549867
64
Verklein
Vergroot
Pagina terug
1/79
Pagina verder
EN-64
Replacing the lamp
This projector is equipped with 2 lamps to project
images. This lamp is a consumable. It may burn out
or its brightness may decrease during use. In such
cases, replace the lamp with a new one as soon as
possible. Be sure to replace the lamp with a new lamp
separately sold that is exclusive to this projector.
Contact your dealer for purchase of the lamp.
Spare lamp VLT-XD8600LP
Warning:
• Becarefulnottodropthelampxingscrewsinto
the inside of the projector. Don’t put a metal piece
or flammable object into the projector. Using the
projector with any foreign object present inside
may result in electric shock or fire. When you can’t
remove the foreign object from the inside, contact
your dealer for removal.
• Donottouchthelampwithbarehandsorgive
a shock to the lamp. Attach the lamp properly.
Improper handling may cause explosion.
• Besuretoinstallthelampsecurely.Whenthelamp
isn’t installed properly, it won’t illuminate. Improper
installation may also result in fire.
• Don’tshaketheremovedlampordon’tliftitabove
your face. You may be injured in your eye by flying
or falling glass fragments.
• Don’treplacethelampimmediatelyafteruse
because the lamp cover is very hot. You may get
burned. Turn off the power using the POWER
button. After the lamp goes out, wait about 2
minutes until the intake and exhaust fans for
cooling the lamp stop rotating. Then unplug the
power cord, and wait at least 1 hour to allow the
lamp to cool down enough to the touch.
Interval of lamp replacement
The recommended interval of lamp replacement is
about 4000 hours
*1*2
of consecutive use. Such interval
differs depending on the operating environment
and may be shorter than 4000 hours
*1*2
. Decrease
in luminescence and/or color brightness indicates
that the lamp needs to be replaced. When the lamp
operation time exceeds 3000 hours
*1
, the indicator
will blink alternately between green and red (while the
lampislit;whenthelampisnotlit,theindicatorwill
be lit red only) and the lamp replacement message
will appear on the screen for 1 minute everytime the
lamp is turned on. When the lamp has been used
for about 3800 hours
*1
, the replacement message
(LAMP REPLACEMENT) will appear on the screen for
1 minute every 20 hours
*1
thereafter. When the lamp
operation time exceeds 4000 hours
*1*2
, the projector
automatically shuts off.
*1: Duration when LAMP MODE of the INSTALLATION 1
menu is set to LOW. When it is set to STANDARD, this
duration will be shorted.
*2: When LAMP MODE is set to STANDARD, this duration
will be shorted to 2000 hours.
Caution:
• Don’tremovethelampforanypurposeotherthan
replacement. Unnecessary removal of the lamp
may result in a breakdown.
• Thisprojectorusesahigh-pressuremercurylamp
as the light source. The high-pressure mercury
lamp may explode or fail to illuminate permanently
because of an impact, scratch, or deterioration
through use. The period of time until explosion or
permanent failure to illuminate varies considerably
from lamp to lamp, depending on operation
conditions. Therefore, the lamp may explode soon
after the start of use.
• Thepossibilityofexplosionofthelampincreasesif
you use it beyond its replacement period. When the
instruction of lamp replacement appears, replace it
with a new one immediately even if the lamp is still
lighting normally.
• Whenthehigh-pressuremercurylampexplodes,
glass fragments will scatter inside or outside the
lamp box and the gas charged inside the lamp
will diffuse inside or outside the projector. The gas
inside the lamp contains mercury. Be careful not
to breathe it or avoid it from entering your eye or
mouth. If you should breathe it or if it should enter
your eye or mouth, see a doctor immediately.
• Intheeventthatthehigh-pressuremercury
lamp exploded, glass fragments may have been
scattered inside the projector. Ask your dealer to
replace the lamp and to inspect the inside of the
projector. When you clean or replace the lamp by
yourself, be sure to hold the handle of the lamp.
You may get injured by glass fragments.
• Whenremovingthelampfromtheceiling-mounted
projector, use the lamp replacement tray packed
with the projector or option lamp to prevent glass
fragments from scattering.
• Besuretousethelampexclusivetothisprojector,
VLT-XD8600LP. Use of other lamps may cause a
failure of the projector.
Before replacing the lamp
1. Check which indicator (for LAMP 1 or LAMP 2) is
illuminating or blinking.
LAMP 2 indicator
LAMP 1 indicator
• Forthestatusesoftheindicatorsurgingyouto
replace the lamps, see page 73.
• Replacethelampindicatedbytheilluminating/
blinking indicator using the following procedure.
• Whenbothindicatorsareilluminatingorblinking,
replace both lamps at the same time.
To replace the lamp:
1. Unplug the power cord from the outlet or appliance
inlet.
2. Loosen two screws (a) that are securing the lamp
cover using a Phillips screwdriver and remove the
lamp cover (b) from the projector.
(a)
(b)
64

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mitsubishi XD8500U bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mitsubishi XD8500U in de taal/talen: Engels als bijlage per email.

De handleiding is 10,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Mitsubishi XD8500U

Mitsubishi XD8500U Aanvulling / aanpassing - English - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info