663846
107
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
NAVMAN 8120/8084 Installation and Operation Manual 107
3-2 Flow indicates no fuel or low fuel:
a Check that the number of engines is set to
1 (see section 19-6).
b Check that the fuel cable connectors
are securely plugged in and the collar is
locked in place. The collar must be locked
in place to give a watertight connection.
c A fuel transducer may be clogged. If so,
remove the transducer from the fuel line
and gently blow through it in the opposite
direction to the fuel flow.
A fuel filter between the fuel transducer
and the fuel tank must be installed as per
the fuel installation guide. Failure to do so
will void the warranty.
d Inspect the fuel cable from end to end for
damage such as cuts, breaks, trapped or
squashed sections.
e Check that the fuel filter is clean.
3-3 A twin engine installation shows only
one flow rate:
a Check that the number of engines is set to
2 (see section 19-6).
3-4 Erratic Fuel Flow readings:
a The fuel flow transducer may have been
mounted too close to the fuel pump or
may be subject to excessive vibration.
Refer to the installation instructions
supplied with the fuel transducer.
b Check for leaks in the fuel line or in the
fuel pickup in the tank.
c The Flow filter value is not suitable
for the engine. Check that the value is not
set to zero, then try increasing the value
until a steady flow rate is shown (see
section 19-6).
3-5 There is no reading for fuel economy:
a The boat must be travelling through the
water to generate an Economy reading.
b Check that the paddlewheel on the
transducer is spinning freely and that the
two magnets in the paddlewheel are still
in place.
B-4 Sonar fishfinding problems
4-1 The Instrument operates erratically:
a Check that the transducer does not have
debris (e.g. weed, plastic bag) caught
around it.
b The transducer may have been damaged
during launching, running aground or
while underway with debris etc. If the
transducer has been impacted, it may
have been kicked up on the bracket. If
it is not physically damaged, reset the
transducer back to its original position.
(See the Transom Transducer Installation
Guide.)
c When the transducer is less that 2 ft
(0.6 m) from the bottom, the depth
readings may become inconsistent and
erratic.
d Manual Gain may be set too low, which may
cause weak bottom echo or no fish signals.
If in Manual Gain, try increasing the Gain.
e Ensure the back of the bottom surface
of the transducer is slightly lower than
the front and the front is as deep in the
water as possible in order to minimize the
generation of bubbles through cavitation.
(See the Transom Transducers Installation
Guide)
f Check the transducer and power cable
connectors at the back of the display unit
are securely plugged in and the collars
are locked in place. The collars must be
secure for watertight connection.
g Inspect the power cable from end to end
for damage such as cuts, breaks, squashed
or trapped sections.
107

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Navman 8084 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Navman 8084 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info