602906
29
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
The T 748’s internal AM/FM tuner oers very high quality sound from radio
broadcasts. The reception and sound quality will always be dependent to a
degree however on the type of antenna(s) used as well as proximity to the
broadcast origin, geography and weather conditions.
ABOUT ANTENNAS
Connect the supplied lead-type FM antenna to the FM antenna input.
Extend the lead. Experiment freely with your antenna placement and
orientation until you get the clearest sound and lowest background noise.
Fix the antenna in the desired position by using thumb tacks, push pins or
any suitable means.
In areas of poor FM reception, an exterior FM antenna can improve
performance dramatically. If radio listening is important to you, consider
consulting an antenna installation professional to optimize your system.
The supplied AM “loop antenna will usually provide adequate reception.
However, an exterior AM antenna can be used to improve reception.
Consult an antenna professional for more information.
IMPORTANT NOTE
When using the AVR 4 to carry out AM/FM commands, ensure that the
DEVICE SELECTOR is set to “TUN”.
ASSEMBLING THE LOOP ANTENNA
1 Rotate the outer frame of the antenna.
2 Insert the bottom edge of the outer frame into the groove on the stand.
3 Extend the antenna cord.
SELECTING A TUNER BAND
Press the [AM/FM/DB] button on the AVR 4 while at AMP or TUNER device
selector page. Each subsequent press will toggle you through AM, FM or
DAB band. Stop (release button) at your desired tuner band.
TUNING AM/FM STATIONS
Upon selecting AM or FM band, use TUNE [ ] on the AVR 4 to
perform slow manual search; press and hold to automatically search.
The front panel [ a/s ] or AVR 4’s [ A/S ] buttons can also be used to tune
for stations.
1 Press [ A/S ] momentarily to step up or down between AM or FM
frequencies.
2 Press and hold [ A/S ] for more than 2 seconds to search up or down
- the T 748’s tuner will stop at the next suciently strong signal it
encounters.
3 Pressing the [ A/S ] during the search process will stop the search.
DIRECT TUNING
If you know your desired stations frequency allocation, you can tune
directly to the station.
1 Toggle [ENTER] button to switch between “Preset and Tune” mode (see
the lower line of the VFD). Select Tune mode.
2 Using the numeric keys of the remote control, key-in the frequency
allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,
“4”, “5” and “0”.
STORING PRESETS (AM/FM)
The T 748 can store up to 30 FM and 30 AM stations for immediate recall.
1 To store a desired AM/FM station to a preset, rst tune to the desired
frequency (see above), then press AVR 4’s [MEMORY] button. The VFD
will show the next available Preset number – for example, “Preset 4 Free”
in the lower line and on the upper right corner “P-4” with “4” blinking.
2 Press the [MEMORY] button again to store the desired frequency on
the Preset number shown. Your desired frequency is now stored in the
assigned preset.
3 Alternatively, an AM/FM station can be stored to a Preset number by
repeating step 1. Enter a Preset number in two ways
• Directly enter a number between 1 to 30 and then press [MEMORY]
button.
• Toggle [ d/f ] or [ D/F ] to step through the Preset numbers, stop
at desired number and then press [MEMORY].
NOTE
If there is no more vacant Preset number, you can overwrite an existing
Preset number by pressing the [ D/F ] buttons to select the Preset
number you want to overwrite
AUTOMATIC PRESET
Preset stations may also be programmed automatically for the entire FM (or
AM) band.
1 Toggle the [AM/FM/DB] button to select FM (or AM) band.
2 Press and hold the [MEMORY] button until the station frequency
indication begins to increase.
3 Release the button and note that the tuner will search the entire FM
(or AM) band, and stop briey at each station that has acceptable
signal strength. The T 748 will automatically assign a preset number to
each station, and then search for the next station. Up to 30 of the best
received FM stations (or 30 AM stations) will be automatically stored.
DIRECT RECALL OF A PRESET NUMBER
You can directly recall a desired Preset number.
1 Toggle [ENTER] button to switch between “Preset and Tune” mode (see
the lower line of the VFD). Select “Preset” mode.
2 Using the numeric keys of the remote control, directly key-in your
desired Preset number. For example, to enter Preset 5, press “5”.
DELETING A STORED PRESET
You can empty a preset by deleting the stored information.
1 Select the preset number to be deleted.
2 While at the selected preset number, press the [DELETE] button.
3 The preset will then be deleted. “Delete” is briey shown in lower line of
the VFD.
4 To clear all the Presets at the same time, repeat step 2 again but this
time do not release the [DELETE] button. Press and hold [DELETE]
button until the current Preset number shown in the VFD is
extinguished (P--). “Delete All” is briey shown in lower line of the VFD.
All Presets are now deleted.
OPERATION
LISTENING TO AM/FM RADIO
29
ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw NAD T748v2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van NAD T748v2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van NAD T748v2

NAD T748v2 Gebruiksaanwijzing - Nederlands - 40 pagina's

NAD T748v2 Gebruiksaanwijzing - Deutsch - 40 pagina's

NAD T748v2 Gebruiksaanwijzing - Français - 40 pagina's

NAD T748v2 Gebruiksaanwijzing - Italiano - 40 pagina's

NAD T748v2 Gebruiksaanwijzing - Português - 40 pagina's

NAD T748v2 Gebruiksaanwijzing - Espanõl - 40 pagina's

NAD T748v2 Gebruiksaanwijzing - Svenska - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info