745050
7
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
ENGLISH
7
PROTECT MODE
If one or more PROTECT LEDs turn red or become all extinguished, this
indicates that the protection circuitry of the M28 had been engaged.
Immediately press the Standby button, turn o Power switch and then
unplug the mains power cord from the mains power source. Undertake
the following
a Check if all speaker wires are connected correctly and that none of
the wires are damaged, causing a short circuit.
b Another cause may be excessive heat build-up inside the amplier.
Make sure there is adequate ventilation around the amplier and
that none of its ventilation slots, top or bottom are blocked. After
the amplier has cooled down, it will function normally again.
c In case one or more of the PROTECT LEDs or Power indicator remained
illuminated in red despite the checks mentioned above, immediately
press the Standby button, turn o Power switch and then unplug the
mains power cord from the mains power source. Have the unit inspected
by a qualied service technician before attempting to use it again.
4 SELECT
Use this switch to select the type of analog audio input.
SELECT switch settings
Upper position – SINGLE-ENDED input is selected.
Lower position – BALANCED input is selected.
WARNING!
Do not adjust the SELECT switch while the M28 is at operating mode.
Use SELECT switch to choose BALANCED or SINGLE-ENDED only when
the M28 is at standby mode or powered down.
5 +12V TRIGGER IN
The +12V Trigger input allows the M28 to be switched remotely
from standby mode to ON and vice-versa by an ancillary equipment
such as a preamplier, AV processor, etc. The controlling device
must be equipped with a 12V trigger output to use this feature.
WARNING
The front panel o (Standby) button is disabled as long as the male plug
of the mono cable (with or without +12V DC) is connected to M28’s
+12V TRIGGER IN. Unplug the mono cable for the M28 to be normally
switched ON (or back to standby mode) using the front panel o
(Standby) button.
6 LED LEVEL (DIMMER)
Toggle to reduce or restore Power indicator brightness or
completely turn it o.
7 FUSE HOLDER
In the unlikely event a fuse needs to be replaced, unplug the mains
power cord from the wall. Then, remove all connections from the
amplier. Use a athead screw driver or similar to open the fuse
holder via the slot indicated. With the screw driver in place, push
and turn counterclockwise to open the fuse holder.
Only replace the fuse with the same type, size, and specication.
IMPORTANT NOTICE
Do not use any substitute fuses of dierent types or with dierent
ratings or values. Failure to observe this precaution may cause damage
to the amplier circuits and may create a re hazard and/or defeat the
safety built into the amplier and may void the warranty.
8 SPEAKER
The M28 is equipped with gold-plated, color-coded, transparent
and special high-current binding-post speaker terminals.
Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL and
SURR-BR speaker terminals to corresponding speakers. Make sure
the “+” (red) terminal and “-” (black) terminal are connected to the
corresponding “+” and “-” terminals of the speaker. Use extra care
to ensure that no stray wires or strands cross between posts or
terminals at either end.
The M28 is designed to produce optimum sound quality when
connected to speakers with impedances within its operating range.
Please make sure that all the speakers are rated 4 ohms minimum
per speaker.
NOTE
Use stranded wire of at least 16 gauge (AWG). Connections to the M28
can be made with banana plugs or by using bare wire or pins. Use the
transverse hole through the post for bare-wire or pin connections. By
loosening the terminal’s plastic nut, make a clean, neat connection and
re-tighten carefully. To minimize the danger of short-circuit, ensure that
only 1/2-inch of exposed wire or pin is employed when connecting.
9 POWER
Supply the AC mains power to the M28.
When the POWER switch is set to ON position, the M28 goes to
standby mode as shown by the amber status condition of the
Power indicator. Press o (Standby) button to switch ON the M28
from standby mode.
If you intend not to use the M28 for long periods of time (such as
when on vacation), switch o the POWER switch.
The o (Standby) button cannot activate the M28 with the rear
panel POWER switched o.
10 AC MAINS INPUT
The M28 comes supplied with two types of detachable mains
power cord. Select applicable type for your usage. Connect
corresponding end of the mains power cord to the AC mains input
of M28 and the plug connected to a mains power source.
Always disconnect the mains power plug from the mains power
source rst, before disconnecting the cable from the M28’s AC
Mains input socket
IDENTIFICATION OF CONTROLS
REAR PANEL
© NAD M28
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
POWER
ON
SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER
SPEAKER SPEAKER
© NAD M28
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
SELECT
BALANCED
SINGLE-ENDED
PROTECT
ANALOG AUDIO INPUT
POWER
ON
SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER
2 CHANNEL AUDIO OUT
UNBALANCED
R BALANCED
DIGITAL AUDIO OUTPUT
AES/EBU
S-VIDEO OUT
L BALANCED
L
R
POWER
ON
COMPONENT VIDEO OUT
AUDIO OUT
L R
HDMI OUT1
HDMI OUT2
HDMI OUT1
HDMI OUT2
12V IN
12V OUT
DIGITAL AUDIO OUT
OPTICAL
COAXIAL
COMPONENT VIDEO OUT
COMPONENT VIDEO OUT
12V IN
12V OUT
DIGITAL AUDIO OUT
OPTICAL
COAXIAL
POWER
ON
100-240V ~ 50/60Hz
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw NAD M28 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van NAD M28 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info