
For information on how to connect NavBus, refer
to the NavBus Installation and Operation manual.
Setup and test
1 Remove the dust covers from the connectors.
2 Plug the eight way connectors into their
sockets on the back of the display unit:
Match the colour on the end of the
connector to the colour of the nut on the
socket.
Hold the plug against the socket and rotate
the plug until it slides into the socket.
Lock the plug in place by pushing the
locking collar towards the socket and
turning it a quarter turn clockwise.
Nothing will be damaged if a cable is plugged
into the wrong socket by mistake.
3 If the unit has an external GPS antenna:
Plug the gold connector into its socket on
the back of the display unit.
Hand tighten the locking collar clockwise -
do not overtighten.
4 If the display unit is bracket mounted:
i Hold the display unit in place on the
mounting bracket shaft, with the rubber
washer clamped between the bracket and
the display unit.
ii Adjust the tilt and rotation of the display unit
for best viewing and hand tighten the knob.
5 Remove the dust cover. Turn the TRACKER on
(see section 2-1).
6 Insert any required C-MAP™ chart card (see
section 1-2).
7 When the TRACKER is turned on for the first
time, the TRACKER displays an installation
menu of setup data:
i Select the language to use.
ii Change the setup data if necessary:
Select the data item to change.
Use the cursor keys to change the data.
Press ENT.
iii When the setup data is correct, press
ESC.
These installation options can be changed
later, through the setup menu (see section 13).
8 At the satellite display, check that it picks up
GPS satellites. Wait for the GPS receiver to
start up and the fix type to change from
‘Acquiring’ to ‘GPS fix’. This should take less
than two minutes (see section 7).
9 If the TRACKER is to send NMEA data to an
autopilot, set this up (see section 13-8).
10 If the TRACKER is part of a NavBus system,
set the backlight group. Otherwise turn NavBus
off (see section 13-8).
11 Go on a test run to check that the navigation
equipment works correctly, particularly when a
radio transmitter or radar is used.
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Navman Tracker 5100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Navman Tracker 5100 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Navman Tracker 5100

Navman Tracker 5100 Gebruiksaanwijzing - Nederlands - 41 pagina's

Navman Tracker 5100 Gebruiksaanwijzing - Deutsch - 43 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info