646335
14
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
• COMBUSTION GAS REMOVAL
Flue: A draught diverter is fitted to the top of the water heater. The nominal flue
size is 90 mm. (D61B, D61E) and 110 mm. (G11E). In exposed situations, twin-
walled flue pipe should be used. A minimum length of vertically rising flue of 600
mm. must be provided to ensure the water heaters products of combustion are
completely evacuated. If single wall flue pipe is being used which has to pass
through combustible materials, provide a metal sleeve of 115 mm. diameter which
allows an air gap of 25 mm.
The flue shall not run into chimneys for removing combustion products from solid
or liquid fuels. Flue pipes and terminals should comply with BS 715. Terminals shall
not be sited within 300 mm. of a ventilator or open window. In the U.K. full details of
flueing requirements are given in BS 5440 Part 1.
The flow rate of the combustion gases is 14 m³/h (G-30 and G-31) and 14.54 m³/h
(G-20 and G-25). The temperature of the combustion gases at the exit draught
diverter hood is 137°C (Model D61E, D61B).
The flow rate of the combustion gases is 41.4 m³/h (G-30 and G-31) and 44.4 m³/h
(G-20 and G-25). The temperature of the combustion gases at the exit draught
diverter hood is 160°C. (Model G11E).
This appliance is fitted with a safety device to monitor the removal of combustion
gases, which cuts off the supply of gas to the burner, thereby turning off the appliance.
The function of this device is to detect (thermally) if products of combustion are not
being removed to the outside air by the flue, due to adverse weather conditions
causing a down draught down the flue, blockage in the flue or problems with the
ventilation supplying the air for combustion.
This device should never be deactivated or removed, as this would compromise the
safety of the occupants in the event of flue gas spillage.
Whenever any repairs are made to this device, only original parts should be fitted.
A check should always be made to ensure that the appliance works correctly. The
procedure is as follows:
a) Turn the appliance on.
b) If air does not blow back through the flueway due to bad weather conditions
(too much wind), the control device should not stop the appliance, at least
during 30 minutes of continuous operation.
If this test is carried out satisfactorily, the appliance is in perfect operating condition.
If the appliance repeatedly turns off, this means that the combustion gases are not
being removed correctly. The problem should be resolved by taking the
appropriate steps.
• AIR SUPPLY FOR COMBUSTION
Air requirements: Reference is made to BS 5482 BS EN 1949 and EN 721 covering
ventilation requirements for permanent dwellings, caravans and boats.
Fixed ventilation should be provided to avoid draughts as far as possible without
impairing the free area of ventilation, even in adverse weather conditions. If the heater
is positioned in location which may be subjected to strong draughts i.e. close to a
window or opening then strong draughts or gusts of wind may extinguish the pilot.
14
14

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Morco-D-61B

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Morco D-61B bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Morco D-61B in de taal/talen: Engels als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Morco D-61B

Morco D-61B Gebruiksaanwijzing - Nederlands - 23 pagina's

Morco D-61B Gebruiksaanwijzing - Français - 23 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info