Handleiding Multiplex FunCub 21 4243 (pagina 10 van 40) (Duits, Engels, Frans, Italiaans, Spaans)

561585

Verklein

Vergroot

Pagina terug

1/40

Pagina verder

Important note

This model is not made of styrofoam™, and it is not possible to glue the material using white glue, polyurethane or

epoxy; these adhesives only produce a superficial bond which gives way when stressed. Use medium-viscosity

cyano-acrylate glue for all joints, preferably our Zacki-ELAPOR®, # 59 2727 - the cyano glue optimised specifically for

ELAPOR® particle foam.

If you use Zacki-ELAPOR® you will find that you do not need cyano ‘kicker’ or activator for most joints. However, if

you wish to use a different adhesive, and are therefore obliged to use kicker / activator spray, we recommend that

you apply the material in the open air as it can be injurious to health.

1. Before assembling the model

Please check the contents of your kit before you start working

on it. You will find Figs. 1 + 2 and the Parts List helpful here.

2. The fuselage

The first step is to glue the latch catches 22 and the motor

mounts 37 in both fuselage shells.

Fig. 3

3. Installing the servos

Check that the elevator and rudder servos are a snug fit in the

fuselage shells 3 + 4 and apply a drop of glue to the mounting

lugs to secure them. Fix the servo leads in place using paper

masking tape, so that the wires and connectors cannot cause

damage, and do not get in the way when the shells are joined.

Fig. 4

4. Control “snakes”

Prepare the control snakes 54 / 56 and 55 / 57: cut the outer

and inner sleeves to length, and slip the steel pushrods 52 /

53 inside them. Install the swivel pushrod connectors in the

outermost hole of the rudder and elevator horns. Note that the

pre-formed pushrod end should be connected to the second

hole from the outside of the servo output arm. Lay the fuselage

shells down flat so that they are not distorted.

Figs. 5 - 6

5. Preparing the wing spreader plates

Clip together the wing spreader plates 33 + 34, using a pair of

flat-nose pliers if necessary, and glue the joints. Glue the

prepared wing spreader plates in the right-hand fuselage

shell.

Fig. 7

6. Joining the fuselage shells

Offer up the fuselage shells 3 / 4, initially without glue. When

you are confident that everything fits properly, the shells can be

glued together. Keep the fuselage perfectly straight while the

glue is curing.

Fig. 7

7. Preparing the elevator pushrod connector

Fit the swivel pushrod connector 25 for the elevator 8 in the

outermost hole of the elevator horn 24, and secure it with the

washer 26 and nut 27. Caution: take care to fit the connector

with the barrel on the outside (see drawing). Be careful when

fitting the retaining nut: tighten it just to the point where the

barrel rotates smoothly, but without lost motion, and then use

the point of a needle to apply a tiny drop of cyano or paint to the

nut threads to prevent it working loose. Fit the socket-head

grubscrew 28 in the swivel pushrod connector 25 using the

allen key 29. Glue the horn 24 in the recess of the elevator 8,

with the row of linkage holes facing forward.

Fig. 8

8. Attaching the tailplane

Place the tailplane on the fuselage “dry” - without glue - and

check that it is possible to set it exactly horizontal; minor

trimming to the tailplane saddle might be necessary. When

you are satisfied, glue the tailplane in place, and immediately

align it accurately. Fig. 9

9. Fin and tailwheel unit

Fit the steel wire tailwheel unit 76 through the glue-fitting

tailwheel bracket 36 and the glue-fitting rudder horn 35. Bend

the straight end of the wire through 90°, as close to the horn

surface as possible, as shown in Fig. 10.

Glue the rudder horn 35 in the slot in the rudder, but only apply

cyano to the bottom surface. Allow the glue to harden, then cut

a slot about 1.5 mm wide above the horn to accept the tailwheel

wire. Wipe off any excess adhesive. Rotate the wire tailwheel

unit 76 until it is located over the rudder horn 35, and align the

parts carefully before gluing it in place with a little cyano. Install

the swivel pushrod connector, and lock the nut with a drop of

paint or glue as previously described.

Fig. 11

Install the tailwheel 77 as shown: fit one wheel retainer (tubular

rivet) 78 on the wire axle, followed by the wheel, and finally the

second retainer.

Fix both wheel retainers 78 to the axle with a drop of cyano.

Fig. 12

10. Gluing the fin to the fuselage

Check that the fin assembly is a snug fit in the fuselage and

tailplane, and glue it in place as shown.

Fig. 13

11. Main undercarriage

The main undercarriage 70 can now be prepared for

installation:

Slip a collet 72 onto each axle (right and left), and secure them

with the socket-head grubscrews 73. Fit the wheels 71 on the

axles and secure them with two further collets 72 and

grubscrews 73. Adjust the collet spacing to ensure that the

wheels rotate freely. Fig. 15

The undercarriage bracket 74 can now be glued to the

underside of the fuselage: press it in firmly before applying the

adhesive. Fig. 14

Push the main undercarriage unit 70 into the bracket until it

engages, then fit the retaining screw 75 to secure it.

Fig. 15

12. The wings

The wing panels 6 / 7 should

not be glued together!

Before you install the spars in the wings, offer up the tubular

spars 50 / 51 and the spar joiners 30 / 31 “dry” to check that the

parts fit neatly.

Please note: the front spar joiner 30 is deeper than the rear

joiner 31.

When you are confident that everything fits properly, glue the

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Multiplex FunCub 21 4243 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info