626792
8
Verklein
Vergroot
Pagina terug
1/168
Pagina verder
6millnorway.com
EN
Assembly
See figure 2 on separate illustration sheet
A. Drill holes in the wall for holes 1 & 2. Then drill holes in the wall for the topmost holes
(holes 3 & 4 by using 6).
B. Insert the wall plugs into the drilled holes and attach the bracket with 4 screws.
C. Place the heater on the lower lugs on the bracket, then hang the heater on the
upper lugs (lift the heater slightly to align the heater with for the upper lugs). Screw in
the locking screws on the top of the bracket (clockwise).
ATTENTION! HORIZONTAL PLACEMENT ONLY
Temperature calibration
See figure 3 on separate illustration sheet
It may occur deviation between the temperature registered by the heater and the actual
temperature in the room. This can be caused by several reasons, however, the most com-
mon is that the heater is placed in a fair distance from where you usually reside. When you
set the temperature to for example 22 degrees, it is only natural that you expect the same
temperature where your sofa is placed for instance. However, the temperature sensor is
placed on the product itself, and therefore a deviation in temperature may occur. To adjust
this, all Mill heaters are equipped with a calibration function, which enables you to adjust
the temperature registered by the heater. N.B! The room must have achieved a stable
temperature before any calibration.
Press 2 times and use + or - to set the actual temperature observed in the room. Con-
firm withor wait 15 seconds for automatic confirmation.
Resetting the heater
See figure 4 on separate illustration sheet
Turn off the heater‘s main switch. Press and hold (9 while you turn on the heater‘s main
switch.
Memory function
The heater remembers all the temperature settings and will automatically return to the
desired temperature after a power cut. Your day- and nighttime setbacks will however be
deleted after a power cut, and you will need to register the programs again.
Open window” function
The heater has an “open window” function that is activated instantly when it registers a
sudden drop in temperature with more than 2 degrees Celsius in 2 minutes. The heater will
automatically stop heating and FO will be visible in the display of the heater.
The heater will automatically start heating again after 10 minutes (the display switch from
FO to desired room temperature).
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mill MB1000L DN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mill MB1000L DN in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 1.58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Mill MB1000L DN

Mill MB1000L DN Gebruiksaanwijzing en installatiehandleiding - Nederlands - 15 pagina's

Mill MB1000L DN Gebruiksaanwijzing en installatiehandleiding - Deutsch - 17 pagina's

Mill MB1000L DN Aanvulling / aanpassing - English - 2 pagina's

Mill MB1000L DN Gebruiksaanwijzing en installatiehandleiding - English - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info