512555
20
Verklein
Vergroot
Pagina terug
1/77
Pagina verder
20
FUEL 3100 / DIESEL 3200 Installation and Operation Manual
NAVMAN
To check out the installation:
1 Power on the boat and any other
instruments. Check the instruments work
properly.
2 Enter the setup data (see section 3).
Set dUAL, motor , and InPUt first, then
enter the rest of the setup data.
For boats with twin tanks or twin engines,
remember to enter port and starboard data
separately where required.
3 Fill the fuel tank(s) and set the fuel in the
tank(s) in the FUEL 3100 or DIESEL 3200 (see
section 5).
4 On boats with twin engines, check the
installation of the port and starboard fuel
sensors:
DIESEL 3200: Start the port engine. Check
the LED lights under the sensors are
blinking. This indicates the sensors are
operating correctly. Confirm the fuel flow is
being displayed as port engine fuel usage
on the instrument. (If it is being displayed
as starboard engine fuel usage, swap
over the fuel flow sensor connectors on
the ‘T’ connector.) Repeat the check with
starboard engine.
FUEL 3100: Start the port engine. Confirm
the fuel flow is being displayed as port
engine fuel usage on the instrument. If it is
being displayed as starboard engine fuel
usage, reconfigure the settings (see section
3-3).
5 FUEL 3100 only: Calibrate the fuel sensor(s)
(see section 3-4).
6 If a paddlewheel speed sensor is
connected, calibrate it (see sections 3-8
and 3-9).
7 Take the boat for a trial run and check the
unit is displaying the correct data.
FUEL 3100: Recalibrate the FUEL 3100’s fuel
sensor(s) after the first 100 engine hours (see
section 3-4).
When you add or remove fuel from a tank, you
must enter into the FUEL 3100 or DIESEL 3200
how much fuel you have added or removed.
Otherwise REMAINING, RANGE and the low
fuel alarm will be meaningless. Twin tanks
connected by an open balance pipe should be
trated as a single fuel tank.
When you add or remove fuel from a tank:
a When you fill a tank
1 Fill the tank.
2 Press until REMAINING is displayed.
3 If the boat has twin tanks, press ENT until
the display shows the name of the tank you
have filled, PORT or STBD.
4 Press and together.
5 If the boat has twin tanks and you are filling
the other tank as well, repeat the above
steps.
Note:
It is often very difficult to refill underfloor
fuel tanks to the same level twice, due to air
pockets. Because of this, owners of boats with
underfloor fuel tanks should:
Ensure the boat is trimmed to sit at
the same angle in the water each time
procedure a above is followed.
Mostly use procedure b below when filling
the tank, but use procedure a above about
every tenth fill.
b When you fill or part fill a tank
1 Before adding or removing fuel, press ESC
and ENT together, then press until the
FUEL setup menu is displayed.
2 Press ENT, then press or until the
FUEL data is displayed.
5 When you add or remove fuel
4-7 Testing the installation
4-8 Resetting to factory defaults
To reset to factory defaults:
1 Turn the power off.
2 Hold ENT + while turning on the power
and for at least five seconds after.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Navman Diesel 3200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Navman Diesel 3200 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Navman Diesel 3200

Navman Diesel 3200 Gebruiksaanwijzing - Nederlands, Deutsch, Français - 77 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info