658472
16
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
16
XL48 Microphone Pre-amplier
2. Getting Started
This section shows you how to unpack, install, connect up, power up and
congure the XL48 unit.
This equipment is supplied by a mains voltage that can cause electric
shock injury.
Before installing, setting up or operating this equipment, make sure
that you have read and fully understand all of this section and the
“Important safety instructions” at the front of this manual.
2.1 Unpacking
Carefully unpack your XL48 equipment package.
Then, inspect the XL48 unit carefully for any signs of damage that may have
occurred during transit and notify the courier immediately if you discover any.
Check the contents of your XL48 equipment package. If there are any parts
missing, incorrect or faulty, please contact your local distributor or Midas at the
address at the front of this manual.
Please retain the original packing in case you should need to return the
equipment to the manufacturer or supplier, or transport or ship the unit later.
2.2 Installation
Before installing and operating this equipment, make sure it is correctly
connected to the protective earth conductor of the mains voltage supply socket
outlet through the mains lead.
Ideally a cool area is preferred, away from power distribution equipment or other
potential sources of interference.
Do not install the equipment in places of poor ventilation.
Do not install this equipment in a location subjected to excessive heat,
dustormechanical vibration. Allow for adequate ventilation around
the equipment, making sure that its fans and vents are not obstructed.
Wheneverpossible, keepthe equipment out of direct sunlight.
Mount in rack only.
Power
The supply cord must be unplugged to ensure complete
de-energisation of the unit.
The internal power supply is of the switch mode type that automatically senses
the incoming mains voltage and will work where the nominal voltage is in the
range 100VAC to 240VAC.
A mains inlet is provided on the rear panel. The correct lead for connection in
the area to which the unit was shipped is supplied with the unit. The equipment
should only be plugged into the mains outlet using the supplied lead.
Handling the equipment
When lifting or moving the equipment, always take its size and weight into
consideration.
Completely isolate the equipment electrically and disconnect all cables from the
equipment before moving it.
Do not insert your ngers or hands in any gaps or openings on the equipment,
forexample, vents.
Electric elds
In accordance with Part 15 of the FCC Rules & Regulations, “… changes or
modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.”
Should this product be used in an electromagnetic eld that is amplitude
modulated by an audio frequency signal (20 Hz to 20 kHz), the signal to
noise ratio may be degraded. Degradation of up to 60dB at a frequency
correspondingto the modulation signal may be experienced under extreme
conditions (3V/m,90% modulation).
2.3 Connecting up
Connect up the rear panel of your unit as required:
• Inputs:
• XLR mic/line inputs (up to eight).
• Parallel analogue inputs (eight).
• External word clock.
• Outputs:
• AES3 outputs. There are two sets of eight AES3 mono output channels
(1 to 8), one set are on connectors 1 to 4 and the other set are on
connectors 5 to 8.
• Analogue outputs (eight).
• ADAT outputs (optional) — for connecting, for example, a sound
card (for PC) or an ADAT recorder. At 44.1kHz and 48kHz sample
frequencies the two ADAT ports are identical and both provide eight
output channels (1 to 8). At 88.2kHz and 96kHz sample frequencies,
bothportsprovidefour output channels each (port 1 = channels 1 to 4
and port2= channels 5 to 8).
• Internal word clock.
• Mains power — connect the IEC connector of the mains cable into the rear
of the unit and then plug it into a mains power outlet.
2.4 Powering the unit on/o
As the XL48 has no power on/o switch the unit is powered on/o via the
mainsoutlet.
2.5 Conguration
After you have powered up the XL48 you can congure the clock source and
sample rate as required.
midasconsoles.com
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Midas XL48 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Midas XL48 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info