722677
9
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
Operating Instructions for RX-7-DR M-LINK /
RX-9-DR M-LINK 2.4 GHz receivers
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestre 1 • D-75015 Bretten (Gölshausen) www.multiplex-rc.de Page 1/6
Instructions for RX-7/9-DR M-LINK 2.4 GHz receivers # 985 5319 (10-02-24/MIWA) • Errors and omissions excepted! •
¤
MULTIPLEX
!These operating instructions are an integral part
of the product, and contain important information
and safety notes. Please store them in a safe place,
where you can find them at any time, and pass
them on to the new owner if you sell the receiver.
1. SPECIFICATION
RX-7-DR M-LINK RX-9-DR M-LINK
Order No. # 5 5811 # 5 5812
Reception system
2.4 GHz FHSS M-LINK
Frequency Hopping Spread Spectrum
MULTIPLEX-LINK
Servo channel count 7 9
Servo frame rate Fast Response: 14 ms
Standard: 21 ms
Signal resolution 12-bit, 3872 steps
Current drain Approx. 60 mA (excl. servos)
Aerial length Total: approx. 20 cm (2 x),
of which feed cable approx. 17 cm and
active aerial section approx. 3 cm
Operating voltage 3.5 V … 9.0 V
Î 4 - 6 NiCd / NiMH (NiXX) cells
Î 2S LiPo / LiIo
Operating
temperature range - 20°C … + 55°C
Weight 19 g
Dimensions Approx. 49.0 x 34.0 x 11.5 mm
2. SPECIAL FEATURES
x High-quality 7-channel / 9-channel receivers assembled
using the latest SMT methods, exploiting MULTIPLEX
2.4 GHz M-LINK technology, suitable for all types of model.
x Dual receivers:
Each receiver features two complete reception circuits
working in parallel (receiver diversity).
This ensures excellent reception quality by minimising
directional effects.
x Supplementary signal pre-amplification:
For highest possible sensitivity.
x In-line connector arrangement:
Ideal for models with limited internal space.
x HOLD / FAIL-SAFE function.
x Integral SET button and LED:
For binding, FAIL-SAFE programming, RESET and
displaying operating status information.
x Telemetry / feedback channel capability:
Receiver battery voltage and connection quality
= standard features.
Integral sensor interface for connecting external sensor
modules.
x Prepared for two-receiver operation:
Diversity lead (# 8 5070) required.
x Integral error counter / data logger:
For voltage and signal errors.
x Compatible with the MULTImate (# 8 2094).
x Integral PC interface:
Carry out updates and change settings using the
RX DataManager PC program.
3. SAFETY NOTES
!Please read the instructions before using the receiver.
!Use the receiver only for the intended applications
(Î 4.).
!Ensure the power supply is of adequate capacity (Î 6.).
!Observe the installation notes (Î 18.).
!Carry out regular range checks (Î 13.).
4. APPLICATIONS
The RX-7-DR M-LINK and RX-9-DR M-LINK 2.4 GHz receivers
(abbreviated to RX-7/9-DR M-LINK in this document) are radio
control receivers intended exclusively for use in model sport. It is
prohibited to employ them for other purposes such as full-size
(people-carrying) vehicles or industrial installations.
5. COMPATIBILITY
RX-7/9-DR M-LINK 2.4 GHz receivers can only be operated in
conjunction with transmitters which utilise MULTIPLEX M-LINK
transmission technology.
These are as follows (correct as of February 2010):
xROYALpro 7,9 and 16 M-LINK.
xROYALevo or pro 7,9 and 12 with firmware version V3.xx
and the HFM4 M-LINK 2.4 GHz RF module*.
xPROFImc 3010,3030 and 4000 with the HFM3 M-LINK
2.4 GHz RF module*.
xCOCKPIT SX M-LINK.
xMULTIPLEX transmitters with the HFMx M-LINK 2.4 GHz
RF module.
!*Note:
Unless stated otherwise, when this document refers to the
transmitter types ROYALevo,ROYALpro, and PROFImc 3010,
3030 and 4000, the terms refer to the 2.4 GHz M-LINK versions.
6. POWER SUPPLY
RX-7/9-DR M-LINK receivers work within a broad range of vol-
tages from 3.5 V 9.0 V, i.e. they can be used with receiver
batteries consisting of four to six NiXX cells or 2S LiPo / 2S LiIo.
! Note: if you intend to use a five-cell or six-cell NiXX battery,
or a 2S LiPo or 2S LiIo pack, it is essential to check that all the
servos, gyros and other components connected to the system
are approved for use with this higher operating voltage.
!Note: ensure that the power supply is adequate
A power supply system in good condition and of adequate capa-
city for the specific application plays an indispensable role in the
safe operation of any model:
x Use only high-quality receiver batteries of adequate capacity.
Balance and maintain them carefully, and charge them fully.
x Ensure that all cables are of adequate conductor cross-
section. Keep all wiring as short as possible, and use the
absolute minimum of plug / socket connections.
x Use high-quality switch harnesses exclusively.
x Brief collapses in the power supply voltage (lasting a few
milli-seconds) have no adverse effect on the receiver. Longer
voltage collapses to below 3.5 V may cause a receiver reset,
resulting in a brief interruption in reception. This may be due
to a receiver battery which is almost flat, too weak or
defective, cables of inadequate cross-section, poor-quality
connectors or an overloaded or defective BEC system.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Multiplex RX-9-DR M-LINK bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Multiplex RX-9-DR M-LINK in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info