Handleiding Motorola MBP10S (pagina 2 van 2) (Engels)

609904

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

9 10 11 12

13 14 15

2.5 Paging

If the parent unit is misplaced, press the FIND key on Baby unit.

The parent unit will emit a repeated beep tone for 30 seconds so that you can

locate it.

Press any key on the parent unit, or the

B again on the Baby unit, to stop paging.

3. Using the MBP10S

3.1 Volume adjustment on the Parent unit

There are 5 volume levels on the parent unit.

• Press

( to increase the volume level.

• Press

) to decrease the volume level.

NOTE

When you press ( or ) a beep is played at the volume level currently set,

but if you try to adjust beyond the maximum or minimum levels it will output a

double beep.

4. Disposal of the Device (environment)

At the end of the product lifecycle, you should not dispose of this

product with normal household waste, but take the product to a

collection point for the recycling of electrical and electronic equipment.

The symbol on the product, User’s Guide and/or box indicates this.

Some of the product materials can be re-used if you take them to a

recycling point. By reusing some parts or raw materials from used

products you make an important contribution to the protection of the environment.

Please contact your local authorities in case you need more information on the

collection points in your area.

Dispose of the batteries in an environmentally-friendly manner according to your

local regulations.

5. Cleaning

Clean the MBP10S with a slightly damp cloth or with an anti-static cloth. Never use

cleaning agents or abrasive solvents.

Cleaning and care

• Do not clean any part of the product with thinners or other solvents and

chemicals –- this may cause permanent damage to the product which is not

covered by the warranty. When necessary, clean it with a damp cloth.

• Keep your MBP10S away from hot, humid areas or strong sunlight, and do not

let it get wet.

• Every effort has been made to ensure high standards of reliability for your

MBP10S. However, if something does go wrong, please do not try to repair it

yourself –- consult Customer Service for assistance.

6. Help

If the baby unit has lost its link with the parent unit

• Try recharging or replacing the batteries.

• If the baby unit is too far away it may be going out of range, so move the baby

unit closer to the parent unit.

• Reset the units by unplugging the units’ electrical power. Wait for around 15

seconds before plugging back in. Allow up to one minute for the baby unit and

the parent unit to synchronise.

Interference

Noise interference on your parent unit

• Your baby and parent units may be too close. Move them further away from

each other.

• Make sure there is at least 3.5 feet between the 2 units to avoid feedback

howling.

• If the baby unit is too far away it may be going out of range, so move the baby

unit closer to the parent unit.

• Make sure the baby and parent units are not near other electrical equipment,

such as a television, computer or cordless/mobile telephone.

7. General Information

If your product is not working properly....

1. Read this User’s Guide.

2. Visit our website: www.motorola.com

3. Contact Customer Service at:

US and Canada: 1-888-331-3383

To order a replacement battery pack for parent unit, contact customer service.

Consumer Products and Accessories

Limited Warranty ("Warranty")

Thank you for purchasing this Motorola branded product manufactured under

license by Binatone Electronics International LTD ("BINATONE")

What Does this Warranty Cover?

Subject to the exclusions contained below, BINATONE warrants that this Motorola

branded product ("Product") or certified accessory ("Accessory") sold for use with

this product that it manufactured to be free from defects in materials and

workmanship under normal consumer usage for the period outlined below. This

Warranty is your exclusive warranty and is not transferable.

Who is covered?

This Warranty extends only to the first consumer purchaser, and is not transferable.

What will BINATONE do?

BINATONE or its authorized distributor at its option and within a commercially

reasonable time, will at no charge repair or replace any Products or Accessories

that does not conform to this Warranty. We may use functionally equivalent

reconditioned/ refurbished/ pre-owned or new Products, Accessories or parts.

What Other Limitations Are There?

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS

LIMITED WARRANTY, OTHERWISE THE REPAIR OR REPLACEMENT

PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE

REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL MOTOROLA OR

BINATONE BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING

NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF

THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL,

SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF

2.3 Parent unit power supply

1. Connect the small plug of the power adapter to the power connector on the

parent unit and the other end of the adapter to the power outlet (100V-240V ~ 50/

60Hz).

NOTE

Only use the enclosed adapter (5V DC/600mA).

2. Press and hold

P. The Power (ON / ) LED will illuminate red when it is

connected to power supply.

3. Press and hold

P to switch off the parent unit.

2.4 Link

NOTE

Do not place the baby unit or cables in the crib or within arm’s reach of the baby

(the unit should be at least 3.5 feet away).

When using the baby monitor for the first time, it is advised to test the connection.

• Install the parent unit in the same room as the baby unit, but make sure there is

at least 3.5 feet between the 2 units.

• When both units are switched on, the parent unit will search for the baby unit.

• The green link LED on the parent unit will flash until the parent unit is

connected with the baby unit.

Once the link is established, the LED will stop flashing.

• The sound captured by the microphone on the baby unit will be audible on the

parent unit.

• The detected sound level is indicated by the LEDs on the front of the parent unit.

• When the connection is established, move the parent unit to the room you want

to monitor from, but within the operational range.

• When there is no connection or the unit is out of range, the parent unit emits a

warning beep every 20 seconds and the green link LED on the parent unit will

flash.

• Move the parent unit closer until the link is re-established.

Communication Services. Defects, damages, or the failure of Products or

Accessories due to any communication service or signal you may subscribe to or

use with the Products or Accessories is excluded from coverage.

How to Obtain Warranty Service or Other Information?

To obtain service or information, please call:

US and Canada 1-888-331-3383

You will receive instructions on how to ship the Products or Accessories at your

expense and risk, to a BINATONE Authorized Repair Center. To obtain service,

you must include: (a) the Product or Accessory; (b) the original proof of purchase

(receipt) which includes the date, place and seller of the Product; (c) if a warranty

card was included in your box, a completed warranty card showing the serial

number of the Product; (d) a written description of the problem; and, most

importantly; (e) your address and telephone number.

These terms and conditions constitute the complete warranty agreement between

you and BINATONE regarding the Products or Accessories purchased by you, and

supersede any prior agreement or representations, including representations

made in any literature publications or promotional materials issued by BINATONE

or representations made by any agent employee or staff of BINATONE, that may

have been made in connection with the said purchase.

FCC and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the Federal Communications

Commission (FCC) rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation. Privacy of communications may not be ensured

when using this device.

To ensure safety of users, the FCC has established criteria for the amount of radio

frequency energy that can be safely absorbed by a user or bystander according to

the intended usage of the product. This product has been tested and found to

comply with the FCC criteria. The Baby unit shall be installed and used such that

parts of the user’s body other than the hands are maintained at a distance of

approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian ICES-003.

WARNING

Changes or modifications to this equipment not expressively approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

Industry Canada

Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

The term "IC: " before the certification/registration number only signifies that the

Industry Canada technical specifications were met.

This product meets the applicable Industry Canada technical specifications.

RENSEIGNEMENTS RELATIFS AUX RÈGLEMENTS DE LA

COMMISSION FÉDÉRALE DES COMMUNICATIONS ‘FCC’,

ET D’INDUSTRIE Canada ’IC’

Article 15 des reglements du FCC

AVIS: Cet équipement a été testé et s’est révelé conforme aux limites d’un appareil

numérique de classe B, conformément à la Section 15 du réglement de la Federal

Communications Commission (FCC). Ces limites sont conçues pour offrir une

protection raisonnable contre toute interférence nuisible sur une installation

résidentielle. Cet appareil génère, utilise et peut émettre des fréquences radio et

s’il n’est pas installé selon les instructions, peut nuire aux radiocommunications.

Toutefois, rien ne garantit que des parasites ne surviendront pas dans une

installation particulière. Si cet appareil cause des interférences nuisibles à la

réception du téléviseur ou de la radio, ce que vous pouvez déterminer en mettant

votre appareil en et hors fonction, nous vous invitons à essayer l’une des mesures

correctives suivantes :

• Réorientez l’antenne de réception.

• Éloignez l’appareil du composant qui reçoit les ondes.

• Branchez l’appareil dans une prise de courant CA différente de celle du

composant qui reçoit les ondes.

• Au besoin, consultez votre marchand électronique ou un technicien spécialisé

dans le service des radios/téléviseurs pour des suggestions supplémentaires.

Toute modification ou changement effectué à cet appareil sans l’accord des parties

responsables de l’homologation peut retirer à l’utilisateur son droit d’utiliser l’appareil.

Cet appareil est conforme à l’article 15 de la FCC. Le fonctionnement est soumis

aux deux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences

nuisibles et; (2) Il doit pouvoir supporter les parasites qu’il reçoit, incluant les par

sites pouvant nuire à son fonctionnement. La confidentialité des communications

peut ne pas être assurée avec cet appareil.

Afin de garantir la sécurité des utilisateurs, la FCC a établi les critères relatifs à

l’énergie générée par les fréquences radio pouvant être absorbée en toute sécurité

par un utilisateur ou par quelqu’un se trouvant à proximité, dépendamment de

l’utilisation prévue du produit. Ce produit a été testé et s’avère conforme aux

normes de la FCC. L’unité du bébé devra être installée et utilisée de manière à ce

que le corps de l’utilisateur, à l’exception des mains, soit toujours à une distance

d’environ 20 cm (8 po.) ou plus.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

AVERTISSEMENT

Tout changement ou modification à cet équipement, non expressement autorisé

par la partie responsable de la conformité, pourrait annuler l’autorisation donnée à

l’utilisateur d’utiliser cet équipement.

Industrie Canada

Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne

doit pas causer d’interférences nuisibles et; (2) Cet appareil accepte toute les

interférences dont celles qui pourraient provoquer le fonctionnement involontaire

de l’appareil.

L’abréviation ’IC’ se trouvant avant cette homologation signifie que la certification

fut effectuée selon une déclaration de conformité spécifiant que les normes

d’Industrie Canada ont été rencontrées.

Cet appareil est conforme aux spécifications techniques d’Industrie Canada.

Technical Specifications

Frequency range 2.40 to 2.48 GHz

Electrical power Parent and Baby units:

Input

: 100-240VAC, 50/60Hz (USA plug);

Output: 5VDC, 600 mA

(Supplier: 5ESP, Model: 5E-AD050060-U;

Supplier: GPE, Model: GPE003W-050060-1)

Parent unit:

2.4V 600 mAh Ni-MH rechargeable battery pack

(Supplier: BYD, Model: H-AAA600BX2-CT;

Supplier: GPI, Model: GPRHC063N118;

Supplier: SANIK, Model: AAA600)

REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR

OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE

ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE

FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.

Some jurisdictions do not allow the limitation or exclusion of incidental or

consequential damages, or limitation on the length of an implied warranty, so the

above limitations or exclusions may not apply to you. This Warranty gives you

specific legal rights, and you may also have other rights that vary from one

jurisdiction to another.

Exclusions

Normal Wear and Tear. Periodic maintenance, repair and replacement of parts

due to normal wear and tear are excluded from coverage.

Batteries. Only batteries whose fully charged capacity falls below 80% of their

rated capacity and batteries that leak are covered by this Warranty.

Abuse & Misuse. Defects or damage that result from: (a) improper operation,

storage, misuse or abuse, accident or neglect, such as physical damage (cracks,

scratches, etc.) to the surface of the product resulting from misuse; (b) contact with

liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like,

extreme heat, or food; (c) use of the Products or Accessories for commercial

purposes or subjecting the Product or Accessory to abnormal usage or conditions;

or (d) other acts which are not the fault of MOTOROLA or BINATONE, are excluded

from coverage.

Use of Non-Motorola branded Products and Accessories. Defects or damage

that result from the use of Non-Motorola branded or certified Products or

Accessories or other peripheral equipment are excluded from coverage.

Unauthorized Service or Modification. Defects or damages resulting from

service, testing, adjustment, installation, maintenance, alteration, or modification in

any way by someone other than MOTOROLA, BINATONE or its authorized service

centers, are excluded from coverage.

Altered Products. Products or Accessories with (a) serial numbers or date tags

that have been removed, altered or obliterated; (b) broken seals or that show

evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming

or non-Motorola branded housings, or parts, are excluded from coverage.

Products Covered Length of Coverage

Consumer Products One (1) year from the date of the products

original purchase by the first consumer

purchaser of the product.

Consumer Accessories Ninety (90) days from the date of the

accessories original purchase by the first

consumer purchaser of the product.

Consumer Products and

Accessories that are Repaired

or Replaced

The balance of the original warranty or for

ninety (90) days from the date returned to the

consumer, whichever is longer.

Manufactured, distributed or sold by Binatone Electronics International LTD., official licensee

for this product. MOTOROLA and the Stylized M Logo are trademarks or registered

trademarks of Motorola Trademark Holdings, LLC. and are used under license.All other

trademarks are the property of their respective owners.

Printed in China

Version 3.0

Motorola MBP10S Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Motorola MBP10S

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info