512556
22
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
22
Diesel fuel flow sensor kit Installation and Operation Manual
NAVMAN
Installation sequence
The fuel lines are modified and temporary
straight through pipes fitted where the sensors
will be fitted. The engine is run, then the real
sensors are fitted. This procedure ensures
that debris from the installation does not enter
the sensors.
The recommended installation sequence is:
1 Read this manual and the documentation
that comes with the other parts. Read
section 7-1 for background information on
fuel pipes and fittings.
2 Plan the installation and choose where
the fuel flow sensors and cables will
be located (see section 7-3). Choose
suitable fittings for connecting the sensors
to the fuel lines (see section 6-3)
3 Install temporary straight through pipes in
the fuel line where the sensors will later
be fitted (see section 7-4).
4 Bleed the fuel lines and test run the
engine. Then remove the two straight
through pipes and fit the two fuel flow
sensors (see section 7-5).
6 Install the tachometer (see section 7-6).
7 Install the cables to link the parts of the
system together and to the Navman
display instrument (see section 7-7).
8 Setup the Navman instrument to use the
fuel flow sensors and tachometer, as
described in the instrument’s installation
and operation manual. Take the boat on
a test run and check that the sensors are
performing correctly.
If you are unsure where a part should be
installed, mount and wire the part temporarily,
without cutting holes in the boat. After the sea
trials have been completed, install and wire the
part permanently.
7 Installing the diesel flow sensor kit
Correct installation is critical to the
performance of the unit. Before starting
installation, it is vital to read this manual
and the documentation that comes with
the other parts.
Ensure that any holes that you cut will not
weaken the boat’s structure. If in doubt,
consult a qualified boat builder.
One important thing to stress is the need
for cleanliness in the installation process.
Diesel engines, and the Navman sensors
are built to fine tolerances - do not allow
any dust, dirt, water or particles to enter
the fuel system.
DAMAGE WILL RESULT if you ignore
this warning.
Warnings
If the boat has twin engines then a second diesel flow sensor kit can be fitted and connected to
the same Navman instrument. To install the kits, fit a kit to each engine, following the instructions
above for each engine and tank. At the display unit, connect the sensor cables from the two kits
in parallel (see section 7-7-2).
The sensors need to be identified as port and starboard in the display unit. You may find more
instructions included in the display head manual.
7-1 Twin engine installations
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Navman Diesel Fuel Flow Sensors bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Navman Diesel Fuel Flow Sensors in de taal/talen: Engels als bijlage per email.

De handleiding is 0,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Navman Diesel Fuel Flow Sensors

Navman Diesel Fuel Flow Sensors Gebruiksaanwijzing - Nederlands - 32 pagina's

Navman Diesel Fuel Flow Sensors Gebruiksaanwijzing - Deutsch - 34 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info