587218
14
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
13
WHEN THE CHECK INDICATOR LIGHT (RED) FLASHES
INSPECTION DISPLAY, FILTER SIGN, AIR CONDITIONER NUMBER, STANDBY, ROOM TEMPERATURE AND BACK UP DISPLAY
< WIRED REMOTE CONTROL >
The air conditioner stops in the event
any trouble occurs.
At the same time, the check indicator
light flashes in red and the error code is
displayed in the ON timer display area and
the following is displayed in the display
area.
(Air conditioner number)
Ç
(lights for 2 seconds by turns)
Error code
Air conditioner No.
1
Press AIR CON No. button.
Enter AIR CON No. display mode.
2 Press button.
AIR CON No. and error codes are
displayed in order from the lowest.
Press button to display in the
reverse order.
3 Press button.
Return to the AIR CON of the lowest
number.
1 2
ERROR display when multiple indoor units are connected
If errors have occurred for all the connected air conditioning unit.
Initially, the error display shows the formation of the air
conditioning unit whose number is the lowest.
Errors of other air conditioning unit can be checked with the
following procedure.
1
Press AIR CON No. button.
AIR CON No. display mode appears.
2 Press button.
AIR CON No. are displayed in order
from the lowest. And error codes are
displayed on the unit in trouble.
Press button to display in the
reverse order.
3 Press button.
Return to the AIR CON of the lowest
number.
If errors have occurred for some of the connected AIR CON
units.
Only the units for which errors have occurred stop operating.
The remote control shows the operating units.
NOTICE
If button is pressed once while errors are displayed,
the errors display is turned off, and return to the stop mode.
If
button is pressed again, the errors are displayed.
HOW TO DISPLAY AIR CON NO.
By operating AIR CON No. button, the number of the connected AIR CON
unit and error codes of the units which have the record are displayed.
1
Press AIR CON No. button.
AIR CON No. display mode appears
and the AIR CON of the lowest number
is displayed. Other displays all turn off.
2 Press button.
AIR CON No. are displayed in order
from the lowest. And error codes are
displayed on the units which have
suffered from failure in the past.
Press button to display in the
reverse order.
3 Press button.
Return to the original display.
1 2
NOTICE
The AIR CON No. can be displayed without relation to its modes of
operation, stop, forcible stop due to an error.
Buttons other than “AIR CON No.” “” ““ON/OFF” cannot be
operated.
1 2
STANDBY DISPLAY
During the first operation after breaker power supply input or the
recovery from power failure, “
” can be displayed on
the remote control for max 30 minutes.
The refrigerant oil protection control is activated to protect the
compressor and this isn’t a failure. Please wait till the display turns
off.
WHEN THE FILTER CLEANING MESSAGE IS DISPLAYED
The “ ” is displayed
When the cumulative operation time
reaches set amount number of hours in
order to notify the time for cleaning.
Clean the air filter. See page 16
“FILTER CLEANING” is displayed in the
display area. It is displayed for one second
every five seconds while the unit is running.
It is always lit while the system stopped.
After cleaning
1 Press RESET button.
The cumulative operation hours is
reset and the “FILTER CLEANING”
message turns off.
1
ROOM TEMPERATURE DISPLAY
If room temperature display setting is activated, room temperature is
displayed on the remote control display. Then airflow display turns off,
but airflow adjusting button is operative. Consult your dealer for settings.
Ç
The room temperature display
WIRELESS REMOTE CONTROL
All displays are described in the liquid crystal display for explanation
OPERATION MODE display
Indicates selected operation with .
FAN SPEED button
Every time this button is pressed, the mode is switched
as below.
HI MED LO
ROOM
*
TEMP display
Indicates set temperature.
FILTER display
Indicates for two seconds when FILTER
button is pressed.
(AUTO) (COOL) (HEAT)
(FAN) (DRY)
ROOM
*
TEMP/TIME SETTING button
Sets room temperature by pressing or button.
Sets time when setting the time.
ACL switch
Used to reset the microcomputer.
FAN SPEED display
Indicates the selected airflow volume.
FILTER button
TIMER CANCEL button
Used to cancel the TIMER SETTINGS.
Transmitter
Sends signal to the air conditioner.
Used to reset (turn off) the filter sign.
Press the button only after completing the filter cleaning.
Operation section Display section
OPERATION MODE select button
(Dehumidifying
operation is prohibited for FDU-F.)
Every time this button is pressed, displays switch as below
ON/OFF button
When this is pressed once, the AIR CON starts to operate
and when this is pressed once again, it stops operating.
14
14
14
14
14
15
14
14
15
When you press each button of wireless remote
control, directing properly to the receiving part of
the air conditioner, the signal is transmitted. If the
air conditioner receives the signal correctly, the light
of operation indicator will flash.
ATTENTION
The operation of remote control must be performed
slowly and steadily.
HOW TO OPERATE
ABOUT REMOTE CONTROL HOLDER
The remote control can be mounted on the wall or
pillar with the remote control holder.
Slide from the upper part of the holder to place or
take out the remote control.
ATTENTION
Do not place the remote control to the following places.
The place exposed to direct sunlight or other strong
lighting.
The place exposed to high temperature, for
EXAMPLE, on the electric carpet or near a stove.
If the signal receiving part of the air conditioner is
exposed to direct sunlight or other strong lighting, it
may not receive the signal. In this case, shut out the
sunlight or turn down the lighting.
Do not place anything between the remote control and the unit.
Do not operate the remote control for other electric
appliances which can be operated with a remote control.
Handle it with utmost attention.
Remove the batteries when the remote control is
not used for a long time.
Even if the remote control is not found or damaged,
you can operate the air conditioner with itself. See
“How to use the backup button” on page 15.
NOTICE
If the display of remote control has troubles, press RESET switch.
WIRELESS REMOTE CONTROL HANDLING PROCEDURE
REPLACING THE BATTERIES
1 Pull out the cover.
2 Replace the old
batteries with
new ones.
(R03×2)
3 Close cover.
4 Adjust the current time.
See page 14
When any error occurs on the
display,
Press
ACL
switch with
a ballpoint
etc.
NOTICE
If the remote control is set as “Radio
Interference Prevention Setting”, it
returns to default when the batteries
are removed. It is necessary to perform
the next procedures again.
If the following occurs, the batteries are exhausted. Replace with new ones.
When the signal is transmitted, the AIR CON does not display reception.
The display fades away or does not show anything.
How to set Radio Interference
Prevention Setting
It is possible to sent two way. Press
ACL
switch with
AIR FLOW
button kept pressing or Insert the
batterles with
AIR FLOW
button
kept pressing.
ATTENTION
Do not use old and new batteries
mixed.
Remove the batteries when the
remote control is not used for a long
time.
The recommendable effective period
of a battery is about 6 to 12 months.
(It depends on the usage.)
When the batteries are inserted, each operation mode
is set as the right figure. Adjust the current time referring
to page 14. (The figure is for operation, and only the
current time is displayed for stopping)
Pay attention
to the and
marks
The recommendable effective
period is printed on the battery.
This may be shorter due to
manufacturing time of the unit.
However the battery may be still
working in order after expiry date.
NAMES AND FUNCTIONS OF REMOTE CONTROL BUTTON <WIRELESS REMOTE CONTROL>
BACK UP DISPLAY
If the back up display appears on the screen,. Please contact the
dealer where the unit was purchased.
The back up display is indicated per 1 second at intervals of 5
seconds when the air conditioners is in operation.
Automatic operation of the KX (except KXR) cannot be
selected. When automatic operation is selected in this unit,
set the remote controller to disabled the automatic operation.
While pressing the
MODE
button ant then press the
ACL
switch, or while pressing the
MODE
button and
then insert the batteries to the remote controller, then it
has been disabled the automatic operation.
ATTENTION
When the batteries are removed in the remote
controller once, the system is returned to initial
setting (automatic enable setting). In case that
removing the batteries in the remote controller,
perform the above operation once again.
SETTING CHANGE OF AUTOMATIC OPERATION
IN case of FDU-F
The setting temperature of the remote controller indicates the outdoor temperature
while operating thermostat ON/OFF.
IN case of FDU-F
The setting temperature of the remote controller indicates the
outdoor temperature while operating thermostat ON/OFF.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mitsubishi FDU-F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mitsubishi FDU-F in de taal/talen: Engels als bijlage per email.

De handleiding is 10,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Mitsubishi FDU-F

Mitsubishi FDU-F Gebruiksaanwijzing - Nederlands - 22 pagina's

Mitsubishi FDU-F Gebruiksaanwijzing - Deutsch - 22 pagina's

Mitsubishi FDU-F Gebruiksaanwijzing - Français - 22 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info