579697
3
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
User Guide
User Guide
GEOPOINT LCD
PERSONAL TRACKER
GEOPOINT LCD
PERSONAL TRACKER
User Guide
July Edition 2009
Limitation of Liability
The Manufacturer reserves the right to modify the devices or the device specifi cations in this manual without prior notice. Any copy of this manual,
in part or in full, whether by photocopy or by other means, even of electronic nature, without the manufacture giving written authorisation, breaches
the terms of copyright and is liable to prosecution.
It is absolutely forbidden to use the device for different uses other than those for which it has been devised for, as inferred to in this manual. When
using the features in this device, obey all laws and respect privacy and legitimate rights of others.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL THE MANUFACTURER BE LIABLE FOR
CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH SAID PRODUCT AND THE MANUFACTURER NEITHER ASSUMES NOR
AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OBLIGATION OR LIABILITY OTHER THAN SUCH AS IS
EXPRESSLY SET FORTH HEREIN.
All trademarks in this manual are property of their respective owners.
The information contained in this manual is for information purposes only, is subject to changes without previous notice and cannot be considered
binding for the Manufacturer. The Manufacturer assumes no responsibility for any errors or incoherence possibly contained in this manual.
Printed in Italy.
Note for the users of appliances
According to the article 13 of the Legislative Decree no. 151 dated July 25, 2005, “Enforcement of the 2002/95/EC and
2003/108/EC directives, relavant to the reduction of dangerous substances in electric and electronic applinaces, as well
as waste disposal”, the symbol of a crossed dustbin applied on appliances or on their cases means that the product at
the end of its life cycle must be disposed in a dedicated location than other waste.
The user must, therefore, dispose the aplliance at its end-of-life in the relevant disposal site for electric and electronic waste or
give it back to resellers at the time of purchasing a news equivalent one.
The correct disposal and consequant start up of a recycling of the unused appliance, treatment and fi nal disposal compatible
to the enviroment concurs to avoid possible negative effects on the enviroment and health and favours the reusing and / or
recycling of the parts making the apparatus.
The abusive disposal of such products done by users is fi ned according to the present legislation.
Contents
Safety Instructions ................................................................................................................................... 5
General Information ................................................................................................................................. 6
Preliminary Procedures .......................................................................................................................... 8
Inserting the SIM Card .................................................................................................................... 8
How to Charge the Battery ............................................................................................................. 9
Use of the Tracker ..................................................................................................................................10
Symbols ............................................................................................................................................ 10
Keypad Lock ....................................................................................................................................12
Menu Structure ................................................................................................................................13
GPS .................................................................................................................................................... 14
Phone ................................................................................................................................................. 14
Anchor ............................................................................................................................................... 16
Finder ................................................................................................................................................. 18
Guide ................................................................................................................................................. 19
Speed ................................................................................................................................................ 21
Setup ..................................................................................................................................................22
SOS Key ............................................................................................................................................ 28
Tracker Management by SMS ............................................................................................................ 30
Position Request ............................................................................................................................. 30
Automatic Position Sending ......................................................................................................... 30
Anchor ............................................................................................................................................... 31
Geofence .......................................................................................................................................... 32
Alarm SMS ........................................................................................................................................ 33
Reading and Writing SMS Commands......................................................................................35
Setup by MyTrack Software ................................................................................................................ 42
Power Save Mode...........................................................................................................................42
Alarm SMS ........................................................................................................................................ 45
Position Data Recording ...............................................................................................................46
Update of the Tracker Firmware Version................................................................................... 47
Maintenance ............................................................................................................................................ 48
Technical Features .................................................................................................................................49
Manufacturer’s Limited Warranty ...................................................................................................... 50
Warranty Period ...............................................................................................................................50
Safety Instructions
5
Safety Instructions
Please read the following safety instructions carefully. Not following them may be dangerous and/or illegal. For
further details, please read carefully the user manual complete version contained in the enclosed CD ROM.
Do not switch the device on when prohibited or whenever it could cause any interference or danger.
Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your fi rst
consideration while driving should be road safety.
All wireless devices may be susceptible to interference, which could affect the performance of other
appliances (TV, radio,...).
Switch the device off in hospitals or near medical equipment (hearing aid equipment, pacemaker, ...) the
device could cause interference. Always keep a distance of 20 cm between pacemaker and device.
Wireless and digital devices can cause interference with aircraft equipment.
Do not use the device at a refuelling point. Switch-off when near petrol stations or fuel depots and chemical
plants. The device could interfere with the correct functioning of the electronic equipment.
Do not use the device where blasting is in progress.
Do not use the device for any uses other than those it has been built for. Keep to the instructions as
explained in the product manual.
Only qualifi ed personnel may install or repair this product.
Use only approved accessories and batteries. Do not use incompatible products. The use of nonstandard
products can cause damage to device and/or people.
The batteries must be disposed according to the appropriate modes. The consumer must duly hand in
worn out batteries, either at the appropriate collection points for the general public, in his own town, or
wherever batteries of the same kind are sold (compulsory warning according to law on the disposal of
batteries).
The device is not water-resistant, keep it dry. Contact with water or any other liquid could cause serious
damage to the device.
6
General Information
General Information
The tracker is a portable device able to transmit its geographical location to a mobile phone or PC in real-time.
Moreover, the detected data can be recorded for further analysis.
The tracker is available in two different version:
LCD : GPS tracker with display, phone and 2MB data memory.
BOX : GPS tracker without display, without vocal communication and 512kB data memory.
Both trackers can be offered combined in the KIT version, particularly indicated for the use of Finder function,
useful for real-time locating.
This User Guide describes the tracker in the LCD version.
The tracker has three basic functions:
locating and transmitting its actual position
sending an SOS message in case of an emergency
voice communication as a mobile phone
The tracker is provided with MyTrack software allowing the tracker management and personal tracking.
The GPS receiver and the GSM device work at higher radio frequencies which can be stopped
by enclosures containing metal and plastic parts.
It is suggested to keep the tracker under light clothes, as external as possible.
Examples of shielding materials: kevlar, carbon fi bre, some polyurethanic and polyamidic resins
especially if black, etc.
Examples of materials which cannot infl uence the radio waves: ABS, ABS+PC, policarbonate,
etc.
For further details on tracker use and functions, please read carefully the user
manual complete version contained in the enclosed CD ROM.
7
General Information
SCROLL
FUNCTION
UP (+)
DOWN (-)
SOS KEY
USB
DC IN
BUZZER
ON/OFF
MULTIFUNCTION KEYS
JOG
DISPLAY
LOUDSPEAKER
MICROPHONE
HEADSET
PUSH
FUNCTION
ENTER
8
Preliminary Procedures
Preliminary Procedures
Inserting the SIM Card
In case of a SIM card:
prepaid : the communication between the tracker and the provided software is made exclusively by SMS
text or GPRS network.
with subscription : the communication between the tracker and the provided software is made by
SMS text, GPRS network or also sending/receiving data (only if the data number has been activated by
the network provider).
PIN: - - - - - Before inserting the SIM card in the tracker, disable the PIN code by means
of a mobile phone.
Inserting a SIM card any SMS message, contained in it or which will be
received in the future, will be deleted and cannot be retriveable.
30 sec.
If the battery is not inserted within 30 seconds, the date and hour settings
will be ERASED.
To insert the SIM card, remove the back cover and lifting out the battery.
9
Preliminary Procedures
How to Charge the Battery
Before using the tracker for the fi rst time, the battery must be completely charged.
Before charging, check that the network electrical supply corresponds to that of the battery charger. Do not
exceed the network voltage indicated on the battery charger.
Use only batteries and battery chargers with the following features:
Battery: model ABL-6C Li-ion
Battery charger: model ZD050050EU
Car charger: model ESC-004
The manufacturing company is not liable for any damage to the tracker
due to the use of accessories different from those expressly indicated.
Do not leave the tracker in particularly hot or cold environments during the
battery charging. Keep the tracker between -10°C and +40°C environmental
temperature.
When the battery is almost discharged, the tracker, if ON, emits an acoustic
warning every minute.
10
Safety InstructionsUse of the Tracker
10
Use of the Tracker
Symbols
GSM network coverage
Battery status:
Charged battery
Discharged battery
GPS signal coverage:
Maximum level
.... FIX procedure
More symbols can be displayed:
Data connection
GPRS connection
SMS sending/receiving
Connected headphones
Connection via USB
Activated keypad lock
Time
(hh:mm)
The item relevant to the key changes
according to the function in use
The info message changes
according to the function in use
UNLOCK?
Yes 10:30 No
Safety Instructions
11
Use of the Tracker
11
Tracker Function Description Refer to
GPS Info on Display
the tracker displays the info relevant to its
position
chapter Use of the Tracker
Phone
the tracker displays the phonebook and a
call can be received or carried out
chapter Use of the Tracker
SOS key
the tracker sends an alarm message chapter Use of the Tracker
Position Request
the tracker sends an SMS containing
its position to the phone number which
requested this data
chapter Tracker Management by SMS
Automatic Position Sending
the tracker sends automatically its position
by SMS or by GPRS connection
chapter Use of the Tracker, section Setup
chapter Tracker Management by SMS
Position Data Recording
the tracker records its position data to
review the track afterwords
chapter Use of the Tracker, section Setup
chapter Setup by MyTrack Software
Geofence
the tracker sends an alarm SMS to the
preset phone number everytime it exits or
ri-enters in a preset rectangular area
chapter Tracker Management by SMS
Anchor
the tracker sends an alarm SMS to the
preset phone number everytime it exits or
ri-enters in a preset circular area
chapter Use of the Tracker
chapter Tracker Management by SMS
Finder
the tracker fi nds another tracker of the
same type and displays the direction and
the distance to follow
chapter Use of the Tracker
Guide
the tracker fi nds a previously saved
destination point and displays the direction
and the distance to follow
chapter Use of the Tracker
Speed
the tracker emits an acoustic alarm when
the preset speed limit has been overcome
chapter Use of the Tracker
12
Safety InstructionsUse of the Tracker
12
Tracker Function Description Refer to
Power Save Mode
the tracker switches on/off automatically to
optimize the battery consumption
chapter Setup by MyTrack Software
Alarm SMS
the tracker sends alarm SMS to the preset
phone number everytime a status change
happens (low battery, memory full, ...)
chapter Tracker Management by SMS
chapter Setup by MyTrack Software
The tracker can work without the SIM card. In this case, all functions operating
with GSM/GPRS network will not be available.
Keypad Lock
The keypad lock disables the keys to avoid accidental use of the tracker.
SOS It is possible to send an alarm message by means of pressing the SOS key, even when the
keypad lock is activated.
LOCKED
10:30
UNLOCK?
Yes 10:30 No
3 sec.
Network Provider
10:30 Menu
3 sec.
Safety Instructions
13
Use of the Tracker
13
Menu Structure
To access the main menu, press Menu in the Home page. The fi rst section, GPS, will be displayed. Scroll
down the sections turning the JOG and press OK to enter into the desired item. To exit the main menu and
display the Home page, press Home.
The Speed function is not available in case of tracker compatible for OnTrack
application.
W
GUIDE
Home 10:30 OK
ANCHOR
Home 10:30 OK
PHONE
Home 10:30 OK
GPS
Home 10:30 OK
FINDER
Home 10:30 OK
SETUP
Home 10:30 OK
SPEED
Home 10:30 OK
14
Safety InstructionsUse of the Tracker
14
GPS
The data received by the GPS system are shown on the display.
Lat: 45°45.67N
Long: 08°12.34E
Alt: 256 m
Back 10:30
Spd: 20km/h
Dir: 270°
Sat: 8-3D FIX
Back 10:30
GPS
Home 10:30 OK
Phone
The tracker also works as a GSM telephone. The call functions are extremely simple. The phone numbers and
names are pre-programmed in the phone book by means of the provided software.
Safety Instructions
15
Use of the Tracker
15
PHONE BOOK (MAX 10 NUMBERS)
John
+123456789
Back Call
Mary
+123456789
Back Call
PHONE
Home 10:30 OK
RECEIVING A CALL
VOL:
       
Back
Incoming Call...
+123456789
Reject Answer
00:05
+123456789
Hungup
During the transfer of data between the tracker and PC, it is not possible to
make or receive any calls.
SIM
The tracker does not allow to use the phone book possibly memorized on the
SIM card in use. However, the information contained in it, except for SMS
messages saved by a mobile phone, will not be erased.
16
Safety InstructionsUse of the Tracker
16
Anchor
The Anchor function allows to monitor within a pre-established circular area the position of a person, an object
or an animal. When the tracker detects the exiting from the pre-established area or the ri-entering, it sends
an alarm SMS containing its position data to the preset phone number. This function is programmable either
operating directly on the tracker or by the provided software or by sending an SMS command.
Anchor Enabled
Dist: 45 m
Limit: 50 m
OFF
Back 10:30 OK
Anchor Disabled
Dist:
Limit: 50 m
Change
Back 10:30 OK
Anchor Disabled
Dist:
Limit: 100 m
Change
Torna 10:30 OK
Back OK
Set Limit:
0 m
ANCHOR
Home 10:30 OK
Back OK
Set Limit:
50 m
Available values: 50, 100, 200, 300, 500, 700, 1000, 1500, 2000, 3000, 4000 meters
Max 50m
Area centre to be monitored
Set Center:
Lat: 45°45.67N
Long: 08°12.34E
Back Center
Anchor Enabled
Dist: 45 m
Limit: 50 m
Change
Back 10:30 OK
Safety Instructions
17
Use of the Tracker
17
Before enabling this function, it is necessary to set the phone number where
SMS will be sent by means of the provided software.
Example of the SMS message displayed on the mobile phone, when the tracker enters the area
GEO,ID:GLORIA,ANCHOR ENTER,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the tracker exits the area
GEO,ID:GLORIA,ANCHOR EXIT,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
The SMS message structure of the Anchor function is described here below:
GEO Tracker type.
ID:−−−−−− Tracker name preset by the user through the provided software.
ANCHOR ENTER Alarm message.
POS:−−−−−.−−−−−,−−−−−.−−−−− Latitude and longitude of the geographical position.
ALT:−−−−.− Altitude in m.
−−/−−/−−,−−:−− Event date and time (yy/mm/dd hh:mm).
18
Safety InstructionsUse of the Tracker
18
Finder
The Finder mode allows to fi nd another tracker of the same type (LCD or BOX version) by displaying the
distance and the direction to follow. The Finder function can only be used if the distance between the trackers
is less than 999 Km.
To carry out the Finder function, set the communication rate by the provided
software.
The necessary motion for updating the relevant position, must be no less than 10
meters in 3km/h. More motion means more precise indication of direction. It is important to
keep the tracker pointing in the direction used for reference. In every way, if change of direction
is inevitable, e.g. the ground is not viable, on approaching the correspondent, the direction will
be constantly updated and corrected by the tracker.
350
m
Back Detail
Mary
+123456789
Back 10:30 OK
No Connection...
Retry?
Yes 10:30 No
No Phone
Numbers in the
PHONE Book!
Back
FINDER
Home 10:30 OK
PHONE BOOK
Absence of GSM or GPS signal / Selected
voice not corresponding to a tracker
Dest: Mary
Lat: 45
°
12.34N
Long: 08
°
12.34E
Dist: 350 m
Back 10:30
350
m
Torna
Safety Instructions
19
Use of the Tracker
19
Guide
The Guide function allows to reach a destination point by displaying the distance and direction. The Guide
function is available only if the distance between the tracker and destination point is less than 999 Km.
It is possible to set the Guide function by means of the provided software or directly on the tracker.
3D FIX It is suggested to save the destination point when the GPS signal level
is optimal. In case of weak GPS signal, the accuracy of destination point
coordinates will not be guaranteed.
HOW TO SAVE A DESTINATION POINT (MAX 30 POINTS)
Save As
Dest: Point 01
Lat: 45
°
12.34N
Long: 08
°
12.34E
Yes 10:30 No
01
02 ---
03 ---
04 ---
Back OK
---
Overwrite Data?
Yes 10:30 No
GUIDE
Home 10:30 OK
3 sec.
01
02 ---
03 ---
04 ---
Back OK
Point 01
3 sec.
20
Safety InstructionsUse of the Tracker
20
HOW TO REACH A DESTINATION POINT
The necessary motion for updating the relevant position, must be no less than 10
meters in 3km/h. More motion means more precise indication of direction. It is important to
keep the tracker pointing in the direction used for reference. In every way, if change of direction
is inevitable, e.g. the ground is not viable, on approaching the correspondent, the direction will
be constantly updated and corrected by the tracker.
350
m
Back Detail
Dest: HOME
Lat: 45
°
12.34N
Long: 08
°
12.34E
Dist: 350 m
Back 10:30
GUIDE
Home 10:30 OK
01 CASA
02 ---
03 ---
04 ---
Back OK
HOME
No GPS
Signal
Selected point not set
NO POINT
350
m
Torna
Safety Instructions
21
Use of the Tracker
21
Speed
The Speed function allows to set a speed limit which, when exceeded, causes the emission of a progressive
acoustic alarm: more is the difference between the real speed and that programmed, quicklier will be the
alarm reproduction.
The Speed function is not available in case of tracker compatible for OnTrack
application.
101km/h
100
Back 10:30 OFF
100km/h
Back 10:30 ON
SPEED
Home 10:30 OK
(ON) ENABLE
(OFF) DISABLE
22
Safety InstructionsUse of the Tracker
22
Setup
HOW TO ENABLE THE CYCLIC POSITION SMS SENDING
For further details on this function, refer to the chapter Tracker Management by SMS, paragraph Automatic
Position Sending.
Tracking
GPRS rate OFF
Back 10:30 OK
OFF
Tracking
GPRS rate OFF
Back 10:30 OK
OFF
SETUP
Home 10:30 OK
Main
Tones
Memory
Back 10:30 OK
Tracking
GPRS rate OFF
Back 10:30 OK
ON
Tracking
GPRS rate OFF
Back 10:30 OK
ON
Safety Instructions
23
Use of the Tracker
23
HOW TO SELECT THE RATE FOR CYCLIC GPRS CONNECTION
Available values: OFF, 1m, 5m, 10m,
15m, 30m, 1h, 2h, 4h, 8h, 12h, 18h, 24h.
Tracking
GPRS rate OFF
Back 10:30 OK
OFF
SETUP
Home 10:30 OK
Main
Tones
Memory
Back 10:30 OK
Tracking
GPRS rate
Back 10:30 OK
OFF
OFF
Tracking
GPRS rate
10:30 OK
OFF
OFF
Tracking
GPRS rate
10:30 OK
OFF
1m
Tracking
GPRS rate
Back 10:30 OK
OFF
1m
Before rate selection, check if the GPRS parameters have been set properly.
24
Safety InstructionsUse of the Tracker
24
TONES SETUP
Main
Tones
Memory
Back 10:30 OK
SETUP
Home 10:30 OK
Main
Tones
Memory
Back 10:30 OK
Ring
Call HIGH
Keys OFF
SOS ON
Back 10:30 OK
1
Ring
Call HIGH
Keys OFF
SOS ON
Back 10:30 OK
1
Ring
Call HIGH
Keys OFF
SOS ON
Back 10:30 OK
2
Ring
Call HIGH
Keys OFF
SOS ON
Back 10:30 OK
2
Ring
Call
Keys OFF
SOS ON
Back 10:30 OK
2
HIGH
Safety Instructions
25
Use of the Tracker
25
Ring Select the call tone type.
Call Set the call tone volume.
OFF: tone disabled. In case of a call, the tracker will not emit any acoustic signal.
LOW: tone with a low volume level.
HIGH: tone with a high volume level.
Keys Enable/disable the keys tone.
SOS Enable/disable the acoustic signal tone for the SOS key.
RECORDINGS
The tracker allows to record:
the detected events automatically without setting the recording
the position data to review the track afterwords, if the recording was previously set
The tracker can records approx. 70,000 position points and approx. 1,900 events.
When an event occurs, the tracker detects it and start to record in the Event LOG.
The following list shows all the events which can be detected and recorded automatically by the tracker.
power on/off
low battery
making or receiving a voice call
receiving a data call
making a GPRS call
hanging up a call
motion on/off
GSM network available/unavailable
GPS signal available/unavailable
entry/exit from Geofence area
entry/exit from Anchor area
rmware update
SOS alarm
memory erasing
roaming on/off
network GSM provider changing if roaming on
26
Safety InstructionsUse of the Tracker
26
Rate
Distance 0
Mode OFF
Erase
Back 10:30 OK
0
Main
Tones
Memory
Back 10:30 OK
SETUP
Home 10:30 OK
Main
Tones
Memory
Back 10:30 OK
Rate
Distance 0
Mode OFF
Erase
10:30 OK
0
Rate
Distance 0
Mode OFF
Erase
10:30 OK
1
Rate
Distance 0
Mode OFF
Erase
Back 10:30 OK
1
Rate
Distance
Mode OFF
Erase
Back 10:30 OK
1
0
Safety Instructions
27
Use of the Tracker
27
The setup of the position points recording can be carried out by means of the provided software or directly
on the tracker.
Rate Set the temporal recording rate. Available values: 0, 1, 5, 10, 30, 60, 300 seconds. By
selecting 0, the recording at temporal rate is disabled.
Distance Set the distance (in meters) to cover. Available values: 0, 10, 50, 100, 500, 1km. By selecting
0, the recording for covered distance is disabled.
Mode Select the memory recording mode.
FILL: after having fi nished all the available memory space, stop recording (the oldest
data is kept).
RING: after having fi nished all memory space, the data already recorded is overwritten
(the latest data is kept).
OFF: disable the recording.
Erase Delete all data contained in the memory.
The Erase function deletes all GPS data contained in the tracker memory. Once deleted, the
data is no longer retrievable.
If the Power Save Mode with position SMS or cyclic GPRS has been enabled, the
tracker position will be recorded at each automatic switching ON. The set Rate and Distance
parameters will not be considered.
28
Safety InstructionsUse of the Tracker
28
SOS Key
By pressing the SOS key for at least 2 seconds, for 5 consecutive times every minute, an SMS message is
immediately sent to the preset phone numbers (max. of 4 phone numbers), and a brief acoustic warning signal is
emitted at SMS sending (refer to the paragraph Setup). This message also contains the current data on the location,
if the GPS signal has been revealed. If there is no GPS signal coverage, the last position data will be sent.
SOS
SMS error!
SOS not sent!
Back
SOS No or SMS
center missing!
SOS not sent!
Back
GSM Signal
missing
SMS not sent!
Back Cancel
If there is no GSM signal If there is no SOS number or
no SMS center number set
If the previously set SMS
center number is not correct
SOS Sending
Back Cancel
If SOS tone is enabled
SOS Sent!
Pressed for at least 2 sec.
disable the SOS sending
Back to previous page without
disable the SOS sending
If SOS is sent
Safety Instructions
29
Use of the Tracker
29
If no numbers have been set or in the absence of GSM signal, every time the
SOS key is pressed, an acoustic warning signal is emitted.
GSM
In the event that there is no network service coverage, the alarm functions
may not be available.
Example of the SMS message displayed on the mobile phone, with the detected current position data
GEO,ID:GLORIA,SOS ALARM,POS:45g37.9480N,008g28.9992E,ALT:0218m,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, with the last position data detected
before the GPS signal loss
GEO,ID:GLORIA,SOS ALARM,LAST POS:45g37.9480N,008g28.9992E,ALT:0218m,07/04/10,10:09
The SMS message structure of the SOS function is described here below:
GEO Tracker type.
ID:−−−−−− Tracker name preset by the user through the provided software.
SOS ALARM Alarm message.
POS:−−−−−.−−−−−,−−−−−.−−−−− Latitude and longitude of the geographical position.
ALT:−−−−.− Altitude in m.
−−/−−/−−,−−:−− Event date and time (yy/mm/dd hh:mm).
30
Safety InstructionsTracker Management by SMS
30
Tracker Management by SMS
Position Request
It is possible to ask for the tracker position by means of an SMS command. After receiving the SMS command,
the tracker sends a message containing the position data to the phone number which sent the command.
To know the tracker position in real time, send the following command:
rpos
For further details, refer to the paragraph Reading and Writing SMS Commands.
Automatic Position Sending
The tracker can send its own position at a programmable rate. The automatic position sending can be carried
out in two different modes:
by SMS
by GPRS connection
CYCLIC POSITION SMS
The tracker can send an SMS message at intervals, containing all the information on its current position. This
function is useful for monitoring the tracker motion at a distance by a mobile phone.
To use this function, it is necessary to:
set, using the provided software, the phone number where the position messages will be sent
set the rate for cyclic position SMS using the provided software or sending an SMS command
enable the function using the provided software or sending an SMS command
Safety Instructions
31
Tracker Management by SMS
31
CYCLIC GPRS CONNECTION
The cyclic GPRS connection allows to connect the tracker automatically at a programmed rate for the
continuous position updating. At the programmed rate, the tracker will be connected only for the time needed
for sending the position point. This function is very useful if combined with the I-Scout web server as it allows
to display the detected positions by every station connected to internet.
To use this function, it is necessary to:
set the GPRS parameters using the provided software or sending an SMS command
enable the function setting the rate for the cyclic GPRS connection using the provided software
Anchor
The Anchor function allows to monitor within a pre-established circular area the position of a person, an object
or an animal. When the tracker detects the exiting from the pre-established area or the ri-entering, it sends an
alarm SMS containing its position data to the preset phone number.
This function is programmable using the complete SMS command (enabling and radius setting), either
operating directly on the tracker, or partially by the provided software.
When the complete SMS command is received by the tracker (e.g. wanc=1,0500), the function is enabled and
the current tracker position is considered as area central point. If the function is enabled without setting the
radius, the previously set coordinates for the central point and the last programmed radius will be considered.
If no radius was previously programmed, by default it will be set to 100 m.
This function is programmable completely by SMS command (wanc), either operating directly on the tracker.
By the provided software, only function enabling and radius setting is possible.
Before enabling this function, it is necessary to set the phone number where
SMS will be sent by means of the provided software.
32
Safety InstructionsTracker Management by SMS
32
Example of the SMS message displayed on the mobile phone, when the tracker enters the area
GEO,ID:GLORIA,ANCHOR ENTER,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the tracker exits the area
GEO,ID:GLORIA,ANCHOR EXIT,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
The SMS message structure of the Anchor function is described here below:
GEO Tracker type.
ID:−−−−−− Tracker name preset by the user through the provided software.
ANCHOR ENTER Alarm message.
POS:−−−−−.−−−−−,−−−−−.−−−−− Latitude and longitude of the geographical position.
ALT:−−−−.− Altitude in m.
−−/−−/−−,−−:−− Event date and time (yy/mm/dd hh:mm).
Geofence
The Geofence function allows to monitor the entry and the exit of the tracker in a pre-established area.
This is a rectangular area and can be programmed by set the area diagonal coordinates by means of the
provided software, or by means of an SMS command sent by a mobile phone.
To set the SMS command, refer to the paragraph Reading and Writing SMS Commands.
After having set the parameters of the Geofence function, the tracker will send an SMS message of alarm to
the preset phone number (set by means of the provided software) each time it enters/exits the pre-established
area or each time it is switched on outside the pre-established area.
Safety Instructions
33
Tracker Management by SMS
33
Example of SMS message displayed on the mobile phone, when the tracker enters the area
GEO,ID:GLORIA,GEOFENCE ENTER,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the tracker exits the area
GEO,ID:GLORIA,GEOFENCE EXIT,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
The SMS message structure of the Geofence function is described here below:
GEO Tracker type.
ID:−−−−−− Tracker name preset by the user through the provided software.
GEOFENCE ENTER Alarm message.
POS:−−−−−.−−−−−,−−−−−.−−−−− Latitude and longitude of the geographical position.
ALT:−−−−− Altitude in m.
−−/−−/−− −−:−− Event date and time (yy/mm/dd hh:mm).
Alarm SMS
The Alarm SMS are alarm messages sent (if the function has been enabled by the provided software) to a
phone number every time that:
the tracker battery is almost discharged
the tracker memory is full
the GPRS network is available
the GPRS network is not available
the GPS signal of the tracker has been lost
the GPS signal of the tracker has been restored
tracker motion is revealed
the tracker motion stops
34
Safety InstructionsTracker Management by SMS
34
This function can only be programmed by means of the provided software.
Example of the SMS message displayed on the mobile phone, when the tracker battery is almost discharged
GEO,ID:GLORIA,LOW BATTERY,07/04/10,10:09
Example of the SMS message displayed on the mobile phone,when the tracker memory is full
GEO,ID:GLORIA,MEMORY FULL,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the GPRS network is available
GEO,ID:GLORIA,GPRS OK,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the GPRS network is not available
GEO,ID:GLORIA,GPRS OFF,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when there is GPS signal
GEO,ID:GLORIA,GPS FIX OK,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the GPS signal has been lost
GEO,ID:GLORIA,NO GPS FIX,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when a tracker motion is revealed
GEO,ID:GLORIA,MOTION ON,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when tracker motion stops
GEO,ID:GLORIA,MOTION OFF,07/04/10,10:09
Safety Instructions
35
Tracker Management by SMS
35
The SMS message structure of the Alarm SMS function is described here below:
GEO Tracker type.
ID:−−−−−− Tracker name preset by the user through the provided software.
LOW BATTERY Alarm message.
−−/−−/−− −−:−− Event date and time (yy/mm/dd hh:mm).
Reading and Writing SMS Commands
The SMS commands allows to set or read some tracker settings. These messages can be sent by a mobile
phone or by a GSM device able to send/receive SMS (i.e. a GSM modem).
When the tracker is switched ON and there is GSM signal, it can receive any SMS command. If the tracker
receives a correct SMS command, an answer is sent to the SMS command sender.
If the message contains invalid characters, the tracker will not reply. If it contains invalid values, the tracker
will reply a message containing “COMMAND ERROR“. All commands start with the letter “r” (reading) or
w” (writing).
Ensure that the SMS commands are written exactly as shown in the table. Any
change (space, capital letter, small letter,...) could affect the recognition of
the command.
Before enabling the sending of position SMS in cyclic mode (wposc), ensure
that the SMS phone number has been programmed.
36
Safety InstructionsTracker Management by SMS
36
Reading Commands
Command
Meaning and Values Example
rpos Read instantaneous GPS position data.
The tracker can reply in 3 different ways:
A) POS: <position data> = GPS position in real
time.
B) LAST POS: <position data> = no GPS signal. The
reply message contains the last detected GPS data.
C) POS: NO GPS DATA = from the tracker switching
on, the GPS signal has not been detected.
NOTE: the date and time refer to:
SMS sending, in case of Reply A
last detected GPS data, in case of Reply B
Command: rpos
Reply A:
POS:41g37.8283N,012g28.8191E,
ALT:0262m,DIR:023g,SPEED:0050km/h,
SAT:09,07/05/26,15:56
Reply B:
LAST POS:45g37.8283N,
008g28.8191E,ALT:0262m,
DIR:023g,SPEED:0050km/h,
SAT:09,07/05/26,15:56
Reply C:
POS: NO GPS DATA
Description:
41g37.8283N Lat. in degree, min.
012g28.8191E Long. in degree, min.
0262m Altitude in m
023g Direction in degree
0050km/h Speed in km/h
09 Satellites number
07/05/26 Date (yymmdd)
15:56 Time (hhmm)
rposc Read cyclic position SMS setup and power save
mode status.
[status: 0=disabled, 1=enabled]
[rate: 01÷99 minutes]
[power save mode: 0=disabled, 1=enabled]
Command: rposc
Reply: rposc=1,01,0
Description:
1=enabled cyclic position SMS
01=1 minute rate
0=disabled power save mode
Safety Instructions
37
Tracker Management by SMS
37
Command
Meaning and Values Example
rms Read the accelerometer setup values.
[sensitivity: 00=disabled sensor, 01=maximum,
10=minimum]
[timeout: 01÷99 minutes]
Command: rms
Reply: rms=02,10
Description:
02=sensitivity level 2
10=10 minutes timeout
rgf Read the Geofence setup.
[status: 0=disabled, 1=enabled]
[LAT1,LONG1,LAT2,LONG2=latitude and
longitude of the 2 points which defi ne the Geofence
area]
Command: rgf
Reply:
rgf=1,45g37.7981N,008g28.8012E,
41g37.8971N,012g28.8012E
Description:
1=enabled
45g37.7981N,008g28.8012E=latitude
and longitude of the fi rst point
41g37.8971N,012g28.8012E=latitude
and longitude of the second point
ranc Read the Anchor setup.
[status: 0=disabled, 1=enabled]
[radius: 0050, 0100, 0200, 0300, 0500, 0700, 1000,
1500, 2000, 3000, 4000 m]
Command: ranc
Reply: ranc=1,0100
Description:
1=enabled
0100=radius at 100 m
38
Safety InstructionsTracker Management by SMS
38
Writing Commands
Command
Meaning and Values Example
wposc Set the cyclic position SMS in text format and the
relevant power save mode.
[enabling: 0=disable, 1=enable]
[rate: 01÷99 minutes]
[power save mode: 0=disable, 1=enable]
NOTE: the power save mode works only with
SMS rate5 minutes.
Never set like this: wposc=0,xx,1
NOTE: to enable or disable only the cyclic position
SMS, send the wposc command with the fi rst
eld only. In this case, the previously set rate is
considered.
Case A
Command: wposc=1,01,0
Reply: wposc=1,01,0 OK
Description:
1=enables the cyclic position SMS
01=1 minute rate
0=disables the power save mode
Case B
Command: wposc=1
Reply: wposc=1 OK
Description:
1=enables the cyclic position SMS with
the previous set rate
wms Set the accelerometer values.
[sensitivity: 00=disables sensor, 01=maximum,
10=minimum]
[timeout: 01÷99 minutes]
Command: wms=02,10
Reply: wms=02,10 OK
Description:
02=sensitivity level 2
10=10 minutes timeout
Safety Instructions
39
Tracker Management by SMS
39
Command
Meaning and Values Example
wgf Set the Geofence.
[status: 0=disable, 1=enable]
[LAT1,LONG1,LAT2,LONG2=latitude and longitude
for the 2 points defi ning the Geofence area]
NOTE: to enable or disable the Geofence function
without setting the area, sent the wgf command with
the fi rst fi eld only.
Case A
Command:
wgf=1,45g37.7981N,008g28.8012E,
41g37.8971N,012g28.8012E
Reply:
wgf=1,45g37.7981N,008g28.8012E,
41g37.8971N,012g28.8012E OK
Description:
1=enable
45g37.7981N,008g28.8012E=latitude
and longitude of the fi rst point
41g37.8971N,012g28.8012E=latitude
and longitude of the second point
Case B
Command: wgf=1
Reply: wgf=1 OK
Description:
1=enables the function considering the
previous defi ned area
40
Safety InstructionsTracker Management by SMS
40
Command
Meaning and Values Example
wanc Set the Anchor.
[enabling: 0=disable, 1=enable]
[radius: 0050, 0100, 0200, 0300, 0500, 0700, 1000,
1500, 2000, 3000, 4000 m; default radius: 0100]
NOTE: to set the tracker current position as area
center point, send the complete wanc command,
containing both enabling and radius fi elds (e.g.
wanc=1,0100).
NOTE: to enable or disable the Anchor function
without setting the radius, send the wanc command
with the fi rst fi eld only. In this case, the default radius
or the previously set radius is considered.
Case A
Command: wanc=1,0100
Reply: wanc=1,0100 OK
Description:
1=enables
0100=radius at 100 m
Case B
Command: wanc=1,0100
Reply: NO VALID CENTER POS
Description:
1=enables
0100=radius at 100 m
NO VALID CENTER POS=if the center
point cannot be detected
Case C
Command: wanc=1
Reply: wanc=1 OK
Description:
1=enables the function considering
the default radius or the previously set
radius
wem Erase all position data recorded in the memory. Command: wem
Reply: wem OK
Safety Instructions
41
Tracker Management by SMS
41
Command
Meaning and Values Example
wgprs Set the GPRS parameters and start the continuous
GPRS connection.
[setup: 0=set the GPRS parameters without starting
the connection,
1=connect with the new parameters (IP, PORT),
2=connect with the parameters previously preset]
[parameters: IP=host IP address, PORT=TCP port]
NOTE: the IP and PORT parameters should be
written between commas.
NOTE: if there is no GPRS connection, the tracker
sends an error SMS containing “GPRS ERROR”.
Case A
Command:
wgprs=0,”213.86.89.11”,”9500”
Reply:
wgprs=0,”213.86.89.11”,”9500” OK
Description:
0=set GPRS parameters without
starting the connection
213.86.89.11=host IP address (example)
9500=TCP port
Case B
Command:
wgprs=1,”213.86.89.11”,”9500”
Reply:
wgprs=1,”213.86.89.11”,”9500” OK
Description:
1=GPRS connection with new parameters
213.86.89.11=host IP address (example)
9500=TCP port
Case C
Command: wgprs=2
Reply: wgprs=2 OK
Case D
Reply: NO GPRS COVERAGE
Description:
NO GPRS COVERAGE=if GPRS signal
is missing
42
Safety InstructionsSetup by MyTrack Software
42
Setup by MyTrack Software
OPEN
MYTRACK
SETUP
ADDRESS BOOK
PRINT
PAGE SETUP
CONNECT
DISCONNECT
ZOOM
BAR
ZOOM
PAN
CENTER
FOLLOW
HELP
PLAY
PAUSE
STOP
FIRST
REWIND
FORWARD
LAST
BAR TO SCROLL
THE
RECORDING
INCREASE THE
RECORDING
SPEED
DECREASE THE
RECORDING
SPEED
RECORDING
SPEED
GEOPOINT
SETUP
INFORMATION
Power Save Mode
The Power Save Mode allows for optimal management of the battery tracker. It is possible to set the tracker
automatic switching on/off according to specifi c use requirements.
There are three Power Save Modes programmable by means of the provided software, except for Cyclic
Position SMS which is programmable by SMS command too. After Power Save Mode enabling, the tracker will
switch off automatically 2 minutes after tracker disconnection by the provided software.
WITH MOTION
Network Provider
10:30
OFF ON
MOTION
OFF
NO MOTION FOR A
PRESET TIME, NO DATA
EXCHANGE
Safety Instructions
43
Setup by MyTrack Software
43
WITH CYCLIC POSITION SMS
Network Provider
10:30
OFF ON OFF
CYCLIC POSITION SMS SENDING SMS SENT
Before using this mode, enable and set the Cyclic Position SMS function with
SMS rate 5 minutes.
During the automatic switching on, if the tracker is connected by the provided software, the automatic
switching off will be carried out after position SMS sending, after carrying out all the preset operations and 2
minutes after tracker disconnection.
WITH CYCLIC GPRS CONNECTION
Network Provider
10:30
OFF ON OFF
CYCLIC GPRS CONNECTION
Before using this mode, enable and set the Cyclic GPRS Connection function
with rate 5 minutes.
The tracker will switch off automatically after successfull GPRS connection and after carrying out all the preset
operations.
If, after two tries, the GPRS connection is failed, the tracker will switch off automatically.
44
Safety InstructionsSetup by MyTrack Software
44
To a set a Power Save Mode, connect the tracker to the provided software and access the setup window by
selecting Setup from Remote Unit menu.
Safety Instructions
45
Setup by MyTrack Software
45
Alarm SMS
To enable/disable the Alarm SMS and set the phone number, connect the tracker to the provided software and
access the setup window by selecting Setup from Remote Unit menu.
46
Safety InstructionsSetup by MyTrack Software
46
Position Data Recording
To set a data position recording, connect the tracker to the provided software and access the setup window by
selecting Setup from Remote Unit menu.
Safety Instructions
47
Setup by MyTrack Software
47
Update of the Tracker Firmware Version
To update the tracker, connect the tracker to the provided software and access the info window by selecting
Info from Remote Unit menu.
A new window is opened
for update fi le selection
During tracker fi rmware upgrade, on the tracker will be displayed UPGRADE...Please don’t turn OFF the
device!.
Wait until the update is completed, this occurs when the tracker is turned off.
If the tracker to be updated is connected with GSM/GPRS network, be sure
that the GSM/GPRS network signal level is high.
If the tracker to be updated is connected by a USB cable, do not remove the
cable during the update.
To perform the update, it is necessary to connect the provided battery charger
to the tracker.
48
Safety InstructionsMaintenance
48
Maintenance
The tracker and relevant accessories must be handled with care. Read the following instructions carefully.
Clean the tracker with a soft cloth, avoiding the use of corosive chemical products, solvents or aggressive
detergents.
Do not paint the tracker.
Do not swallow the accessories or small components of the tracker.
Avoid blows to the tracker which could internally damage the product.
Do not open the tracker in any way differently from the way indicated in the manual.
Do not wet the tracker. Humidity, condensation, rain or any other liquids containing mineral substances
could damage the electronic circuits. In the event of contact with liquids, remove the battery and leave
the tracker to dry.
Do not use or leave the tracker in particularly hot environments. High temperatures could damage the
electronic circuits, the battery and the plastic parts of the tracker.
Do not use or leave the tracker in particularly cold environments. Low temperatures could cause damage
to the electronic circuit boards of the tracker.
Do not use or leave the tracker in particularly dirty or dusty environments, the tracker could get
damaged.
Safety Instructions
49
Technical Features
49
Technical Features
GPS receiver: SiRFstarIII - 20 channels
GSM frequencies: 850 / 900 / 1800 / 1900 MHz
Data memory: 2MB non-volatile FLASH
Porta di comunicazione: no.1 USB
Sensor: no.1 for accelerometer
Dimension/Weight: 74 x 74 x 23 mm / 120 gr
Battery: model ABL-6C Li-ion - 3,7V 1000mAh
Battery charger: model ZD050050EU
input 100VAC - 240V 50/60Hz 0,15A
output 5VDC 500mA
Car charger: model ESC-004
input 13,6VDC
output 5VDC 500mA
Conformity: CE mark
CONDITION BATTERY
LIFE
Standby mode with motion sensor active. ~10 days
Tracking SMS every minute (GPS always on). ~9 hours
Tracking SMS every 5 minutes (GPS with hotstart). ~4 days
Continuous tracking. ~2 hours
Data connection, with GPS system continuously active. ~2 hours
Position data recording every minute. ~37 hours
Tracker not in use. ~2 days
Tracker in communication on GSM network. ~4 hours
50
Safety InstructionsManufacturer’s Limited Warranty
50
Manufacturer’s Limited Warranty
This warranty does not limit the user’s (statutory) rights under applicable national laws relating to the sale of
consumer products.
During the warranty period, the Manufacturer or Manufacturer authorized service company will in a commercially
reasonable time remedy defects in materials, design and workmanship free of charge by repairing.
The Manufacturer will, in accordance with this Limited Warranty (unless otherwise required by law), remedy
defects by repair or, should the Manufacturer in its discretion deem it necessary, replace the Product.
This Limited Warranty is only valid and enforceable in the country where the user has purchased the Product
provided that the same Product has been intended for sale in that country by the Manufacturer. However, if
the user has purchased the Product in a member state of the European Union, Iceland, Norway, Switzerland
or Turkey and such Product was originally intended by the Manufacturer for sale in one of these countries,
this Limited Warranty is valid and enforceable in all of these above listed countries. Some limitations to the
warranty service may apply because of country specifi c elements in the Products.
Warranty Period
The warranty period starts at the time of Product’s original purchase by the fi rst end-user. The Product may
consist of several different parts and different parts may be covered by a different warranty period. The
different Warranty Periods are:
24 months for the device
6 months for the following consumable parts and accessories: battery, chargers, headset, device cover
90 days for the media on which any software is provided, (e.g. CD ROM, DVD,...)
As far as national laws permit, the warranty period will not be extended or renewed or otherwise affected due
to subsequent resale, repair or replacement of the Product authorized by the Manufacturer.
www.cte.it
www.cte.it
Distributed by
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Midland GEOPOINT LCD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Midland GEOPOINT LCD in de taal/talen: Engels als bijlage per email.

De handleiding is 1,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info