599580
16
Verklein
Vergroot
Pagina terug
1/121
Pagina verder
ENGLISHen
16
See page 2.
1"Quick"clamping nut *
2Support flange *
3Spindle
4WE
A
...: Autobalancer support flange (non-
detachable) *
5 Spindle locking button
6 Electronic signal indicator *
7 Lock (to prevent the machine from being
switched on unintentionally, or for continuous
operation)*
8 Trigger (for switching on and off)
9 Button (to turn the main handle)
10 Main handle
11 Additional handle/Additional handle with
vibration damping
12 Safety cover
13 Adjusting nut *
14 2-hole spanner *
15 Quick-release clamp (to adjust safety guard
without the use of tools)
16 Screw (to adjust clamping force of quick-
release clamp)
* depending on equipment/not in scope of delivery
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
rating label, match with your power supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
Use only extension cables with a min. cross-section
of 1.5 mm
2
. Extension cables must correspond to
the power consumption of the machine (cf
Technical Specifications). If a cable roller is used,
always roll up the cable completely.
6.1 Attaching the additional handle
Always work with the additional handle (11)
attached! Manually screw in the additional
handle securely in the left, centre or right threaded
hole (depending on requirements).
6.2 Attach the safety guard
(for working with abrasive discs)
Prior to operation: Attach safety
guard.
For reasons of safety, the safety guard (12)
should always be attached when roughing
work is performed.
For reasons of safety, the special parting
guard should always be attached before
parting work is performed (see chapter 11.
Accessories).
See illustration E on page 2.
- Open quick-release clamp (15). Mount the safety
guard (12) in the position indicated.
- Turn the safety guard until the closed section is
facing the operator.
- Close quick-release clamp.
- If necessary, increase clamping force of quick-
release clamp by tightening the screw (16) (with
opened quick-release clamp).
Use only accessories that
are covered by at least
3.4 mm by the safety guard.
6.3 Pivotable main handle
Only work with the main handle (10) engaged.
See illustration B on page 2.
- Push in the button (9).
- The main handle (10) can now be turned 90° to
both sides and can be engaged.
- Make sure that it is securely positioned: the main
handle (10) must be engaged and it should not be
possible to move it.
6.4 Power-supply connection
The mains sockets must be protected using time-
delay fuses or circuit breakers.
Machines with "WE..." in the model designation:
(with inbuilt automatic startup-current limitation(soft
start).) The mains sockets can also be protected
using fast-acting fuses or circuit breakers.
Prior to any conversion work: Pull the mains
plug from the socket. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard
before performing parting work (see chapter
11. Accessories).
7.1 Locking the spindle
Press in the spindle locking button (5) only
when the spindle is stationary!
- Press in the spindle locking button (5) and
turn the spindle (3) by hand until the spindle
locking button engages.
7.2 Placing the grinding wheel in position
See illustration C on page 2.
Machines with the designation W 2..., WE 2...:
- Fit the support flange (2) on the spindle. The
flange should not turn on the spindle when
properly attached.
- Position the grinding wheel on the support flange
(2) as shown in illustration C.
The grinding disc must lay flat on the supporting
flange.
Machines with the designation WEA 2...:
The Autobalancer support flange (4) is
permanently fitted on the spindle. As is the
case with most other angle grinders, a detachable
support flange is not necessary.
5. Overview
6. Commissioning
7. Attaching the grinding disc
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo W 22-230 MVT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo W 22-230 MVT in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info