683949
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
BA EA3632knx Hardware HM;DE,GB -23830- 2017.11V02 ED.doc
INSTRUCTION MANUAL INPUT/OUTPUT MODULE EA 36.32 KNX HUGO MÜLLER GMBH & CO KG, STURMBÜHLSTR. 145-149, 78054 VS-SCHWENNINGEN
SAFETY INSTRUCTIONS AND BASICS
EA 36.32 knx
Service:
Hugo Müller GmbH & Co KG
Sturmbühlstraße 145-149
D-78054 VS-Schwenningen
Germany
+49 7720 80836
www.hugo-mueller.de
Technical data
Safety instructions / Intended use
Power supply:
Bus current:
24 V DC (via KNX bus voltage)
< 10 mA
CAUTION! DANGER OF FIRE AND ELECTRIC SHOCK!
!!!Installation and assembly of electrical equipment must be carried out only by a skilled person!!!
Bus system:
KNX-TP/S
Connect only to suitable supply voltage [KNX bus voltage (nominal voltage 29V)].
Warranty void if housing opened by unauthorized person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if external in fluences
exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with national building, electrical and safety codes!
Defective devices / sensors have to be put out of service immediately!
Observe the regulations and instructions in the ZVEI/ZVEH handbook (building system technology). Especially the professional
installation of the bus lines and the professional installation and start -up of KNX devices must be observed!
The device fits for the particular use of the following tasks: monitoring of the air quality in building systems technology (schools,
offices, hotels, conference venue etc.), data transfer and regulation via bus system.
The device is intended for use in accordance with the defined technical data.
Operate the device exclusively in a dry room!
The device is not qualified for security relevant tasks such as emergency doors, fire protection equipment, fermenting cellar s etc.
Inputs:
3x binary Inputs (INPUT 1 / 2 / 3)
Input 2/3 can also be used as Input for external
temperature probes (PT1000 / Müller TF06). This
function requires use of both Inputs (2 and 3).
Outputs:
2x outputs (OUTPUT 1, OUTPUT 2)
- Can be configured as LED-driver (< 3 mA)
- Can be configured as Open-collector output
with the following specifications:
ext. supply voltage (U
max
) = 50 V DC
max. switching current (I
max
) = 80 mA
max. switching power (P
max
) = 200 mW
Voltage level on low signal = 0,5 V DC
Permitted ambient temperature:
-5°+45 °C
Housing:
self-extinguishing thermoplastic
Mounting:
Flush-mount (hollow-wall box)
Type of connection:
KNX bus terminal
Type of protection:
IP 20 to DIN EN 60529
Class of protection:
III when installed according to regulations
Inappropriate use / disposal
Input / Output Description (examples)
The device is not intended for use of unauthorized constructional alterations , repairs
and security relevant tasks.
The device is not intended for use in outdoor areas or wet rooms.
The device is not qualified for security relevant tasks. The intended use of the device is
only for comfort functions in home automation systems.
The inappropriate use of the device can cause damage to property and persons .
The device has to be disposed in an environmentally friendly manner according to the
current electrical codes!
Assembly
Disconnect device from power supply for wiring and installation
purposes! Check power supply is disconnected!
Attention! You have to check and consider the safety instructions above!
This device is suitable for mounting in a flush-mounting box.
Ensure that no dust gets inside of the device.
STEP 1: Connect the required inputs / outputs according to the schematics diagram.
STEP 2: Connect the KNX bus cable according to the color-coded connectors.
STEP 3: After wiring, press the programming buttonto set the device into
programming mode for addressing & configuration via ETS application.
STEP 4: Place / install device into the hollow-wall box.
Installation note: Make sure that no wires are pinched or squeezed when placing the device into the hollow-wall box.
Inputs configured as binary inputs
Outputs configured as LED drivers
Input 1 = binary input, Input 2/3 = temperature probe input
Outputs configured asopen-collector
Uext.:
Umax= 50 V DC
Imax = 80 mA
Pmax = 200 mW
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Muller EA 36.32 knx bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Muller EA 36.32 knx in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info