4890
9
Verklein
Vergroot
Pagina terug
1/50
Pagina verder
13
- Set the temperature adjustment control (J)
to MAX. Plug in the iron. As soon as the
temperature adjustment indicator (I) goes
out, unplug the iron and place it over the sink.
Turn the steam adjustment control (C) to the
auto-clean position
and hold down the
control. Allow the tank to empty. The mix-
ture of water/steam will carry away the scale
residues contained in the soleplate.
- Then reset the steam adjustment control (C)
to position
.
- Using slow, deliberate movements, swing the
iron from left to right to give the soleplate a
good rinse and to remove the water
remaining in the soleplate. Empty the iron.
- Plug in the iron again in order to dry the
soleplate: perform this operation over a cloth
(watch out for water splashes or steam being
ejected).
- After this operation, unplug the iron once
more.
- Clean the soleplate on a cloth made of thick,
clean, damp cotton, before putting away the
iron or before using it again (iron cold).
Storage
After each use:
- Unplug the iron.
- Empty the water tank.
- Set the steam adjustment control (C) to
position
.
- Allow the iron to cool down then wind the
power cable by making a loop of about 10
cm starting from the iron.
- Store it on its heel.
What to do if your appliance
does not work
Problems Causes Solutions
The iron does not Faulty power supply Check the socket
heat up
Temperature adjust- Adjust the tempe-
ment control (J) on rature adjustment
minimum control (J)
No steam and the Steam adjustment Adjust the steam
iron is hot control (C) is in adjustment control
position
(C) to the desired
rate
The tank is empty Fill it with water
No steam and the Soleplate tempera- Set the thermostat
iron is hot ture adjustment too (J) to the steam
low for «Aqua Stop» zone, at the same
model time adjusting the
temperature accor-
ding to the type of
fabric to be ironed.
Water is dripping out Iron used for steam Wait for the adjust-
of the holes in the before the indicator ment indicator (I) to
soleplate during use light (I) has gone out go out for the first
time before going
to steam position
Steam flow rate set Reduce the flow by
too high adjusting the steam
control (C)
The spray, the pres- The tank is empty Fill it with water
sing function or the
Perfectpoint are not
working
Large reduction in Iron is starting to Perform an “auto-
the steam flow scale up clean”
Tank almost empty Fill it with water
The iron is causing The water used con- Perform an “auto-
brown marks on the tains or did contain clean” operation
laundry organic residues and change the
water. To find out
more, please refer
to the section on
“Recommended
type of water”
Water is running out Iron has been stored Set the steam
of the holes in the flat with water in the control (C) to
soleplate when it tank and store the iron
has been put away standing on its
heel.
Empty the water
from the iron.
If you have followed all these instructions
and your iron still does not work, please
contact an approved Moulinex service
centre (see list in the “Moulinex Service”
booklet).
Ironing guide
WHAT TEMPERATURE TO USE
Please refer to the labels on your laundry to
find out the composition of the fabrics or
ironing instructions.
Fers ATOLL.Eu11 17/10/00, 16:2213
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Moulinex Atoll 100 A ER1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Moulinex Atoll 100 A ER1 in de taal/talen: Nederlands als bijlage per email.

De handleiding is 0,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info