BEFORE YOU BEGIN
GB - 1 GB - 2 GB - 5 GB - 6
GB - 7 GB - 8 GB - 9
Be sure to connect the color coded leads according to the diagram. Incorrect
connections may cause the unit to malfunction or damage the vehicle’s electrical
system.
Be sure to connect the speaker (-) leads to the speaker (-) terminal. Never connect
the left and right channel speaker cables each other or to the vehicle body.
Make sure all the connections are completely correct before turning on your unit.
When replacing the fuse(s), the replacement must be of the same amperage as
shown on the fuse holder.
Do not block vents or radiator panels. Blocking them will cause heat to build up
inside and may result in re.
After completing the installation and beginning to play the unit(including replacing
the battery), press RESET button on the base with pointed object (such as ball-
point pen) to set the unit to initial status.
Do not attempt to modify the unit, modifying the unit may cause an accident.
Stop the vehicle before carrying out any operation that could interfere with your
driving.
Do not work in extremely high or low temperature. Be sure the temperature inside
the vehicle is between +60°C and -10°C before turning on your unit.
To avoid the driver distract his attention from, please install the unit in an apt
place.
Using the unit after starting the engine, otherwise the unit can not be started,
because the electric energy of battery was used up.
Do not use the unit in extreme high temperature or such low temperature
conditions, and also avoid humidity and direct sunlight, otherwise the electric
energy of battery will be wasting for the high temperature.
Take care of the magnetism of the unit. Do no put the credit card, cassette or
watch around the unit, otherwise they would be broken or some information in
them loses.
To avoid disturbing the video frequency, keep far away from the unit when using
your phone.
Do not put the remote control under high temperature or where the sun strikes it,
or else the remote control can not work normally.
Please warn children not to play the motorized screen which might hurt their
ngers.
When driving, cannot watch the video and the pictures, a warning would be display
on screen.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
When you select or create a disc to play with this product, please note:
•
Avoid long le names! It is suggested to name the le with no much than 7 characters.
• The total number of les on the disc should not exceed 1633.
• The maximum number of directories should not exceed 195.
• The maximum depth level of directories should not exceed 10.
• File system(SD & USB): FAT 32 and FAT 16.
WIRING CONNECTION
Note: Connect one clip end of the provide Ground line (black) to the xing screw bolt,
and connect the other end to the negative pole of the power source. Otherwise the
video on screen may ash.
UNPACK YOUR UNIT
R25. SEARCH button: To search for a desired title, chapter or Track.
R26. APS/ button : To auto preset radio stations.
R27. ZOOM button: To access the zoom function
R28. INT (Intro)button: To start/ cancel intro playback.
R29. RPT (Repeat)button : To repeat playback .
R30. RDM (Random)button : To start/ cancel random playback.
R31. A-B (Repeat A-B) button: To repeat section A to B
R32. AUDIO button: To change the audio setting (DVD only).
REPLACING BATTERY FOR THE REMOTE CONTROL
1.Push the button toward right.
2.Pull the battery loader out.
3.Insert one “CR2025” size battery with the positive side (+) facing up.
4.Replace the cover.
Notes on batteries
• Never recharge the batteries, apply heat to them or take them apart.
• Battery shall not be exposed to excessive heat such as sunshine, re or the like.
• Do not throw the batteries in re!
• Attention should be drawn to the environmental aspects of battery disposal.
•
If the remote control is not going to be used for a long time, remove the battery to avoid
damage caused by battery leakage corrosion.
• Please respect the environment. Before throwing any batteries away, consult your
distributor who may be able to take them back for specic recycling.
GB - 3 GB - 4
GB - 10 GB - 11
GB - 12
GB - 13
Important safeguards
Note:
1. Only Speakers with 4 ohms impedance may be used.
2. Ensure that the blue automatic antenna cable does not make contact with any
ground connection.
3. Do not use AV IN jack on front panel & RCA terminal at the back at the same time
for the AUX source.
4. When Rear view camera function is ON, panel buttons are locked and sound is off
but music continues reading in DVD/USB/SD card.
The Description of the Wiring Diagram for Socket 2
When you unpack your new car radio, make sure that you have removed all the
accessories and information papers:
Main unit with connector
User manual
Accessories:
To adjust the sound settings
To adjust the sound settings, press SEL button repeatedly to select “BAS” (BASS),
“TRE”(TREBLE), “BAL” (BALANCE), “FAD”(FADER) or “VOL”(VOLUME). Then press
VOLUME+/- buttons on remote control or rotate volume knob on main unit to adjust
the value.
ESP function
The ESP (Electronic Shock Protection) works for all formats of discs.
Select chapter/track with the number buttons
When playing DVD/MP3/CD discs, press one of the 1~9 and the 0/10 number buttons
to directly select and play the 1st to 10th track / chapter (the 0/10 button is used as
the 10 button).
If you want to play the track/chapter with serial number bigger than 10, use the 10+,
1~9 and 0/10 button.
Example 1, to play the 13th track/ chapter, firstly press the 10+ button once, then
press the 3 button.
Example 2, to play the 30th track/chapter, rstly press the 10+ button for 3 times, then
press the 0/10 button.(the 0/10 button is used as the 0 button)
Note: pressing and holding the +10 or -10 buttons will allow you to play the next 10 or
last 10 chapter/track (MP3 only).
LISTENING TO THE RADIO
Selecting Band
In radio mode, repeatedly press BAND button to select bands in following order: FM1
-> FM2 -> FM3 -> MW1 -> MW2.
Manual tuning
Briey press or button to manually search up or down with step by step for
your desired station from the current frequency.
Automatic tuning
Long press or button to automatically search up or down for an available
station from the current frequency.
APS function
In radio mode
1) When pressing and holding the APS button, the radio searches on the current band
for the strongest signal stations and stores them automatically in memory. It can store
up to 18 stations in FM (6x FM1, 6x FM2 and 6x FM3) and 12 in MW (6x MW1 and 6x
MW2).
2) When pressing briey the APS button, the radio plays each preset station for a few
seconds. When completed, it will remain on the 1st memory.
English
The Description of the Wires Connection.
The Description of the Wiring Diagram for Socket 1
Press MODE button repeatedly to select RADIO mode.
Alternative Frequencies (AF)
When pressing the AF button briey, the AF switching mode is selected and the state
of the AF switching mode is displayed by AF segment in display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and receive RDS information.
Segment ashing: AF switching mode on, but RDS information is not received yet.
When the AF switching mode is selected, the radio checks the signal strength of
alternative frequencies. Every time that a new AF is stronger than the current station,
it switches over to that frequency for very short time, and the NEW FREQUENCY
is displayed for 1-2 second. (When AF flashes on LCD, it will search for the
stronger RDS station. If AF and TP flash on LCD, it can only search for the traffic
announcement station).
Trafc Announcement (TA)
Press the TA button shortly to turn on TA search mode.
When trafc announcement is transmitted:
1).If the unit is in Disc Play mode, it will switch to radio mode temporarily.
2).If the unit is in radio mode, it will switch automatically to the trafc announcement.
* TA interruption function: The current trafc announcement is cancelled by pressing
TA button shortly.
* When TA is on, SEEK (SCAN), AUTO MEMORY (APS) function can be received or
saved only when trafc program identication code has been received.
Region Management Information
Region Management Information: This unit is designed and manufactured to respond
to the Region Management Information that is encoded on DVD discs. If the Region
number printed on the DVD disc does not correspond to the Region number of this
unit, this unit cannot play that disc.
The region number of this unit is 2.
BASIC PLAYBACK
1. Press PWR button to turn on the unit.
2. Press OPEN button to open the touch screen.
3. Insert a disc with label facing up.
4. It takes a short while for your unit to load the disc. After loading, the unit will
automatically bring you to the main menu of the DVD or start playing the DVD. If the
unit does not automatically start playing the DVD, press .
Accelerated play
While the disc is playing, tap or icon on touch screen one or more times to
vary the speed and direction of the accelerated play. Press to resume normal
playback.
ADVANCED FUNCTIONS
On screen display
While the disc is plying, press OSD button repeatedly to display the playback information .
Search a desired section
You can access a specic location by keying in the target time or the track number.
1.Press SEARCH button to enter the search mode.
2.Use ◄ , ► and number buttons to input. Then press OK button to jump to the target
location immediately.
Note:Press CLEAR button to cancel the incorrect input.
• PLAY MODES
• Repeat playback
While the disc is playing, press the RPT button repeatedly to select a play mode:
DVD: Repeat Chapter, Repeat Title , Repeat All, Repeat Off;
CD: Repeat 1, Repeat All, Repeat Off.
MP3: Repeat 1, Repeat Directory, Repeat All, Repeat Off
Note:
* Some DVD discs do not allow repeat function.
* Skip function is not available for Repeat Chapter (DVD) , Repeat Track (CD) and
Repeat File (MP3 les).
A-B repeat
To repeat a sequence between two points A and B, press the A-B button at the
beginning of the sequence you want to repeat. Then press the A-B button again at the
end of the sequence. Then the sequence is played repeatedly until you press A-B to
resume normal playback.
Note: Some DVD discs do not allow A-B repeat function.
NOTE
1.For safety reasons, connect the parking line (GREEN) to the parking brake switch.
Video will be displayed only when the car is stopped and the parking brake is on.
2.If you don’t want to use this function, connect the wire to the ground.
5. Make sure to connect the color coded leads according to the diagram, incorrect
connections may cause the unit to malfunction or damage the vehicle’s electrical
system.
6. Do not connect the ignition wire (red) and the battery wire (yellow), it may cause a
short circuit, even result in re.
INSTALLATION
LOCATION OF THE CONTROLS
Disc and les you can play
In spite of progress made to ensure playability of all discs types, it is not possible to
guarantee playback of discs which are not in conformity with DVD, CD, VCD or SVCD
standards.
This unit may not play some recordings or les on CDs or DVDs due to differences in
recording formats, software used and disc types. The recordable discs may need a
longer reading time than normal discs.
Note: “INVALID KEY“ will be displayed if the function you select is not available.
The remote control operates on 1pc “CR2025” lithium battery (included).
To power up the remote control, remove the insulation tab from the back
of unit.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.
BASIC OPERATION
R33. TITLE/PBC button: To access the disc title menu. To turn PBC mode on/ off for
VCD.
R34. SUBTITLE button: To change the subtitle setting.
R35. PROG (Program)button: To program playback sequences.
R36. OSD button: To show status information on the screen.
R37. LOUD button (loudness): To turn ON/OFF loudness function.
R38. STEP button :To play frame by frame
To turn ON/OFF the unit
Press PWR button to turn on the unit. Long press PWR button to turn off the unit.
Note: When the unit is off. Pressing any button except REL can turn on the unit.
To open / close the touch screen
Press OPEN button to open or close the touch screen.
You can adjust the viewing angle of the screen with button on remote control.
To select function mode
- With front panel and remote buttons
* Press the MODE button to select RADIO, DISC (After inserting a disc), USB (After
inserting a USB device), Card (After inserting a MMC or SD card) or AV IN
- With the touch screen
* Tap icon on touch screen to display the main menu as shown below. Then tap
the icon to select your desired function mode.
To check the clock time
Press CLK button to check the clock time.
To select a preset EQ mode
Press the EQ button to select the preset music equalizer curves: POP, ROCK,
CLASS, EQ OFF.
To turn on/off LOUDNESS mode
Press the LOUD button to turn on/off LOUDNESS mode. When turning on
LOUDNESS mode, it will enhance bass level immediately when the bass is not
enough.
Manual preset
In RADIO mode:
1) To memorize the current frequency on the current band, press and hold any one of
the six preset buttons [1-6].
2) To recall the preset memory on the current band, press one of the preset buttons
[1-6].
FM Stereo
In FM radio mode, press ST button to turn on/off FM stereo mode.
LOC selector
During radio status, press LOC button to select strong or weak station reception. “LOC”
appears on the display and only local station is available. When" DX " appears, both
distance and local stations can be received.
• This function is only valid in FM.
RDS FUNCTION (Radio Data System)
Program type (PTY)
Press the PTY button shortly to select one of the PTY group. In a PTY group, press
the VOLUME+/- button on the remote control or rotate the VOLUME knob on the front
panel to select one of the PTY programs. (You can also use the number buttons 1-6
to select one of PTY programs.)
After selecting one of the PTY programs, it will display “SEEK PTY” and automatically
search for the station of the PTY program. If the station of the PTY program does not
exist, it will display “PTY NONE” and then return back to the current station.
DISC PLAYBACK
Frame advance (DVD)
1.While the disc is playing press STEP button once.
2.Press STEP a number of times to advance forward image by image.
3.Press to resume normal playback.
Variable slow motion (DVD)
1.While the disc is playing, press SLOW_FWD button.
2.Press the SLOW_FWD button repeatedly to change slow speed.
3.Press to resume normal playback.
Changing chapter/track
While the disc is playing, press or to go immediately to the next or previous
chapter (DVD), or to the next or previous track (CD).
Zoom (DVD)
While a disc is playing, press ZOOM until you reach the zoom size you want. The
button cycles through 2x, 3x, 4x and then zooms out to 1/2x ,1/3x,1/4x, then returns to
normal playback.
Remote control
R1. PWR (Power) button : To turn unit on /off
R2. EQ/OPEN button : To select the desired
preset equalizer ROCK, POP & CLASS.
To open/close the touch screen.
R3.
BAND button : To select band: FM1, FM2,
FM3 , MW1 or MW2.
R4. (Screen angle) button: To adjust the
screen angle.
R5. MUTE button : To mute or restore sound.
R6.
SEL (Select) button: To adjust the sound
setting.
R7. VOLUME+/- button: To adjust the volume.
R8.
MODE button: To select function mode : RADIO,
DVD, CARD, USB or AV IN.
R9.
SETUP button: To enter the Setup menu
R10. MENU button: To access disc menu.
R11. ▲button : Move up during menu navigation.
R12. ▼button : Move down during menu navigation.
R13. ►button: Move right during menu navigation.
R14. ◄button: Move left during menu navigation.
R15. OK button: To conrm the selection during
menu navigation.
R16. button: To directly access the next
chapter (DVD) or track (CD).
R17. button: To stop playback.
R18. (play/pause) button: To start or pause playback.
R19. button: To directly access the previous chapter (DVD) or track (CD).
R20. Number buttons (1,2…0/10)
TA (Trafc announcement) : To access TA mode.
AF (Alternative frequency) : To access AF mode.
6/+10 : Short press for number 6. Long press to skip forward 10 tracks (mp3 only).
5/-10 : Short press for number 5. Long press to skip backward 10 tracks (mp3 only).
R21. CLK (clock)button : To check the clock time.
R22. 10+/PTY button: To access PTY mode.
R23. LOC/SLOW-FWD button: To access LOC function. To play at slow motion.
R24. (Camera angle)/ST button : To access the camera angle function for DVD
disc. To turn ON/OFF FM stereo mode.
To reset the unit
Operating the unit for the rst time or after replacing the car battery, you must reset
the unit.
Release the front panel rst, and then press RESET button with a pointed object (such
as a ballpoint pen) to set the unit to initial status.
Note: When some errors occur on the display, you can also press RESET button to
resume to normal, and it will erase the clock setting and some memorized functions.
Program playback (DVD and CD)
With this option, you choose and program the playback order.
1. Insert a disc.
2. In playing or stop mode, press the PROG button. The Program menu appears.
3. Use ◄ , ► , ▲ , ▼ and number buttons to input.
4. Repeat step 3 until programming is completed.
5. Highlight the "PLAY" icon, then press OK button to start the program play.
6. Press the PROG button twice to cancel program playback.
Random playback (DVD, CD, MP3)
During normal playback, press RDM button to start random playback. “RANDOM :
ON” appears on screen for few seconds. To cancel random playback, press RDM
button again. “RANDOM : OFF” appears on screen for few seconds.
Intro playback (CD & MP3)
During playback, press INT button to play the rst 15 seconds of each track. Press
INT again to cancel this function.
USB OR SD/MMC PLAYBACK
You can connect a USB ash drive (not included) to the USB connector port or a SD/
MMC card (not included) to the memory expansion card slot on the unit to play MP3/
MP4/JPEG les.
• Connect your USB device to the USB port with the supplied USB cable.
• Press REL button to remove the front panel of unit and insert a SD/MMC card to the
card slot. Put the front panel back in place.
• Select USB or CARD mode with MODE button.
For operation of playing les on the USB ash drive or SD/MMC card, please refer to
the section "PLAYING MP3/MP4/JPEG FILES"
Note:
*There are many USB devices in the market. We cannot guarantee to support all
different models. Please try another USB device if your device is not supported.
* Some SD/MMC card may be incompatible.
PLAYING MP3/MP4/JPEG FILES
This unit can play MP3, MP4 and JPEG les recorded on CD-R/CD-RW discs, USB
ash drive and SD/MMC card.
1. Insert a disc. Playback starts automatically.
2. To select a le, tap to display content list.
1. OPEN button: To open/close the touch screen.
2. PWR/MUTE button: To turn unit on /off. To mute or restore sound.
3. Touch screen
4. AV IN jack
5. Disc Slot
6. USB port
7. SD/MMC Card Slot
8. MODE button: To select function mode : RADIO, DVD, CARD, USB or AV IN.
9. Volume knob : To adjust the volume.
10. button: To directly access the previous chapter (DVD) or track (CD).
11. button: To directly access the next chapter (DVD) or track (CD).
12. 1/ (Play/pause) button: To select preset channel 1 in radio mode. To start or pause playback.
13. 2/ INT (Intro) button: To select preset channel 2 in radio mode. To start/ cancel intro playback.
14. 3/ RPT (Repeat) button: To select preset channel 3 in radio mode. To repeat playback.
15.
4/ RDM
(Random) button: To select preset channel 4 in radio mode. To start/ cancel random
playback.
16. 5/ -10 button: To select preset channel 5 in radio mode. To skip backward 10 tracks (mp3 only).
17. 6/+10 button To select preset channel 6 in radio mode. To skip forward 10 tracks (mp3 only).
18. BAND button: To select band: FM1, FM2, F3, MW1 or MW2.
19. APS button: To auto preset radio stations.
20. EJECT button : To eject the disc from disc slot.
21. RESET button : To reset the unit.
22. Small LCD display
23. Remote Sensor
24. REL (Release) button: Press to release the front panel.
