776238
11
Verklein
Vergroot
Pagina terug
1/204
Pagina verder
MI 3152(H) EurotestXC (2,5 kV) General description
10
Trip out time measurement for B and B+ type RCDs in AUTO function is made with sine-
wave test current, while trip-out current measurement is made with d.c. test current (MI
3152 only).
Z loop, Zs rcd
The specified accuracy of tested parameters is valid only if the mains voltage is stable
during the measurement.
The measurement accuracy and immunity against noise are higher if I test parameter in
Zsrcd is set to ‘Standard’.
Fault loop impedance (Z loop) measurements will trip an RCD.
The Zs rcd measurement does not normally trip an RCD. However if a leakage current
from L to PE already flows or if a very sensitive RCD is installed (for example EV type)
the RCD could trip. In this case setting parameter I test to ‘Low’ can help.
Z line, Voltage drop
In case of measurement of ZLine-Line with the instrument test leads PE and N connected together
the instrument will display a warning of dangerous PE voltage. The measurement will be
performed anyway.
Specified accuracy of tested parameters is valid only if mains voltage is stable during the
measurement.
If the reference impedance is not set the value of ZREF is considered as 0.00 Ω.
The highest value of Zref, measured at different settings of the Test or Phase
parameters is used for Voltage drop (ΔU) measurement in Voltage drop single test,
Zauto single test, auto tests and Auto Sequences®.
Measuring Zref without test voltage present (disconnected test leads) will reset Zref
value to initial value.
Power, Harmonics, Currents
Consider polarity of current clamp (arrow on test clamp should be oriented toward
connected load), otherwise result will be negative!
Illumination
A 1172 and A 1173 illumination probes are supported by the instrument.
Artificial light sources reach full power of operation after a period of time (see technical
data for light sources) and should be therefore switched on for this period of time before
the measurements are taken.
For accurate measurement make sure that the milk glass bulb is lit without any shadows
cast by hand, body or other unwanted objects.
Refer to the Illuminance handbook -for more information.
Rpe
The specified accuracy of tested parameters is valid only if the mains voltage is stable
during the measurement.
Measurement will trip an RCD if the parameter RCD is set to ‘No’.
The measurement does not normally trip an RCD if the parameter RCD is set to ‘Yes’.
However, the RCD can trip if a leakage current from L to PE already flows.
IMD
It is recommended to disconnect all appliances from the tested supply to receive regular
test results. Any connected appliance will influence the insulation resistance threshold
test.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metrel MI 3152 - EurotestXC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metrel MI 3152 - EurotestXC in de taal/talen: Engels als bijlage per email.

De handleiding is 6.49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Metrel MI 3152 - EurotestXC

Metrel MI 3152 - EurotestXC Gebruiksaanwijzing - Nederlands - 85 pagina's

Metrel MI 3152 - EurotestXC Gebruiksaanwijzing - Deutsch - 213 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info