602911
11
Verklein
Vergroot
Pagina terug
1/146
Pagina verder
11
Installation
RACK-MOUNT INSTALLATION
Instructions for installation of the NAD CI-series amplifier are supplied with the Rack-Mounting hardware.
Supplied with these instructions are 8 pieces of plastic bushings and 4 #10-32 bolts. These bolts with
specifically designed plastic bushings are engineered to prevent ground loops and will support the weight
of the NAD CI-series amplifier (see Figure 1).
Figure 1
Since the NAD CI-series amplifier is a heavy amplifier, we recommend that you mount the NAD CI amplifier
as close to the bottom of a rack as possible to promote a stable Rack-Mount installation.
The NAD CI-series amplifier takes up 3 standard, rack places on an EIA/IEC 19-inch rack. The NAD CI-series
amplifier needs special consideration when rack-mounting to allow sufficient ventilation space all around
the amplifier. Thus we recommend one should allow at least a one-rack-space below and above the
amplifier as clearance, and that you allow more than 2 to 3 inches (5 to 7.5 cm) of space on all six sides
of the NAD CI-series amplifier. Please refer to the “Ventilation Air Flow” specification found at the back
of the instruction manual for maximum airflow requirements.
SHELF-MOUNT INSTALLATION
REMOVAL OF RACK-MOUNT BRACKETS
This unit may be installed on any level surface that is strong enough to support the amplifier’s weight.
Please refer to the “Specifications” section at the back of the instruction manual for the exact weight of
your NAD CI-series amplifier. Since the NAD CI-series amplifier was shipped with Rack-Mounting hardware
attached, below is the removal procedure of the rack-mounting shelf brackets. We strongly recommend
that you follow these procedures in order to prevent damage to the NAD CI amplifier or personal injury:
To detach the rack-mount bracket, place the amplifier on a flat surface, remove each set of three
fixing screws on each side. Once the screws are removed, slide the bracket toward the rear of
the amplifier to release it from its fittings in the chassis bottom surface and then slide the
bracket toward you.
For self-mount installations of the NAD CI-series amplifier, we recommend that you do not place
equipment on top of the amplifier. Leave at least 2 to 3 inches (5 to 7.5 cm) on all sides of the amplifier
so that the NAD CI-series amplifier achieves adequate airflow. We strongly recommend that you do not
block the side, top, back and front, airflow vents. Since its power transformer generates a significant
magnetic hum field, a turntable (especially one with a magnetic pick-up cartridge) or a television should
not be located adjacent to, directly above, or below the amplifier.
ENGLISH
FRANÇAISDEUTSCHNEDERLANDSESPAÑOL
ITALIANO
PORTUGUÊS
SVENSKA
Rack-mount bracket
(Left)
These shoulder washers are for use to rack-mount
this unit.
If properly installed (See diagram), the washers will
insulate the amplifier from the rack, preventing
ground loops and hum, and will protect the unit’s
surface from damage.
#10-32UNF-3A screw
4pcs required per unit
Shoulder washers
8pcs required per unit
Mounting rack rail
EIA standard RS-310-C
89.0mm 3U mounting rail hole
CI9120_9060 manual (GB) 12/12/02 9:09 pm Page 11
Downloaded from www.Manualslib.com manuals search engine
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw NAD CI9060 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van NAD CI9060 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info