475255
78
Verklein
Vergroot
Pagina terug
1/110
Pagina verder
78 Appendices
For assistance call 1(800) 332-2119
Programming the Remote Control
1.
Press one of the upper buttons on the remote
control to change to the correct mode for the
product you want to control. Refer to the table
below. Only one of each device type can be con-
trolled in each mode.
Mode Affected Device
CAB/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
2.
Press and hold
POWER
on the remote control for
several seconds until the key flashes twice and
goes off.
3.
Release the
POWER
key.
4.
Enter the first five-digit code listed for your equip-
ment in the reference tables that follow.
If you need to start over or wish to exit
programming mode, temporarily change to a
different device mode.
5.
Point the remote control at the equipment and
press
POWER
. If the product has no power on/off
function, press a different key, such as (
PLAY
),
(
STOP
),
VOLUME UP
, or
MUTE.
• If the equipment responds, the remote control
is properly programmed.
• If the equipment does not respond, repeat
steps 4 and 5 with the next five-digit code
listed for your equipment.
6.
Once you have found the correct code, write it in
the space below for future reference.
Mode
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
IMPORTANT
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
To determine the code programmed for any mode:
1.
Set the mode to the one you wish to verify.
2.
Press and hold
POWER
on the remote control for
several seconds until the
key
flashes twice and goes
off.
3.
Press keys
9 9 0
4.
Press
1
and count the flashes of the power key.
Write down the number of flashes as the first digit
of the code.
5.
Repeat step 4 for the other digits of the code.
Press
2
to see flashes for the second digit, press
3
for the third digit,
4
for the fourth digit, and
5
for the
fifth digit.
Audio Lock: Universal A/V Receiver
Control
With Audio Lock enabled, the remote control oper-
ates volume and mute on an A/V receiver in all control
modes. Activate Audio Lock if you always use an A/V
receiver with your TV and other A/V equipment.
1.
Program
AUDIO
mode for your A/V receiver as
described in “Programming the Remote Control” on
this page.
2.
With the remote control in
AUDIO
mode, hold
POWER
on the remote control for several seconds until the
key flashes twice and goes off.
3.
Press keys
9 9 3 ENTER
The
POWER
key will flash twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
1.
Press and hold
POWER
for several seconds until it
flashes twice and goes off.
2.
Press keys
9 9 3 VOLUME UP
.
The
POWER
key will flash four times to indicate Audio
Lock has cleared.
Appendix A: Programming the Remote Control, continued
78

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mitsubishi WD-82838 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mitsubishi WD-82838 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info