641640
7
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
7

Core bits are useful for drilling larger holes for
conduit and pipe. MILWAUKEE Thin Wall Core
Bits have heat-treated steel bodies with durable
carbide tips. These core bits are specially designed
for fast, accurate drilling with combined hammering
and rotary action.
1. Clean and lubricate the
threads on the adapter
and core bit to make later
removal easier. Screw the
threaded end of the adapter
into the rear of the core bit.
 For core bits 1- 1/4"
and larger, push the guide
plate onto the pointed end of
the center pin. Insert the center
pin and guide plate assembly
into the core bit. Be sure the
small end of the center pin is
securely placed into the hole
in the center of the core bit.
2. Insert the adapter into the nose
of the tool as described in “In-
stalling Bits”. Set the hammer/
drill shift knob to hammering
with rotation.
3. Press the center pin firmly
against your center mark, hold
the tool rmly and pull the trigger.
 If a center pin and guide
plate are not available, use a template or notched
board to start the hole.
5. After drilling to about the depth of the core bit
teeth, remove the center pin and guide plate from
the core bit. Resume drilling.
6. To change the core bit, hold the tool upwards,
pointing it away from your body, and run it briey
in forward to loosen the core bit from the adapter.
 To make holes deeper than 3", remove the
core bit, break and remove the core. Resume drilling.
Adapter
Core
Bit
Center
Pin
Guide
Plate
Clean
and
lubricate
threads



Always allow the motor to
come to a complete stop be-
fore using the control switch.
For  (clockwise) rota-
tion, push the control switch
to the left side of the tool.
Check the direction of rotation
before use.
For  (counterclock-
wise) rotation, push the con-
trol switch to the right side of
the tool. Check direction of
rotation before use.

1. To  the tool, grasp the handle rmly and pull
the trigger.
2. To  the speed, increase or decrease the
pressure on the trigger. The further the trigger
is pulled, the greater the speed.
3. To  the tool, release the trigger. Make sure
the tool comes to a complete stop before laying
the tool down.

The lock-on button holds the trigger in the ON posi-
tion for continuous full speed use.
1. To lock the trigger, hold in the lock button while
pulling the trigger. Release the trigger.
2. To unlock the trigger, pull the trigger and release.
The lock button will pop out.

Position the tool, grasp the handles rmly and pull
the trigger. Always hold the tool securely using
both handles to maintain control. This tool has
been designed to achieve top performance with
only moderate pressure. Let the tool do the work.
If the speed begins to drop off when drilling large
or deep holes, pull the bit partially out of the hole
while the tool is running to help clear dust. Do not
use water to settle the dust since it will clog the bit
utes and tend to make the bit bind in the hole. If
the bit should bind, a built-in, non-adjustable slip
clutch prevents the bit from turning. If this occurs,
stop the tool, free the bit and begin again.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Milwaukee 5262-20 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Milwaukee 5262-20 in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info