504527
38
Verklein
Vergroot
Pagina terug
1/81
Pagina verder
Installation 3-15
DCT5100 Installation Manual
When multiple OOB frequencies are used, the DCT5100 pauses 40 seconds on each valid
frequency. The LED displays dl and a progress indicator, which identifies a software object
download. The progress indicator, or crawling ant, moves one position around the dl display
for each segment of download received. If the dl stops moving up and down on the LED for
an extended period of time, contact the headend operator.
The progress indicator usually moves at a consistent rate as segment downloads are
received. If all the segments are retrieved in the first pass, the EF, AU and FP messages are
displayed on the LED. If segments are dropped, the progress indicator appears to stall and
then inch forward after the dropped segments are retired.
When the progress indicator alternates between rapid and sluggish movement, this may
indicate that the stream is spinning too fast for existing plant conditions.
The LED displays EF for up to 60 seconds when the software object download is complete
during flash erasure and then displays FP for up to 60 seconds during flash programming.
The DCT5100 is ready for initialization by the headend controller when the LED display is
blank. Verify that the DCT5100 is powered up or reset within two minutes of a completed
download.
Boot Cycle Error Codes
If hardware or software problems occur, the DCT5100 displays error codes on the LED display.
Table 3-2 is a list of error codes that can occur during boot cycle startup:
Table 3-2
Error codes at boot cycle startup
Error
Code
Description When error occurs Action Required
Eb 01
Object failed validation After the LED displays dl, indicating
validation check failed
Contact headend
operator
Eb 02
Download time-out After cycling twice through the OOB
frequencies
None
Eb 03
Flash erase failed After software object download complete
and EF is displayed
Replace DCT5100
Eb 04
Flash programming
failed
After software object download complete
and FP is displayed
Contact headend
operator
Eb 05
Invalid DLC frequency After the LED displays dl, indicating
validation check failed
Contact headend
operator
Eb 06
Hardware initialization
failed
After plugging the DCT5100 into an
electrical outlet to begin the boot cycle
Replace DCT5100
Eb 07
Object failed validation After software object download complete
and FP is displayed
After a successful software object
download and DCT5100 is reset
Contact headend
operator
No action required
because DCT5100
repeats software object
download process
Eb 08
Reserved None
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Motorola DCT5100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Motorola DCT5100 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Motorola DCT5100

Motorola DCT5100 Gebruiksaanwijzing - English - 58 pagina's

Motorola DCT5100 Gebruiksaanwijzing - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info